My Asymmetric Electrodynamic Machines

[jason65r]

Power supply idea maybe

Hi UFO@all

Thankyou for the video

Was looking for a power supply for my battery charger for lipo's found this in the RC Groups Forum.
feathermerchantrc.com
Could you use this?
Two mainframe power supply units to supply 24v/47 Amps. So could you wire up another one to get 36v/47 Amps. Not 50 amps but close.

Or just three of these for 36v/72Amps
IBM pSeries 1050W AC Base or Redundant Power Supply 39J5638 42R7854 | eBay

and for the Ultracapacitor Bank

Ultracapacitor Diesel Engine Battery Starter Booster Car Ultra Super Capacitor | eBay

and No I dont work for E-Bay

Cheers
Jason

[Ufopolitics]

An Old Issue

UFO / Tesla Motor Tests - YouTube

what this replicator did wrong ? This seems discouraging, hmm

Hello Grizli,

I will be up front with you...

1-I already explained/went over in several pages back about that video, the testing results and all related discussion to a $3.99 Radio Shack Five Pole Motor, as there is extensive literature about that Design.
So, that means I am NOT planning to discuss it now...

2-In a previous post you wrote about using a Car Alternator...12V 75 Amps?...to feed what?...spending 36 V to obtain 12V?

We have also discussed numerous times here about Alternator from Cars not being good prospects for testing nor obtaining good results...and could NOT be modified into Asymmetrical...many times.

It is obvious you are picking randomly info without a solid complete read/knowledge fundamentals of this thread and its technology main side...then making a post on such already "digested data" is just bringing noise here.

Therefore, I would please suggest... to keep reading more, enough that you do not keep repeating same old discussions at our last posts here, as all it does is create noise...

I'll really appreciate it

Thanks and Regards


Ufopolitics

[sampojo]

question to interdesign21 post 2809

Hello Sampojo

Thicker wire that the original allows for higher volts-amps management, and therefore stronger magnetic thrust and obviously greater watts intake.

In the 5 poles armature I winded it dualpentagon mode with 28AWG and some 45 turns/pair (remember that every pair has same length of wire, not same N of turns)

Cheers
Alvaro

ASYMETRIC WINDING v 01 Nov 2012.pdf

Thanks Alvaro, I imagine that this was 3-4 ohm per coil. I understand the first winding on the RS motor and somehow see the asymmetry there, but not so much on the pentagon wiring. Is one known to be better than the other? Did you fill up most/all space in the rotor?

Excitement is thick on this thread but plugging along at this level.

Time to learn the winding for me. I lengthened the shaft and doubled up the rotors, same amount of work so went larger, hoping to penetrate a little more radiant energy. I think I will use this as a generator. I guess in the asymmetric winding document, post 2250, I think the first RS 5-pole winding is showing some tuning. On page 8, the commutator gap is shown aligned with the armature split. In the attached thumbnail, I interpret that the red wire is attached to the front commutator and the blue wire to the rear. If wrong someone just shout it out. I think I mentioned the radioshack using green wire (30 ga), it is not, must be 26. On closer examination the red wire seems to match what was on the motor and one rotor had 9-10 ohms total, so I will shoot for winding 20 ohms same size, twice as much due to double rotor.

Maybe before I go Imperial 56 I will try to build something with some window motors coupled to a single phase inductive motor converted to a generator. Be nice if I could get a couple hundred watts

TIA! (thanks in advance

Joe

[prochiro]

@ All
Grizli, when you follow his history on this forum, has been bouncing all over the threads saying he is too busy to read anything and in general asking uninformed and off based questions and offering advice that reflects little knowledge of what is going on. I would suggest that anyone responding to his posts, keep this in mind. He has actually wasted the time of many others who are doing there own work.

Dana

[Lightworker1]

Many Congratulations -- Many Congratulations -- Many Congratulations

US, Canada, Australia, Germany, France, Argentina, Philippines, New Zealand, Spain, Malaysia, Poland; South Africa, Latvia, Netherlands, Indonesia, Costa Rica....


Hello My Dear Friend UFO
Many Congratulations on this successful completion of IMPERIAL ASYMMETRIC MOTOR Driving SYMMETRIC MECC-ALTE BRUSHLESS GENERATOR. On this auspicious day your experimental success means one giant step forward for all the humanity by your tireless dedicated hard-work and vision. Furthermore, you freely chose to share your work selflessly with one and all. The act of giving selflessly is an attribute of saintly souls. I hope this is the dawn of enlightenment the world has been waiting for over thousands of years. Imagine a world free of pollution, free of want, free of disease, free of disaster. Imagine a world populated with smiling, laughing, happy, joyous people--all radiantly healthy, all abundantly supplied, all loved and loving.

Today you also honoured one of our greatest scientist, “Nikola Tesla.” Even in spirit, today he is happy to see his dream becoming a reality. I wish you all the health, peace and happiness.

Couple of days back Dyann emailed me that my imperial ufo kit will ship out tomorrow (Friday). Looking forward to build this great motor.

Also, hoping to complete my dual pentagon goldmine asymmetric motor soon.

May be in the coming year we might see and get invited to extraterrestrial craft like this Pleiadian-ufo-craft.



Warmest regards
lightworker

[JohnStone]

Hi Folks!
regarding shipping the motor to international destinations:

It is advisabele to employ an US based mail forwarding service: i.e. shipito. (This is an example but no recommendation because lag of experience but there are plenty of them).

• You contract with the forwarding service for this single delivery. They host for you a virtual address in US.
• You pay to Dyann the motor added demestic US shipping fee (about 55 USD).
• She ships the motor to your virtual address in US.
• You pay the contractor for delivery from your virtual address to your local destination.
• You get the motor soon.

The contractor will ask for package dimensions and weight.
Weight: 41lb / 18.6 kg
Dimensions: 19" x 17" x 14" / 48.3cm x 43.2cm x 35.6cm
Example: shipito -> Germany = $121.09
JohnS

[iankoglin]

G'Day UFO my dear friend
I think your Video is awsome I have always believed you would do it.
You are a honerable humble person sharing your disclosure the way you do starting with little things so we could grasp the concept and then answering all the genuine questions put before you even when you must be able to see all the newbies to this technology really trying to grasp the things you explain to us .
I must say thes 2 forum lists are the most pleasant ones I have been associated with every one participating is eager to help each other learn

You are a definitely fine leader as can be shown by the decorum displayed by everyone here.
So thankyou for what you have done, rest up a bit we will all enjoy your continued work
I have already purchased a Mecc Alte generator in Aus and waiting now for the Imperial motors

Kindest Regards

[interdesign21]

Thanks Alvaro, I imagine that this was 3-4 ohm per coil. I understand the first winding on the RS motor and somehow see the asymmetry there, but not so much on the pentagon wiring. Is one known to be better than the other? Did you fill up most/all space in the rotor?

Excitement is thick on this thread but plugging along at this level.

Time to learn the winding for me. I lengthened the shaft and doubled up the rotors, same amount of work so went larger, hoping to penetrate a little more radiant energy. I think I will use this as a generator. I guess in the asymmetric winding document, post 2250, I think the first RS 5-pole winding is showing some tuning. On page 8, the commutator gap is shown aligned with the armature split. In the attached thumbnail, I interpret that the red wire is attached to the front commutator and the blue wire to the rear. If wrong someone just shout it out. I think I mentioned the radioshack using green wire (30 ga), it is not, must be 26. On closer examination the red wire seems to match what was on the motor and one rotor had 9-10 ohms total, so I will shoot for winding 20 ohms same size, twice as much due to double rotor.

Maybe before I go Imperial 56 I will try to build something with some window motors coupled to a single phase inductive motor converted to a generator. Be nice if I could get a couple hundred watts

TIA! (thanks in advance

Joe

Prochiro: I agree 100% with your words, as a matter of fact, I was about to ask Grizli to show some kind of politeness, and avoid us the noise, I think this is a researchers forum, not an entertainment chat.

Joe:
You are welcome

yes,in my case 3,5 ohm per coil pair.(dual pentagon) and yes, it was filled, had to press down the wire while winding.

I also made one with two printer motors assembled together like you, (8,6 ohm/pair) and I observed that as magnetic drag was also doubled, all the parameters went also high (more than double ). I experimented with different inputs, but I have to revise my measurements as I do not trust my own accuracy enough

In the diagram from page 8, the blue wire starts at input(motor side), and means it generates a N pole projection outwards,it continues as red,meaning south pole projection, and ends at output (Gen side.)

Hope this will clarify something for you, if not, please don´t hesitate to ask again.
If somebody here finds I´m wrong, please say so.

regards to all

Alvaro

[Wm.Joe.Hill]

Greater Success

Ufopolitics,
Congratulations on your success and I wish you even more success in the future.
There may be many opportunities manifesting at this moment in time.
Would you be adverse to people talking to motor manufacturers concerning the development of UFO type motors. This development may be for many different reasons; with one of the reasons being potentially greater performance for a given size motor. The ability to experiment with the potential of gaining extremely high efficiencies could also be used as an additional selling feature.
Existing motor manufactures may be interested in advancing their product lines; and many people (potential customers) may be interested in experimenting with the potentials of this motor technology. This type motor appears to be at least equal to current technology; and it appears to have the potential to significantly exceed the capabilities of current technology. Motor manufacturers may be interested.
If enough people become involved, the men in black may simply be overwhelmed by the sheer numbers of people working on this technology. The use of open source development may massively benefit everyone with good intentions.
There may even be a demand in locations throughout the world for courses on this technology; and these courses may be most effective if they are taught by people with hands on experience.
Best of luck,
Joe

[JohnStone]

@ALL
Please stay patient. This technology has great potential but is still not ready for mass production. Usually you need:
20% of total effort to get 80% done.
80% of total effort is necessary to finish the 20% left.

• Manufacturers are not interested in open source because they open a door for ALL competitors instantly. Smaller motors will be sold cheaper. So they will open their door for less turnaround.
• Battery manufacurers are not interested because they will sell smaller batteries only for electric vehicles.
• Gouverment is not interested in less taxes.
• Roulers earnig on oil and gas are not intersted to deminish their future.
• ...

This is the attitude of money. This technology is a nogo for them. Review the history of free energy? Did any inventor get the idea running by help of money? Did any earn money? Did any help protect the globe?

The only enemy of self content and selfish attitudes is to overtake them apart their focus. Let those people in poor countries start their own replications and maybe have own startups before big money conquers this technology. Poor countires often have no elicited law system prohibiting clean solutions.

Let the poor people get their energy in rural sites in order to earn their life from the work of their hands. They shall not be part of worldwide rural exodus.
@UFO: Don't be sad of these thoughts. We are not responsible for past generations but every day we get new chances in order to meet our responsibility.
JohnS

[jeffy39]

congrats

@ UFO, congrats, as others have expressed. I'm not eloquent with words.
My 2 Imps. should arive any day now.
Would 'UFO' (literally) = 'Un-Fathomable-Opportunity' ?
Best to all, jw

[Tinmanpower]

Hi Tinmanpower,
you are right with your request and many others feel with you. Of course such measurements will be done all over the world - including me.
But please let Ufo recover first from his excessive effort during recent days.
We will surely get our proof - soon.
rgds John

I see much celebration going on here,and many people spending there hard earned cash on kits.
I am more than happy to let UFO take his break,but as he has clearly claimed an overunity device-i need to ask again
Can some body(anybody) please direct me to the video that clearly shows an overunity device.

To make such a significant claim as an overunity device,surly there would have to have been accurate measurments taken to proove this?
But from what i have seen in the last video that UFO showed,no such measurments were made.
The best i and others could make out was 36 volts at 40amp's plus(as it peged his meter)and 1000 watts out-thats if the full voltage was accross the incandecent bulb's?
So 1440= watts in and 1000 watts or less out???

If UFO has made these accurate measurment's,then why wernt they presented in the video?

It just seems that every one here is celebrating on the word of 1 person,with no accurate measurment that as yet have been seen.

I do congradulate and comend UFO on his endevor,but when you make a claim like this(overunity)you need to be able to clearly and accuratly show it.

Has anyone asked UFO if the kit's they are buying are an overunity device?

Many of us have seen all to often the cry of overunity,only later to be disapointed.

Many may think i am out of line with what i say,but please know that i am hopeing as much as anyone else that UFO has succeded in bringing to us an overunity device.

But wether it is UFO,you or myself that has a device that is overunity,we had better be able to back up our claim's-even more so when people are paying hard earned cash based on your word.

[Michelinho]

Congrats UFO, you have done a GREAT job of scaling up the UFO motor.

Hi Tinmanpower,

All of your questions have been ask since the early part of this thread on smaller motors. Why clutter the thread with redundant questions, UFO knows what he has to do and I am sure he will comply with all the constraints necessary. The video as mentioned by UFO is a PREVIEW that he imposed upon himself when he set the date of the release.

Do like all the watchers and wait as asked. If we can wait, you can surely do the same. Thanks.

Take care all,

Michel

[Tinmanpower]

Congrats UFO, you have done a GREAT job of scaling up the UFO motor.

Hi Tinmanpower,

All of your questions have been ask since the early part of this thread on smaller motors. Why clutter the thread with redundant questions, UFO knows what he has to do and I am sure he will comply with all the constraints necessary. The video as mentioned by UFO is a PREVIEW that he imposed upon himself when he set the date of the release.

Do like all the watchers and wait as asked. If we can wait, you can surely do the same. Thanks.

Take care all,

Michel

Michel
My question is not redudant at all.I have asked this question after UFO has made the claim of an overunity machine
Have you seen the test results that prove this claim?If so please send me the link,and then i will no longer have to ask the so called redudnant question.
If i made such a claim,i bet you would be asking me for the proof.

[Michelinho]

Hi Tinmanpower,

This is post #35 of this thread, that is pretty near what you are asking now, read the thread and you will see your apprehensions have been posted before just like UFO told you.

This is t

UFO,
I have looked at all the videos and seen what you did with your small RS motor. I have also rebuilt several motors according to Dr. Lindemann's instructions for how to best wire a motor, so I have some experience with this. Two years ago I built something very similar to what you have shown us here, with the help of a friend, and from what I see, what you have appears to be a simple "Buck Boost" circuit.
Buck–boost converter - Wikipedia, the free encyclopedia

If it is NOT, the proof would be to compare input voltage AND AMPERAGE with output voltage AND AMPERAGE. If you are getting higher voltage while maintaining the same amperage, you have something. As yet, I have seen nothing in the videos that indicates what the amperage is going into your small motor setup nor what it is producing. I would love to see some video of THAT!! I hope you can prove me WRONG.

Turion

Hope this clarify my previous post.

Take care,

Michel