My Asymmetric Electrodynamic Machines

[sebosfato]

Hello,

I could translate to portuguese if you wan't i just would like to understand a little better...


Lsmare, i guess he is saying the polarity reverses because of the return energy, the princes.

When the coil is being discharged the current flowing thru the load creates this reversed magnetic field.

Is that correct?

Regards

[s e t h]

i think at this point in time Ufopolitics can call it whatever he likes.
if the rest of us can understand it like him we'll be lucky.

edit:nvm /edit

[prochiro]

It is great to see more successful replications going on.

If someone were to post a quick video of doing the windings, I believe more would join in.

Thanks to all that are contributing to advancing the understanding!

IndianaBoys

I do see that having a quick video of winding tech. would help a lot more people get this done without frustration and the more replications the more people see this, the faster the world will change.
This reminds me of the 100 monkey story where 100 monkies lived on an island and believed that bananas were not good to eat for monkies. One day a large trunk rolled up on shore and aall the monkies came to see what was inside. After opening and seeing the bananas the elder said that it was a nice box but it was a waste because monkies did not eat bananas. Later that week one small monkey snuck down to the box and tried a banana and liked it so much that he started sneeking down there every day. After a while other young monkies saw what he was doing and told him to stop as monkeys did not eat bananas. He told them to just try one and thay did and liked them. Every few days more and more monkeys found the group and the same thing happened but all were told to mot tell the elders because everybody knows that monkeys dont eat bananas. This went on untill one day there were 50 monkies at the trunk site. Wondering where all the other monkies were the elders followed them to the trunk. Since there were so many monkeys eating bananas, there was little talk befor all the monkieys were eating tha bananas and to this day everyone knows that (monkeys eat bananas).
What this story shows is that the whole of thought will change only when 50% of the people know and are doing it. Replications, Replications, Replications. Build them, show them and teach as many who will learn to make them. Then and only then will all of mankind have it. Untill 50% have it there will be problems as everybody knows that we use AC current and spend our money and health unwisely. Humans do not use Free Energy.
Dana

[sebosfato]

Tomorrow morning i'm going to buy some motors to try this... I found great connection to what is claimed in 1975 patent N°3,013,004

Rotary transformer generator motor Machine that increase power output x power input...

[IndianaBoys]

Tomorrow morning i'm going to buy some motors to try this... I found great connection to what is claimed in 1975 patent N°3,013,004

Rotary transformer generator motor Machine that increase power output x power input...

Sebosfato,

I think you mean patent No 3,913,004

http://www.rexresearch.com/alxandr/3913004.pdf

Thanks for posting,

IndianaBoys

[LutherG]

Hello Brad,

You just wind it as winding a straight through Coil...no matter what paths over the core you have to follow...Understand me?
Meaning that a continuous Wire wound will render at start , let's say an N projected toward Stators, and the other side ITS South projected also outwards...
I think that getting distracted from Cores-Poles Config's get you guys confused, so FOCUS on your wires first, and their direction to follow.

The other thing is to MARK YOUR START WIND PRE-CHOSEN COMMUTATOR . Because once you start turning it, it could be a tendency to confusion...


Regards


Ufopolitics

Hi UFO,

Would it be possible to film the entire winding of one of the little RS motors from start to finish? From reading the posts here, it seems there is still some confusion as to how to wind the coils... I think once we see it we'll be able to apply it and everyone will be doing it in the same consistent manner...

I'm sorry to add more to what you are already doing for everyone... but this seems to be one of the most critical points to get correct...

Thanks for everything!

Cheers and best regards,

Luther

[sebosfato]

Exact! thanks for the correction...

I guess what happens is that the greater the load at the ac part the the greater is the imbalance between emf and cemf... Is that so?

[Turion]

I will film winding mine, and then if it works, I will post it. If it doesn't work, I will just pretend I never got around to winding it rather than suffer further embarrassment by posting how dumb I am. If somebody beats me to it, so much the better for all of us.

Dave

[wonza]

I will film winding mine, and then if it works, I will post it. If it doesn't work, I will just pretend I never got around to winding it rather than suffer further embarrassment by posting how dumb I am. If somebody beats me to it, so much the better for all of us.

Dave

Lol, I hope you're successful! I really could could a video too, I'm not 100% sure on how to wind it yet.

[prochiro]

Turion

I like your way of thinking. But, I hope it works. We all need to do it all the same way, fast, easy and learn how to do all types of motors.
Dana

[IndianaBoys]

Picked up 3 of the Radio Shack Motors 273-256 today.

RadioShack® Super Speed 9-18VDC Hobby Motor
Model:273-256 Catalog #: 273-256
RadioShack® Super Speed 9-18VDC Hobby Motor - RadioShack.com

30 gage red magnet wire:
315-Ft. Magnet Wire Set : Wire Sets | RadioShack.com

They only had 3 motors on the shelf.

Said when they sell 3 that is the reorder point.

Also said it was a slow seller.

Just letting others know they may want to plan ahead and get some motors on order now. As this info spreads and easier details of a how to video are put together demand for these motors will likely increase and longer lead times can be expected.

UFOPolitics, have you given a specific name to this Radio Shack motor build now that it has been born?

IndianaBoys

[b_rads]

Thanks for the help

@all,
A big thank you to all who have responded about the coil winding. The responses have helped and think the light bulb is starting to come on. A video would be most helpful, I agree. I want my build to be successful and see the kind of results others have experienced. Yes, I picked up my motors at RS today and they told me the same thing, my store will be reordering after my purchase today. This is going to be a fun weekend.
Brad

[bbem]

Windings

[QUOTE=Ufopolitics;201465][IMG][/IMG]

This is how I understand the windining, correct me when I am wrong:
The picture is a topview of the rotor with magnets.
Attach wire to the upper commutator at P1 and wrap magnetic wire 25 times through holes marked P4 and P1 in the picture, do not cut the wire, and wind 25 times (same direction as previous coil) through holes marked P1 and P3.
Do not cut the wire and attach it to lower commutator at the pole exactly opposite to P1. Cut the wire. Total wire resistance should be between 1.2 or 1.6 ohm.
Now start at P2 through holes (25x)P5-P2 attached to holes (25x)P2-P4 attach cable again to lower commutator at the opposing pole to P2 etc.
In total you make five V-shaped (two-pair serial) coils.

Bert

[JohnStone]

Hi Ufopolitics,
thanks again for your sharing! You offered a procedure I never dared to expect to experience in my life!

Regarding translations:
I saw too many poor translations on youtube because some are good in translating while others are experts in vids. I.e. I can provide quite good translations in German but my only expertise in vids is starting and stopping them.
My suggestion is to assign numbers to the individual pragraphs in a specific vid and post them here. Translations provided can be forwarded to experts in video processing. Because of the reference numbers those can provide translated vids even if they do not understand the language.
rgds John

[Ufopolitics]

Hello Dear Lamare

May I suggest to take it a littlebit easy with the translation of the explanations?

Quite frankly, your explanation with the Witch idea sucks. Now please don't take this as an offence, but it is important to get this right before you try and make it go viral.

Hello Dear Lamare,

First, please allow me to express my many thanks for all your fine compliments to my work.
Second, please allow me to tell you the description as how a Magnetic Field Develops in a Spiral Shape is excellent and beautiful, and, as a matter of fact, I do think of reproducing it in Three Dimensional Transparency Dynamics Graphics in a near Future...after We All take care of the "Main Priorities" as is get on with the Reproduction and spread of all the knowledge I want to share here and other places...

However, I will use it, to show it "Versus" the way I conceive it is based according to all my Lab Work...I have felt this force, this interactions, with my own hands...and pieces of steel bars...for hours, tryng, like a "Blind Man" to feel its structure and dynamics...

I have still to disclose a Method where Permanent Magnets are not required for this Systems...either, a Massive Laminated "Bulky" Steel Core...and still obtaining a very, extremely robust Magnetic Field Stators Arrangement, that besides rendering their job as Stators...We get Radiant Energy out of them galore....through my First Thread here...And the thing is...Dear Lamre, this Fiberglass Core, very light that I have built...is composed of ONLY ONE SINGLE COIL OF WIRE across the Armatures...and, to "Top it Off", its Magnetic Fields as conceived by "Classic Physics" are supposed to project the Maximum Strength towards the ENDS of the Coil...Well, I am sorry to tell you...They DO NOT project "Outwards" the Heaviest and more Robust Fields...THEY ARE RIGHT IN THE CENTER OF COIL, My Dear friend.

To the Point that ANY ARMATURE, SYMMETRIC or ASYMMETRIC that We Slide inside that EM Tunnel, and supply a signal for switching On-Off, either through Brushes or Infra-Red Commutation Systems (Coming Soon Guys)...WILL SPIN AT INCREDIBLE RPM's AND POWER...while it Outputs a great deal of Energy as my Original Coil Set-Up with Two small ultra-fast diodes...Besides (if it is Asymmetric of course) it will also FEED through this new set here...the dual Commutation Systems Output.
Now, the fact of making a Stator based on Composites, light weight, and just Copper wire (for now, till we develop Carbon Fiber Coils) Carbon is way cheaper than Copper...
This fact, makes this machines "scalable" to Any desired size, according to demands/requirements that the consumer requires...

And Dear Lamare,I love"THE WITCH", and I am enjoying (not so much YET) to set this OBVIOUS CONSPIRACY, and NOT SAID only by ME, but from many, many others, like MR. TOM BEARDEN, who I feel great, great admiration for...as many more...IN THE WORST RIDICULE That this Crippled Science HAS EVER GONE THROUGH, TO KEEP US SLAVES OF OIL FUELS AND NUCLEAR FOR 130 YEARS...

Therefore let that "part" to me...remember my "Last Name" is...Politics...

I leave you a phrase from the brightest Scientist EVER, that was a Victim of this Scientific Mutilation, Suppression and Seizing, and Condemned to Die, in the worst poverty ever, and Ostracized like it should HAVE NEVER , EVER HAPPENED in the Story of Mankind...



"...It is not a dream, it is a simple feat of scientific electrical engineering, only expensive-blind, faint-hearted, doubting world!...Humanity is not yet sufficiently advanced to be willingly led by the discoverer's keen searching sense.But who knows?
Perhaps it is better in this present world of ours that a revolutionary idea or invention instead of being helped and patted, be hampered and ill-treated in its adolescence-by want of means, by selfish interest, pedantry, stupidity and ignorance; that will be attacked and stifled; that it pass through bitter trials and tribulations, through the strife of commercial existence. So do we get our light. So all that was great in the past was ridiculed, condemned, combated, suppressed- only to emerge all the more powerfully, all the more triumphantly from the struggle..."


Nikola Tesla (At the end of his dream for Wardenclyffe)



Regards


Ufopolitics