Gerard Morin Energy

[mikrovolt]

The motor alternator video posted by Mikey is good example of smart components.
The caption reads:

Tests with Etek 48VDC motor "as motor" and "as generator". I used Kelly controller 48V -- 400A, WEG AC motor -- 1,5 CV, ABB drive and cycle analyst. The Etek motor is very good motor and generator in my tests. This motor is very interest in projects to electric vehicles to regenerative braking.

48V Brushless Controller KBL - General Brushless Controllers(12V-48V)

https://www.electricbike.com/etek/
I think some of the best designers in the world are making it happen with the e-bike platform.
Need more enthusiasm to promote more design hobby with the new parts available.
Those guys do good, have honest expectation they contributing alot and the parts
keep getting better.

[BroMikey]

48V Brushless Controller KBL - General Brushless Controllers(12V-48V)

https://www.electricbike.com/etek/
I think some of the best designers in the world are making it happen with the e-bike platform.

Super links.

Here is another update soon to be another, just a peek 4 now.

https://www.youtube.com/watch?v=J8EG74vvWDM

[BroMikey]

Motor Generator using pancake coils also the magnets are added

to conventional motors and to the motor that generates as well.

https://www.youtube.com/watch?v=ORDYdNWjQzk


https://www.youtube.com/watch?v=UCCnN6PNKhs

[BroMikey]

Here is DOG-ONE using a simulator to draw attention to the

importance of tuning. Tuning motor coils or Motor Generators

with caps. Look at the wave shapes and phase.

An out of phase current to voltage 90 degrees is the place

to start. Get the phase angle away from conventional

phasing so reactive power can run your loads.

Thanks DOG.




https://vimeo.com/83003669

[Belangers]

Those who have the gaul? Qualified would be the word. Balls or gaul will kill you.

I just saw a comment stating that this works.. Here Are My findings... It really does work, but, the transformers are not to be grounded, so, I would at least think that those who are smart enough will do so as a professional would install these transformers where people could not touch them, especially children. These transformers should be mounted to a pole where they can't be inadvertently touched. These units not being grounded have an arc discharge from them if they are touched.... This could lead to disastrous electrocution if touched. To ensure a safe operation of any transformer, First, you need to make sure the transformer runs at their rated output and input voltage . This is difficult to do when feeding them with cold electricity, but, feeding cold electricity into them doesn't cause a fatal condition as the amperage during the failure or shorting of the cold electricity will not cause quick and violent discharge as conventional overhead lines would.. However, this could be obtained if not connected correctly, so, I would advise not to touch any high voltage transformer if you are nor qualified to do so.

I am a licensed high voltage contractor that works with medium and high voltage systems for a living. Safety is my number one concern, especially for those of us who experiment with the unknowns of the free energy communities. High voltage transformers can explode and kill those if used in a manner that is not how it is intended to be used. They are not meant to be used for experimentation, so, I highly advise that these transformers are only used in a safe lab that has been built to withstand explosion, reduce the risk of shrapnel and fire from the flaming oil they could release when arcing. People who use them not knowing how they operate may get electrocuted beyond all expectation, lose limbs, or even worse, die. Most electrocutions in the high or medium voltage industry end up fatalities.

If somebody drives a high voltage transformer with higher voltages than they are rated for, corona discharge could lead to a massive failure.
When one uses a generator to drive a transformer as a step up unit instead of a step down device, it is critical that the voltages to drive them are maintained correctly. If we drive the center tapped 120 volt coil with 240 volts, we can destroy the coil and cause a massive fire if the amperage driving it is high (10 amps or higher). The transformer's coils are only built to withstand so much high voltage. If we drove the 120 volt coil the wrong way (simply by connecting the coil of the secondary voltages the wrong way), the high voltage side will double it's voltage, exceeding the rated high voltage it's meant to operate at and possibly cause a devastating explosion.

A WARNING TO THE UNEXPERIENCED: High voltage bushings do not need to be touched to become electrocuted, we can get too close to them causing electrocution just from getting too close. There are high voltage clearance distances that need to be followed per NEC regulations. High voltages are nothing to play with.. Many people in the electrical field get killed by backfed generators driving transformers into the overhead lines during storms due to the fact that the generator was connected unlawfully, without an interlocked or an automatic transfer switch that opens and keeps it open while the power companies feed is de-enrgized. A Back feed from a generator will energize the circuit leading back to the source if a transfer switch or lockout isn't correctly installed, this is why a licensed professional should be installing the generator and transfer switch for you as indicated by the NEC code book and US Law.

The energy created by a generator has the ability to kill people. If we take a 7500 watt generator and backfeed a 10kVA transformer, the transformer will nearly be maxed out when energized, creating 240vac at 31.25 amps. This will make .94 amps at 7970 volts on the primary transformer's bushing. The transformer will easi;ly have the capability of killing a lineman, as well, will backfeed other loads such as homes which may be the only load on the generator other than the home the generator would normally operate which may not overload the system and allow it to keep operating, causing a massive danger that could kill anybody touching the primary electric lines.

People that are not experienced usually do not have a clue as to how transfer switches normally operate or safety precautions to be taken when installing. Linemen use hot sticks made of fiberglass to connect transformers with tap wires and hotline clamps while the overhead circuits are live. They are also required to wear rubber gloves and sleaves rated for 20kV at any moment they fly their bucket trucks. This safety procedure is called "Ground To Ground Rubber" It is a protective safety rule that would give a lineman the protection necessary to eliminate electrocution provided their rubber protection has been proven not to have holes or voids in them. These rubber protective sleaves and gloves are tested regularly (every 30 days if worn and used daily).

If one takes their lineman pliers and connects the live high voltage wiring thinking the plastic covering on the plier's handle would protect them, they probably wouldn't be around very long to talk about it since the high voltages could jump right through the insulation since it isn't a good enough dielectric to insulate from electrocution. This separates the experienced from the inexperienced. I have witnessed low voltage electricians taken by ambulance from jobsites because they were not trained for high voltage safety and literally connected their digital voltage meters or rotation meters to a high voltage connection on a motor and it exploded in their face, burnt hands off, or the fireball melted their skin from their face. This is the important factor that could lead an innocent researcher into a disaster that could either affect them for the rest of their life, or kill them on the spot.

High voltages at 1/5 to 9/10 of an amp will still kill people since the wattages are still extremely high (V x I= watts)

I do not recommend that anybody try the transformer experiment at home using an amperage driven circuit from your home outlets, or, from any generator unless you are a qualified with the safety of high voltage systems, are currently a qualified high voltage lineman or a qualified medium & high voltage cable splicer that's got the experience to safely do any of this.

I have attempted to collect data to build the mathematical equations as Watt & Ohm have done for cold electricity, but, the formulas do not apply in the same manners as resistance works in an opposiong manner, so, we need physicists and other researchers to assist us and work to create a mathematical model for cold electricity.

To attempt this with my research, I have used Karl Palsness's Hairpin Circuit to output cold electricity on a higher than normal level to test and verify that resistance works in the opposite manner. I was successful, but, other formulas of watts and ohm's law are also inconsistent, so, we need to create a completely new chart for cold electricity. Whether or not science agrees, Cold Electricity is very real and it does the exact opposite as Karl Palsness said when we wire in light bulbs with a conventional incandescant filament. The circuit energizes a 40 watt light bulb extremely bright and with higher output wattage than a 100 watt bulb.

The system seems to thrive and power these bulbs better when connecting with 40 awg copper magnet wire instead of 16 gauge solid electrical wire due to the fact that the circuit pushes more power into higher resistances. Where I used the 16 gauge, the circuit did not illuminate at all. I am also able to energize the 40 watt bulb so bright that I can't look at it (wired at 100 feet away with 40 awg magnet wire). The high resistance of the wire allows the power to flow through it while the circuit can also be completely short circuited and still allow the energy to flow. Conventional electricity wouldn't do this as the wire would burn from the heat released from the high resistance of the wire, or, the circuit breaker or fuse would pop.

The 40 awg wire doesn't even get warm while the bulb creates so much heat that we can't touch the glass. We could take the bulb, dunk it in water, and it still operates. This includes immersing the connection in water and we are safely able to touch the water or the bare wire with our fingers without electrocution. This circuit outputs high voltages that arc across a 1" spark gap, so, we have extremely high voltages present and the danger is extinguished in the arc gap as the amperage that drives the circuit has been eliminated, jumping through the air at the spark gap, reversing it's dangerous ampacities by discharging the arc and collecting the energy for continuous output through the doorknob capacitors.

We could drive the circuit with conventional power and still obtain an output at very high resistances that do not increase the power used from the circuit's input. The input remains the same regardless what we connect to the output, but, there is a lot of research necessary to prove this. The conventionally designed high voltage instrumentation needs to be used , however, they must be designed for the use of cold electricity and calibrated to this type of energy since it works in a manner inconsistent with conventional electricity. Since electrical formulas are not consistent with cold electricity, all types of electrical metering would be inaccurate to measure the cold electrical system until physicists come up with the new mathematical model so metering could be sopecifically made to measure cold electricity..

Before anybody states this is not a true overunity system, please be advised that we have proven that we could get more out than we could in, but, since the conventional meters used to read standard electric readings would not be accurate, there is nothing other than the use of resistive loads to prove the theory of overunity as we need to measure the system only using calometric meaures at the moment. Since heat isn't generated in the same manner with resistances, I don't feel it is accurate to say even calometric measurements are even accurate, so, models would need to be come up with and specific tests to verify that cold electricity functions the way we have been seeing, as well, some sort of mathematical system to coincide with our findings. Nobody could really prove or disprove the system yet until all tested componentry would coincide with research to prove exactly what it does. It is too new, or should I say too suppressed to state otherwise at the moment. We need people to jump aboard and submit their findings for all tests to prove exactly how it works.

The dangers of the transformer experimentation outweigh the advantages of overunity unless those of you who are experimenting with the transformers utilizing amperage driven electricity from generation follow the correct safety precautions when doing so because people are going to end up dead or in the hospital with a few less limbs if they don't follow overhead line safety procedures since the line currents are extremely dangerous once we step up low voltages to high .

PLEASE BE EXTREMELY CAREFUL & PLEASE SEND ME A PM IF YOU GUYS AND GALS HAVE ANY QUESTIONS RELATED TO THE SAFETY OF THESE SYSTEMS.

[DavidE]

Belangers

Excellent post.

Warning heard loud and clear. Opportunity heard loud and clear.

[Dupe]

Very sensible advice

[BroMikey]

Very sound advice, the inexperienced should never run without

a transfer switch or good rubber. I don't mean to be rude

here, but this experiment has nothing to do with a set of

very large chandeliers as a prerequisite for good OVERUNITY

results.

We have looked at the videos where folks are charbroiled to a tree

or a pole so this point has been thoroughly driven home

repeatedly.


I agree if people are going to dump raw amps into these pole

transformers and touch their tongue to the circuit they should

be expecting death. I also agree that a fiberglass stick be used.



What I disagree with is that everybody assumes that this

experiment is directed at the kiddies and somehow after

reading this thread you have concluded that the warnings

are lacking.


Now, let's get away from this silly notion that the goal

of this experiment is meant to exceed all of the coil limitations.

Let's talk about what has been said.

Goals of the experiment

(1) feed the 120vac coil with 120v pulsating DC at a fraction
of the coils capacity.

(2) Never leave an open path for the HV coil to randomly jump
just wherever is wants to, always connect the ground to the ground
from transformer to transformer.

(3)Always connect the HV wire from one transformer to the HV
wire on transformer 2.

In the original video a 50kva pole transformer capable of 200 amps
120vac with 20 amps. Also that the type of ac feed into the 120vac
winding is not a conventional waveform and resembles RF.

That said, no one should be assuming right off the bat that investigators
are about to experience the grave, for trying the experiment.

Granted someone will read all of the information and spend many
thousands for transformers? and start doing wild HV experiments?
that I have no control over, that is their problem.

He is a stupid fool if he does, because as has been pointed
out, most folks have no business playing around with stuff they
know very little about just because they have the money to do it.


Also on another note a single transformer might be feed HV
to the HV coil to produce 120vac many other ways than with
the use of another pole transformer.

Insulation breakdown of coils should always be a consideration and
as I said before the goals never suggest that this be done. The
object is to use far far less not somewhere around the average
rating.

If I am talking to a wall, it is not my fault people don't listen.

At present Gerard and many others are using way less on the
input than the output offers but ways to loop the system is
more complex.

Yes I agree people with the money to the tune of say $20,000
should not try this just because they can afford it. If money is all
they have then I suggest they not play around with this as some
sort of wonderful beginner lesson.

This is real power in and out and like we have stressed, one
dumb move like leaving an open ground might kill you.

SO stay away if you are a beginner, this is for those who are
not only all grown up in the field of HV handling but also
those skilled in the art of invention, that does not come over night.

[BroMikey]

Gerard Morin device test 2 - 4 bulbs lit



[VIDEO]https://www.youtube.com/watch?v=5IQvXNFPt1o[/VIDEO]

[VIDEO]https://www.youtube.com/watch?v=Y63kJSkizaI[/VIDEO]

[BroMikey]

Pole transformer controls

[VIDEO]https://www.youtube.com/watch?v=A3L880enaNI[/VIDEO]



[VIDEO]https://www.youtube.com/watch?v=i7N2iMpOE7I[/VIDEO]

[BroMikey]

Totally insane complete fool

[VIDEO]https://www.youtube.com/watch?v=yvMEMvAswdM[/VIDEO]

[BroMikey]

This gentlemen has a brain, not like the complete dill rod

in the last video.

[VIDEO]https://www.youtube.com/watch?v=cfsiAFdRh-g[/VIDEO]

[Dfortune]

Latest video from Gerard

Enjoy

https://www.youtube.com/watch?v=56NQoUeslSU

[Gerard_Morin]

I'm going to upload part 2 tonight..
It's a shame I did not have the bulb experiments filmed.. but I was testing and re testing so that the video would have no hiccups.

Another one will get done soon.. But I had to leave Ontario Lab.
Finishing the generator back home now.

[BroMikey]

I'm going to upload part 2 tonight..
It's a shame I did not have the bulb experiments filmed.. but I was testing and re testing so that the video would have no hiccups.

Another one will get done soon.. But I had to leave Ontario Lab.
Finishing the generator back home now.

U da-man Gerard

Thats right nobody questions the master or they get a stone

wall if they do. Our society is programming people to be drones

that can follow the commercials on TV, be all you can be, be a

truck driver, be a welder, be a puppet, be what we say, be a medical

techy, whatever fits into the global controller plan. And of course

all of the Indians just fall over like ducks doing everything perfect

to make the world go round in the way they are told.

Good video Gerard, no I am not religious in the forms we see today

but I need to be forgiven so I forgive, end of story.


Gerard you scared me half to death with your loose connection at

14,000 volts. I need you in one piece and this HV connection can not

have any corrosion or rust Oops.


You don't want to make that mistake twice and grab the can

to shut it off, no, no .no


Poor little guy McCulloch can be put in the sheet can, but we

want to keep you around long enough to squeeze out all of the

teaching joules so we can come up to your understanding to

invent something really useful.


After that you can go ahead and kill yourself. No just joking

around Gerard you know me. Somebody said you could make that

Bedini motor levitate. Some lucky sucker otta try that

experiment. No but really that Bedini motor has kept the dream

alive for 40 years and that was the motors job. It charges batteries

better than any machine on earth and it was never intended for

anything else.


To bad the McCulloch got a smoked winding, but remembered you

have others at the house. Yeah sitting around the coffee table

in BC has gotten you noticed worldwide and I can always tell

when a person has a gifted personality to talk to people.


You got it Gerard. Next time clean those HV connection bolts

well and if you want to maybe use a bolt with a special coating?


So oxidation from arcing can not build up, I don't know what they

use, it's something for that 14,000 volt range.


Good stuff about Gov programming and the harmonics, sounds, RF

all that stuff kicking around in your head. I know that HV cap is

probably a common value and I will listen again to see if the

micro farads are given. Is this cap a .01 Uf???


Also when you get going on the experiment for me(BroMikey)

and Hitby, show us how the cap makes the OU better with it and

how little the OU is when the cap is removed.


Once this is done, I am going to buy some pigs.

I also have a dozen washing machine pancake motors and I think

these maybe can power a pig?


Glad to see some of these guys picking up the tab for someone

as cool as you are Gerard. Just a regular guy doing his dead

level best to drive the point home.


Remember this Bedini did this to the best of his ability but

he was threatened years ago as well. When you have a lot

to loss it is easier to crack the whip on an inventor.


I am glad you are climbing the charts and hope you don't

make a mistake that is fatal. We are all routing for you Gerard

you are a man's man indeed, so don't expect a huge following


The money means nothing, it is like you say, gotta have a man

with enough intestinal fortitude to stand up against the brain dead

to shatter the spell we are under. I hope they don't hurt or threaten

you also Gerard. Just stay crazy like the one eye dog who you can

never figure out who just keeps coming back and the trolls who

have been castrated from birth, will run back to their trainers sitting at the

doughnut shop to ask for further instructions, because they won't know

what to do with you anymore.