My Asymmetric Electrodynamic Machines

[Ufopolitics]

A Question for the Skeptics...for the FREE ENERGY deniers

@All the FREE ENERGY SKEPTICS, DENIERS...NAYSAYERS...

This is a Question...I would LOVE ANY Skeptic or Free Energy Naysayer ...if they could give Us all a Rational Answer...related to the above Video Test...

If the Batteries only lost say 100 Milli Volts (We noticed NO AMP LOSS)

And Super Caps GAINED up to 4.99 Watts...

and...The question:

¿Where did This 4.99 Watts came from?

I will be waiting...I know I should not hold my breath waiting right?...


Ufopolitics

[Ufopolitics]

One Main Thing to have in Mind...

Now Guys...

One Main thing to have in mind when it comes to Calculate FULL OUTPUT of Asymmetrical Machines.

We MUST consider:

1- ELECTRICAL POWER OUTPUT

2- MECHANICAL POWER OUTPUT

Then We must realize:

In the above Video Test 1, I have completely disregarded MECHANICAL POWER OUTPUT, which MUST BE ADDED to Total Watts Output....Meaning the FIVE (5) Watts Electrical Power Output is NOT THE COMPLETE TOTAL OUTPUT of this little Machine!!

However, We, the Members of this Forum, building this Type of Asymmetrical Machines CAN AFFORD to GIVE AWAY (For this tests only, don't get excited...) Our Excellent Mechanical Output...just because...just measuring Electrical Energy Output...We ACCOMPLISH OVERUNITY...and in this case as follows:

Total Power Generated = 4.99 Watts

Total Power Input*** = 2.24 Watts

If We do the "Elementary School Math"...

Then, We get a COP=2.22 , and Efficiency = 222 %

***NOW...Wait a Minute!!...We are NOT supposed to divide FULL INPUT as above...BUT, ACTUAL POWER LOST...Right?

That would be subtracting starting Battery Power to ending Battery Power RIGHT?...but OMG! ...We did not loose absolutely NADA!!

I have been "Generous" by doing that calculation above...now, all of you know it works based on Total Power Inputted to the System, therefore, LOST...just because Batteries were not drained...or whole or majority of their power was transferred to the Caps...Oh no! ...BUT, that did not occur...

Feel free to tell me if am wrong here, like I mentioned on video.

And I am Opening Doors to Anyone who wants to give their Opinions here in the OPEN (NO PM's)...and absolutely, that includes Farmhand and dR NoGreen...

I promise I will not get Harsh...


Regards to All


Ufopolitics

[Ufopolitics]

Video Frames on Power Readings

Hello Guys,

Here are Four ESSENTIAL Frames taken from Video.

1-SUPERCAPS STARTING POWER READING

[IMG][/IMG]

2- SUPERCAPS ENDING POWER READING

[IMG][/IMG]

3- BATTERIES STARTING POWER READING

[IMG][/IMG]

4- BATTERIES ENDING POWER READING

[IMG][/IMG]

Even though Batteries show a loss of 0.086 Milli Volts (Based on Batt Frame 1...versus Batt End Frame V readings)...when we compare Start-End Batteries Wattage Power...We can see they lost absolutely NADA...Nothing...

Due to a "slight increase" of 0.03 mAmps...


Regards to All


Ufopolitics

[Ufopolitics]

Hello All

Great video UfO
It proves that the little motor runs and recharges itself.

Hello Randy,

Nope, it means :

That Little Motor is capable of Charging from almost ZERO (actually and exactly 0.026 mV X 0.010 mA=0.0026 WATTS), Four 2.7V/ 310 FARADS SuperCaps. Using Two NiMH 1.2V/2200 mAh...and this little Batteries lost 0.084 mVolts.

And it means more...read Total Caps END Wattage, versus Total Batteries END Wattage...do some Elementary School Math...calculate C.O.P, Efficiency...and "UNITY" there...

Calculate how much exactly Batt lost...

Ask Yourself then...¿Where did all this Energy came from?

And have in mind I will be COMPLETELY IGNORING Mechanical Power Output...actually we can AFFORD to have OVERUNITY with JUST Electrical Out to Electrical In ...period

What does the rain gauge read...
Sounds like quite the rain storm where you're at...
Be well.

All the Best
RandyFL
ps have a great weekend

Well You live in Florida right?...so you should know we are going through rainstorms every afternoon...


Regards and You too have a great weekend...I will be working on the Master Video.


Ufopolitics

[RandyFL]

Radio Shack Motor

Hello All

Great video UfO
It proves that the little motor runs and recharges itself.

What does the rain gauge read...
Sounds like quite the rain storm where you're at...
Be well.

All the Best
RandyFL
ps have a great weekend

[Ufopolitics]

Over Unity Test Unedited Video Track.

Hello Guys,

Below is my "Over Unity Test Unedited Video Track."

OVERUNITY_TEST_UNEDITED_TRACK_1

I meant to do this test before...and as a matter of fact I talked about it on one of the Three Videos Testing the Supercaps with different connections and this Five Pole RS Motor. Can't remember exactly which one it was, but definitively is there.

Now this is the Raw, High Def. MPEG Unedited Video Track that would go into the coming Full Video with my Ufopolitics Intro, Background Music, Text Explanation, Calculation Analysis, Time CAD Graphics, Circuit Diagrams, Detailed Frame by Frame readings of Power (VXA=W) Measuring Tools PDF Spec's as Resolution and Error Percentages...etc,etc.

I have decided to load this video first as "Unlisted", just for the EF Members here, as it will take me pretty long time to build, render, batch all this processes to Master the coming video, OVERUNITY TEST ONE...

I don't know if YT will allow me to upload the Full Video, since this one is over 29 Minutes...and by the time I add all other stuff, it will get close to the Hour Time.

It will be on this Link, so you Guys could download it, analyze it, and comment on it as you please...


Regards to All and Thank You for taking your time to watch it.


Ufopolitics

[Fingregor123]

Et Voila.



Have to go out for a day or two but will return. Shall try to find some 5 poles on my travels.

Thanks and all the best....back Monday/Tues

Nice Midaz

Regards

Finn.

[Midaztouch]

Finn

aboard! Study hard! It looks like you will be our representative in Scotland!


Keep it Clean and Green
Midaz

[Ufopolitics]

Ouch...

3 Poles

Can take them back but that's all they had, mail order from somewhere in the UK may be the best bet?

Regards

Finn.

Ouch!...

A Three Pole is good, but related to all north design, it does not have overlapped coils advantage, which keeps transferring energy from Pair to Pair...delivering a more robust flow.

However, a Three Pole is even more simple to build, winding wise...all coils are exactly the same winding direction and each one is independent from the other...so it can be done as well...plus you have more room to add more turns...

Does it have carbon brushes or copper strips rubbing the commutators?


Ufopolitics

[Fingregor123]

3 Poles

Can take them back but that's all they had, mail order from somewhere in the UK may be the best bet?

Regards

Finn.

[Ufopolitics]

Great!!

FYI - Little Update.

2x Motors bought, wire 26 SWG 0.450mm (closest I could find.)

Battery box, only thing they had was 2x1.5v, and the motors are 6-15V

Will try and find a 4x1.5v battery box on my travels ASAP.



Now reading and re-reading until dis assembly begins.

Regards

Finn.

Hello Finn,

That is just great!

Now, when you open plastic envelopes...and get them out, could you shut a couple of pic's zoomed of Both rear and front (just one pic is fine, one facing frt and other rear in a 45º to Cam) so I could see rear & frt in one shot.

I would like to guide you properly on the cuts, so you do not go through trouble putting main asymmetric housing together.

About the "Factory Rated Voltages"...disregard them......after You are done with this new motor assy... it would expand the V Ratio from 1.5-3.0 to 18V (Hauling A** of course)...So, a Battery Box of Two (1.5 X 2) is fine...to run it in Parallel Feed (like We normally did before Side Banks...for side Banks they would be fine also...but rather start with single 1.5 holders on each side bank first...because 2X1.5V at each Bank would make this motor fly with that new asymmetric winding...

And anxious to see how many poles are their Rotors...


Regards


Ufopolitics

[wantomake]

Wisdom

Thanks Ufopolitics,
This is exactly what I need to hear. Good wisdom from someone with experience.
I was in Japan for summer last year. Live in South Carolina.

I'm sure experiments are best to understand how a device should be designed, but to have something to use as a blueprint would be an advantage. There's got to be a better way to start and get results while building a device.

Yes I still use the treadmill motor/generator from time to time.

Thanks Dana, I agree this will be expensive in time and resources. But two years of my time and four years from the other people who are working on this device, it would seem we would be past the stage we are at. As you said I can communicate better also.This I believe (being inspired by Ufopolitics) is a most important tool for anybody in replicating a free energy device.

Thanks again for your wisdom,
wantomake

[Fingregor123]

FYI - Little Update.

2x Motors bought, wire 26 SWG 0.450mm (closest I could find.)

Battery box, only thing they had was 2x1.5v, and the motors are 6-15V

Will try and find a 4x1.5v battery box on my travels ASAP.



Now reading and re-reading until dis assembly begins.

Regards

Finn.

[prochiro]

Wantomake

A cad program is a drawing or blueprint of what you have decided to make. You select the parts and how they go together. Some of the high end programs will check the drawing for general errors but not to the extent you asked about where they would suggest other parts. A 3D cad will show how the parts will look in three dim. I am afraid that if you want to put the project on a three Dim. and have the power to show how it works and redesign itself that you will come up short. There are programs costing many thousands of dollars that are helpful in some ways but the education to run one of these is great as as is the time. For designing a system nothing is better than learning to do it yourself. For showing others about your system, nothing is better than a cad.

Dana

[Ufopolitics]

It is all about "Your Programming"...

Ufopolitics,
You don't have to answer this if I'm being rude to post here this question.

I was a part of this adventure in the beginning and enjoyed with much learning, the modified motor generator I built from your instructions. I stopped cause can't afford the imperial motor, but still keep up reading here. Thanks for those good times.
Have been working on the elusive lockridge device for some time now. That's the reason I ask you.

Here is my question if you don't mind;
Will a high end 3D cad program with electrical, electronics,electromagnetic, transformer effect and the such, would it show all the effects each part of the device and how to tune or change parts of the machine?

If I'm way off here just call me crazy and I'll understand.

An old member and friend,
wantomake

Hello Wantomake, long time!

Of course I remember!...You had that Treadmill Motor converted...and You live in Japan...if am right...

I have "High End 3D CAD Programs"...and most of this programs have an Embedded Language-Code to program it yourself on whatever you want it to do...You set the New Strings, New Parameters...Fields, teach it how to interpret, etc,etc.

But to tell You that they have all this Electronic, Electrical, Electromagnetic, Transformer Effects "FUNCTIONS"...in order to tune/maintain/replace parts on a Device you will build/create within its Platform, from scratch...I honestly doubt such Program Exists...
However, You do can make all this happen, by Programming it yourself......Now, any "defects, errors or malfunctions" would be blamed on the programmer...not the program...

I tell You a short story...

When I was building my 3D models, based on one of my Patents in MAYA 3D (the old version from Alias Wavefront, not the new one from the new owners, Auto Desk [creators of Auto CAD])...I programmed the software to do all this changes of colors codes, over a time track of animation based on rotation...Colors were assigned based on Polarity, where Blues and all derivatives of Blues were North...and South were all the Gamma of Reds...passing through Orange all the way to Yellow....since I had "many Norths, and many Souths"...wanted to rotate them and turning "ON" by giving them more "Brightness"...while when OFF, I turned them ALL same Neutral Color...White....the switching from off to on, and viceversa was done smoothly passing through different shades (Program did that through a "dimming curve")...

The point is that by observing this changes of shades in rotation at different speeds in long sessions, ...I was able to "see" , define those "Inertial/Idling" Planes...within the 360º Quadrant...and that gave me the "Generation Stage" in perfectly defined angles...That was how the Dual Mode (motor-generator) Asymmetric Machines were born.

So, yes, this high end programs have infinite possibilities my friend, you could do whatever you want to achieve with them...it is all about the way you "teach them"(command them) how to perform the required Functions.

However, there may be many programs out there , newer ones, that may do more advanced functions "pre-build" within their main core...but I do not know of any that could do -without major programming- all you want to achieve.


Kind Regards


Ufopolitics