My Asymmetric Electrodynamic Machines

[Midaztouch]

G'day Midaz

The motor is a 20pole 4 stator magnets
I already did a load test it had electrolytic capacitors before it is here

https://www.youtube.com/watch?v=LgG2mS38aAY

I will not be doing another load test until it is fixed in Nessie then my test driver will drive her up to visit Cornboy with me sitting on the back

After I do the other test I mentioned earlier I will be doing the same test as above but with an Imperial P56 and see how she goes

I imagine I will receive the 3000F's sometime next week and when I set them up the bank will be 25 3000F 2.7v in series being 3000F @ 67.5v

I will have my hands full

Kindest Regards

Kogs sick of the ranting by those who have to disrupt this thread

@ Kogs

Yes, I saw that video a while back. It was really good! I didn't realize that you were only using one channel to drive your motor and collecting 3 channels from the generator, while under mechanical load. That motor is really strong!

What I was hoping to see was the volt meter connected to the caps bank. I wanted to see speed of the caps charging under mechanical load.

I understand your driver's impatience. It's like having a new car and the ignition switch in not installed properly. (GM recall)

Keep up the great work! It's almost show time for you and Nessie!

Keep it Clean and Green
Midaz

[Aaron]

This Thread

Hello Aaron,

Do I need to stand the attacks from this guy on this Forum?...Because in my You Tube Channel was a matter of just pressing a key, and Banning His stinking odors FOR EVER.

Aaron You seem to know about Legal Rights and Legalities a lot...this guy here is attacking, insulting me, but worst, he is accusing me of being a Plagiarist,and that is serious , you know that is called Defamation in front of Thousands of my People, basically people that has work with me for years by now.



I am just asking if there is something you could do related to this situation as one of the Creators of this Forum.


Really appreciate your help


Ufopolitics

Hi UFO, I've been swamped with conference business the last few days so haven't kept up here.

@ALL, let's please respect everyone's contributions and let UFO handle his own thread how he likes. If any serious moderation is needed other than this, I'll have to hand it over to another moderator so I can stay out of it - I'm much too close to all of this.

[Matthew Jones]

This post, My Post here, is NOT intended to respond to MJ, but for all of you to see what He is claiming to be what I have shown on my videos and he claims to be a "Plagiarism" to his work.

This is NOT gonna end here MJ...it is just the start.


Ufopolitics

But you are responding to me. Its not complete plagiarism of my work its a lot of peoples work. 4 times I have seen mine displayed as yours. No mods to speak of. Your motor is garbage so you keep that one. I know you were trying to copy the verbal description of we were doing but you had no details. LOL

I know its not over, as long you choose to mislead people I'll be pointing out.

And grow up even you are capable of typo. If thats all you can drag up is my English than your gonna be in for ride

Sincerely
Matthew Jones (My real name)

[thebanano]

Cool As Ice

Greeting everyone...
First, sorry for my english as not my native languange...
I'am with this thread since the beginning of this thread was starting. Only time that force me to not following every step that you've achieve (so fast), for almost three years.
And for ufo, you have a heart as big as the ocean, my friend. For my sugestion, ignoring all the crap, mice, that still sniffing every move you make...Like dana's said "jealousy" was they energy, and that wasn't constructive, wasting your energy a lot to handle.

So, congrat for your monopole motor, perhaps i still have the time to construct it, starting with rs motor, and share it here...

salute for ufo team

[sampojo]

Kogs video

I posted there: Hey Kogs, what a dream. great work. (samopjoe). So the other three brush sets in gen mode are putting their energy back into the system when just the one is in motor mode?

Also, you are using the N-S asymmetric windings as opposed to the unipolar, correct?

Even with the N-S windings, implication is you won't be charging the battery sets very often when you start motoring around?

[iankoglin]

@ Kogs

Thank you for all of your hard work. Let's ignore the fighting and concentrate on your testing. Your motor runs very smoothly. I know its 1000w. How many poles and stators is it? Will you be doing a mechanical load test soon? I curious to see the caps charging speed with the mechanical load on it.


Keep it Clean and Green
Midaz

G'day Midaz

The motor is a 20pole 4 stator magnets
I already did a load test it had electrolytic capacitors before it is here

https://www.youtube.com/watch?v=LgG2mS38aAY

I will not be doing another load test until it is fixed in Nessie then my test driver will drive her up to visit Cornboy with me sitting on the back

After I do the other test I mentioned earlier I will be doing the same test as above but with an Imperial P56 and see how she goes

I imagine I will receive the 3000F's sometime next week and when I set them up the bank will be 25 3000F 2.7v in series being 3000F @ 67.5v

I will have my hands full

Kindest Regards

Kogs sick of the ranting by those who have to disrupt this thread

[Midaztouch]

Aaron posted this in 2007

If you goto the homepage, http://www.energeticforum.com
in the left column, click USER CP in the site navigation menu
(towards top left).

http://www.energeticforum.com/usercp.php

Then in the left column control panel menu towards the bottom,
there is a link that says:

Buddy / Ignore Lists

click that and it goes here:
http://www.energeticforum.com/profile.php?do=editlist

Add a name to the ignore field and click Save List.

I believe that is all there is to it. Please post here if that did
or did not work.

[Ufopolitics]

So you might wanna look at that thing he's posting. Since UFO is not capable of being honest. The truth is, and this fact you can find it at level of electrical engineering.
When you put 2 capacitors in series and discharge them no matter how little, no matter the size of the capacitor you loose 50% of your energy in capacity.
This is a LAW of capacitance. Now UFO claims all kinds of things but most of them are only believable if you don't do real research.

Do not spend money on those super caps because there are better ways. Any BOOST circuit can deliver at least 96% efficient delivery of energy, some higher. Batteries can be switched and I have reposted the circuit he tried to copy over "Use For the Tesla Switch". You can download an entire PDF I posted 4 years ago on the use of these similar circuit.

On that note any one of you can build a motor that is 10 - 20 (COP's up to 8) times more efficient than what he showing you and are spending money on just by reviewing some of the history on this board. Motors that generate and create torque.

He selling tech and propaganda that does not add up does not belong to him, and all of you have sucked it up for some time now. But do what you want.

For me its important people who worked hard finding some of this get the credit for being starting point and I will continue to inform on UFO's plagiarism.

Cheers'
Matthew Jones

This post, My Post here, is NOT intended to respond to MJ, but for all of you to see what He is claiming to be what I have shown on my videos and he claims to be a "Plagiarism" to his work.

Since MJ did not have the courage to show it himself, I had to take my time and search through this whole Thread to find what he is claiming.

All this thread is about, are Variations of a TESLA SWITCH, originally Patented by Nikola Tesla back on his times, and now a Public Domain Patent.

One thing this guy doesn't know...that no matter how many changes, and improvements based on new technology are made to an original patent...still, the Main Essence of that Patent PREVAILS as the ORIGINAL MATERIAL...No matter this, NONE of all the work displayed on that Thread resembles -at all- any similarities to My Work...since My Circuit is based on MY MACHINES, MY ASYMMETRICAL MACHINES as the center, the heart of the whole battery-capacitors, switches circuitry.

BroMikey shows this link on this POST to the main pdf article, where Mathew Jones is mentioned "as one of the MANY People" that has REPLICATED the "VERSIONS" of the TESLA SWITCH.

Following Images are taken from Mathew Jones CONTRAPTION, He claims to be where I have copied, or Plagiarized...

Below are the Diagrams for the Contraption:

[IMG][/IMG]

[IMG][/IMG]

And below are MJ Contraption Build...

[IMG][/IMG]


[IMG][/IMG]

A "quick" Drawing of His Contraption:

[IMG][/IMG]

Another Misspelling ..."COMMUNTATOR"...Did you ever heard of Spelling Correction Software?
I mean, for Public Display of your work...it is a shame you do this "kinda" mistakes.

Now, you guys, take a look at this, mainly the Diagrams...and tell me, where on Earth, are -even- similarities to my work displayed...except that has "batteries" coils...and a symmetrical motor...

However, I have noticed you have been looking for such a fast "rotary switch"...capable of alternating coils at faster speeds...yes, that is called ASYMMETRIC MACHINES BY UFOPOLITICS

He selling tech and propaganda that does not add up does not belong to him, and all of you have sucked it up for some time now. But do what you want.

First Mathew Jones...you must write it in a better English...like: "He IS selling tech"...you must use the verb "TO BE" for the Third Person (He) between Noun (He) and Verb (selling)...come on, for a "SPIC" Spaniard like Me, RIGHT?...with such terrible (not Southern US) accent...it is unthinkable... I have to correct your NATIVE Language Grammar!

But, related to the content of your post above... could you show here, anywhere ...WHERE AM I SELLING ANYTHING to anyone on this Forum, or in any of my sites, YT channels, etc,etc?


You are SO FULL OF IT...So much... that spills from all your orifices without being able to stop the stinking FLOW.

Maybe you are developing some Mental symptoms from being shocked so hard by High Voltages building your contraptions...you should see a Doctor...seriously.


This is NOT gonna end here MJ...it is just the start.


Ufopolitics

[Midaztouch]

@ Kogs

Thank you for all of your hard work. Let's ignore the fighting and concentrate on your testing. Your motor runs very smoothly. I know its 1000w. How many poles and stators is it? Will you be doing a mechanical load test soon? I curious to see the caps charging speed with the mechanical load on it.


Keep it Clean and Green
Midaz

[prochiro]

As time allows I will start going through this thread and pulling out the circuit that you have copied and posting them with the links to to thread they came from.
Some of the copied stuff he claimed was his, is in other threads as well. I will also start trying to dig them up.

No one says you don't have the right to use open source material, and no even demands credit. Thats just polite way of doing it.

But when you start posting circuit that DON'T WORK, like capacitor based Tesla Switch then you are just misinforming people. When they finally spend all that money they spent in worship of they're beloved UFO they will never again venture down the power of that parallel/serial switch. You'll will have ruined them.

As far as those winding patterns go, well thats just a joke. LOL and funny one too.

Sincerely
Matthew Jones (My real name)

I asked UFO a question and you butted in. You misunderstood the context of my question and proceeded to show me in large letters how a capacitor works in series. We are using the switch to test limits of the motor. You claim it does not work, that is bunk. If you can not get it to work then maybe you are not as smart as you say you are. No one set you as forum policeman here and I do not think you understand what you motor does and what it can do. As you stated earlier, anyone can make a stronger motor, but they cant make it run with so little power. I think you are jealous. Please do not tell me how to spend my money or try to save me from making a mistake. Maybe if you spent more time and money working on your tesla switch, it might work.
Dana

[iankoglin]

G'day UFO and Team
I have at last made a video of Nessie's motor using Nessie's circuit that UFO designed for her Thanks UFO
I have a bank of Super caps in parallel with the 48v Battery
In the video I show the changing of the electro gears and the regenerative power of this 1000w Chinese Motor asymmetrically modified it now only draws 1amp @50v unloaded through out this video
This motor is wound North & South I am still happy with it's performance
The video is in 2 parts because of its size they are here

https://www.youtube.com/watch?v=_n59jpOTPsg

https://www.youtube.com/watch?v=eSEUTYHqLCs

I am really pleased with the progress of my replications

Tomorrow I will be making a video of one of my smaller 250w modified motors and wiring it showing normal electrolytic connect as per UFO's instructions

In the near future I am going to setup my Imperial P56 motor wound the same N&S way and I will also make a video of it.
I will after I finish Nessie wind one of my Imperial motors All North's to compare

Kindest regards


Kogs slowly but getting there

[Matthew Jones]

As time allows I will start going through this thread and pulling out the circuit that you have copied and posting them with the links to to thread they came from.
Some of the copied stuff he claimed was his, is in other threads as well. I will also start trying to dig them up.

No one says you don't have the right to use open source material, and no even demands credit. Thats just polite way of doing it.

But when you start posting circuit that DON'T WORK, like capacitor based Tesla Switch then you are just misinforming people. When they finally spend all that money they spent in worship of they're beloved UFO they will never again venture down the power of that parallel/serial switch. You'll will have ruined them.

As far as those winding patterns go, well thats just a joke. LOL and funny one too.

Sincerely
Matthew Jones (My real name)

[Matthew Jones]

Didn't you right this to me?

"Hey, Hill Billy,

Stop insulting Me, accusing me of plagiarist and all your BS crap.

If you have a "Patent" on building a Parallel-Series Switch...go for it...SHOW IT.
Show proof DATE STAMPED, not altered.

The Motor MY MOTOR DESIGN, is the CENTER of that circuit, only ignorant people like you, that don't even know how to write English without misspellings, can write such an idiot comment.

Remember when you wrote that you have designed a motor just like mine?...LOL...Poor imbecile...not even in your dreams you could ever come up with such design.

GET LOST"

Who's racist?

[Matthew Jones]

Wow, going all out to cover your tracks now. Making things up even. Trying to make me look racist even. Thats a new one.

Why not just give credit, just mention when you copy someone stuff. Or at least when you copy don't change it to something that doesn't work. Like a capacitor based Tesla switch. I mean DUH!

I guess if you can't stand the heat....

Matt

[Ufopolitics]

Mathew Jones, The Racist comments

Mathew Jones in GOOGLE PLUS

Matthew Jones
8:30 PM

I hear ya talking like you always do.... Lame, lame, lame. Keep on taking other peoples work, lots of people are watching. Then use your real name, I dare ya, ya low life spic. Just be accountable like real man.Sincerely

Keep writing Mathew Jones...you are showing to all who you really are.

spic
spik/noun
US informal offensive
noun: spic; plural noun: spics

a contemptuous term for a Spanish-speaking person from Central or South America or the Caribbean.