Gerard Morin Energy

[bistander]

Redi-line generator

Here is another magnet motor generator running.



Published on Feb 1, 2014

The purpose of this Self Looped Generator proof of concept project is to determine what happens when you take 12v dc components (12v battery and motor) that produce 120vac and plug in a Kill-A-Watt meter to a CFL bulb. Then with the same power produced by the motor, plug in a battery charger to recharge the same battery. Then take a drill to see what kind of a voltage drop occurs and if the battery voltage is either sustained or dropped. The results are pretty impressive as a portable setup without any external power from the power company or fumes.


[VIDEO]https://www.youtube.com/watch?v=OsL4Fh1fVVE[/VIDEO]

The only thing remarkable about that is that someone could think there was free energy demonstrated. It is obviously an old Redi-Line motor/generator which has taken a serious hit. The bracket is broken, the faceplate is missing and it has been partially demagnetized. Besides the obvious reasons why self looping with a battery charger won't work, you can see his orange extension cord off to the right in one camera angle likely feeding his battery charger for his scam.

See this link for Redi-Line. Alternator Starter > Innovative Solutions > RediLine Generators

[BroMikey]

This guy can charge his cell phone with his. listen to his
wife say "Its slow" meaning when the plug connects to
the phone and charging initials the tiny motor/genny
RPM goes down.

Oops heres the video

[VIDEO]https://www.youtube.com/watch?v=YkgpTeeaeMY[/VIDEO]

[BroMikey]

All men have gifts and the desires they have to achieve
the end goal of any experiment is part of the gift. Where it
comes from no one knows, but one thing I will tell you is that
the gift giver is never limited by those who have just one.

There are 100's of gifts so get over it people. You will never
be just like the next person. Just relax and enjoy their gift


If we are to ever understand new ways to get the extra energy
come from wherever it may, we will need first a list of parts and
a teacher who can show a working example.

Spending thousands is not the mark of higher learning, unless
you can show it working. Another man may show his works on
hundreds.

But one thing is sure, without an advanced builder who has
already done it can show that the system design functions
as stated (If anyone really understands the endless chatter)
then followers will be far and few between. Let's face it most
people want to build something that has at least enough
left over power to light a bulb.

If any inventor of any system can show a working example
and does not hide the parts list, that man will lead the majority
of experimenters in that field.

Gerard has a heart to share and give, no hidden gimmicks, no
secrets just a willingness to help other understand COLD LECTRIC.


Well maybe we will call it GERARD LECTRIC

After 20-30-40-50-60 plus years no one can show an overunity
example, just endless builds that may or may not do anything, on
a find out for yourself basis. Let a dumb ash follow that.

I hate lies and trickery.That is what Gerard is saying.
His first unit cost $40 to build so this is a more realistic price tag.
Plus Gerard is not afraid of the camera.

Gerard is open and worth following, period. Marc B. also is a good
experimental researcher to follow. Marc understands Gerard's systems.

We are still learning, trying to find just one good example, you and I
need this talk about Tesla's Key. Thanks Gerard.

Here he is "IT'S ME AGAIN"
Great inequality exists in the world today, sheet on the little man.
Down where we live guys.

A tough dude who talks like a trucker. Great frustration.




The Key Element of Tesla's Discovery

[VIDEO]https://www.youtube.com/watch?v=dK9FBwJfrmo[/VIDEO]


[VIDEO]https://www.youtube.com/watch?v=HV0MH8U3sS4[/VIDEO]


[VIDEO]https://www.youtube.com/watch?v=1rIGClvjBp0[/VIDEO]

[Belangers]

Morin Transformer

Hello 10K

3 things.

(1) washer pump generator energy experiment video's


(2) Pole pig HV energy multiplication


(3) Larger washing machine pancake motor generator's


I guess it depends on which one we focus on. In my understanding
of Gerard's work on (1) we see several men making advances using
this type of energy effectively and so it is with so many available
projects on the web.

Next is (2)

The information became available through MARC B. and we saw that
this phenomena has been witnessed by others tho it maybe to dangerous
to foster a group of trainees to learn as we might only be recruiting
the unaware for a death sentence.

Conclusion? Yes it has been done and is repeatable.

Next is (3)

Gerard is now working on another motor generator combination that
has been much harder to complete. In this instance the setup needs
more than just a simple motor coupled up to a simple motor acting as
a generator. It requires expensive controllers and I say controllers
plural because everyone is struggling to find the best way.

Pulse DC or a modified sinewave or a pure sinwave? And then most of
what I can find is running at 12vdc to 36vdc that is inexpensive. Like
we see on electric E-bikes and scooters. Some as high as several hundred
dollars.

I know, I work on these washing machine motors for a living and you can't
find an easy circuit to power these pancake motors at the 120 volt AC
input rating that they are designed for.

Some are clipping the windings and paralleling to lower the voltage while
others are going to a large corporation to get a custom made device. This
is what Gerard is going through at the moment. How do I know? Because
I have been through that dress rehearsal many times. So I can simpathize.

Recently Gerard has come out in video stating that is simply showing
his progress on his motor generator designs and welcomes others idea's.

Let me know if I have not answered maybe a more specific question you
might have had. To summarize, motor generators are and have been a
popular way of creating reactive power by tuning each individual motor
and motor acting as generator's coils. Matching or adjusting speed, voltage
that limiting current to get a resonance of one form or another.

Gerard has his hands full finding what he needs to complete what might
have looked like a rather reasonably reachable accomplishment so we will
see.

I can see a lot of things happening here and how folks can easily discredit claims by many, especially of how the transformer tests were shown by Gerard to output "overunity" as he shows. I think the largest dispute folks have with it is the fact that he shows the devices working without testing each device separately to confirm the devices literally use what is stamped on their labels. Power factor has a little bit to do with it, however, the theoretical approach of V x I is good enough for myself as it is always very close, and, much more believable than the stamped labels are. The stamped labels are a sales pitch for devices at best, especially for high powered stereos and the hammerheads who buy them that are in need of really loud music , so, we will not use stereos or amps as an example.

Let's start off and say I have a very valid test video that I'd like to subject a drill to the test and see what it's actual wattage is. It would be a bad device to use because inductive loads vary with power factor more than resistive loads, however, if the labeling was correct, it would be much more helpful for these tests, but, they are not. In most cases, these drills are rated much higher than what they use, and, it is for the simple fact that inductive devices can use much more load under strain when the power factor is not good, and, if they are good power factors, the load will be much less at start up, and, overall seem much more efficient, zippy, etc. I will also stay away from motorized tools for my test subjects, and, the overall best devices to use are resistive, but, bad choices are heaters and I'll tell you why.. They are sold with the sales pitch again to some of us looking for a heavier load to make it hotter for our garages, or, a lower and more efficient device to save electricity. The best device pound for pound that can be used for testing anything is a load box, (resistor box) that has been tested to verify it's within it's labeled calibration so we know what to expect. For smaller tests, normal resistors rated for the wattage we will expect to draw will suffice.

Gerard would have best been able to show his viewers without much doubt that he could run a resistive device , such as a stove element, or, a very high powered resistor to prove it is exactly what he said. If he had a 150 ohm resistor, we could all do the math to see what the outcome would be, making it at least a little bit believable. I think there is one thing or effect he did hav that did open our eyes.. That is the measurment from the laser thermometer. If I had the same response using conventional power, I would have stopped the test, however, I did not do so. I tested while my McCulloch generator ran for all of 3 minutes and was never able to test again on film, but, I did get a rather unusual response , and, I did get the output to multiply, however, it wasn't anywhere near the levels claimed by the stamped plates on his devices.

I did see the temperature hit -20 during the summertime on the HV bushing, then, I verified by getting the same reading + or - a degree by aiming toward the sky. When the conventional energy from my Briggs & Stratton generator was fed to the secondary terminals, then jumping from one generator to the next by the hv coils, the temperature reading was a standard reading of the actual bushing temperature, not negative.

By the time I reconnected to try to add more load and reconnect the McCulloch, the carb was pouring gas out of it and I never got it started again. I have yet to rebuild the carb because Ive been too busy with other projects and work, so, I may just drop it off and have it done at a power products shop to get it right the first time when I have a chance to do so. I had somebody offer me one of theirs, but, they never replied. I am still willing to pay them for the shipping, in fact I will do so if they bring it to UPS, however, UPS will require it to be emptied of fuel and probably oil as well, which is ok by me. I will replicate it anytime if somebody wishes to send one to me.. I have the cans still set up, ready to go!

I did find when I did this that my little heater claims to be 1500 watts output max. I see exactly 800 watts rms, as seen in my Pelex video. I am going to refilm all of my videos that really perform, and Pelex is my most prestigious device, and I have very easily self looped it once I added a cap to gain a resonant rise, but, it releases a strange pulse of emf per cycle that emits some sort of unknown wave that eliminates cellular all the way to my neighbors homes, and, it shuts down their wifi. I've tried to have a very famous college do a study on the device and they were not able to determine the type of energy emitting from the case even when grounded. Its not radioactive, not alpha or beta, nor gamma or xray, and it isn't rf since the device rings at 60 hz and has a fairly clean sinewave. My investor wants out now, so, I may sell his portion back to him, however, I haven't determined if the wave is dangerous or not, however, I am still here, but I havn't operate Pelex in months because I took it apart so if it were stolen, I wouldn't lose anything!

I have however been having a lot of luck with my Don Smith modules. I have started to make the table top device and have found that Don's was a demonstration hoax, so, I found that Don's coils could never have resonated anywhere near the frequencies he claimed unless the Bertonee NST fed the system with a much different output frequency. I used exactly the same L1 winding as Don, amp king 8 gauge wire, and the inductance was around 1.5 uh and the .2 uF capacitance would never resonate at 35.1 khz, no matter what the NST had for capacitance because it is isolated with a diode! it would resonate at more like 290.5 khz . Don's L2 winding was capped for resonance across only one of the coils, however, the coils were put in parallel later isolated by diodes, so, I am only stating the inductance would be for 1/2 of the coil, which would be 10.95 uH and the capacitor he used was a .47 uF cap. The resonant frequency for this combo is approximately 70,155 hz or70.15 khz... again, off drastically, but, enough to get my light bulb to light a little bit, so, something was going on and it wasn't to do with resonance. I found a lot of luck using the B&W coil with 60 turns @ 70 uH and it is 10" and 3" in diameter. I separated the coil into two pieces precisely and found that .3 uF is my resonant frequency for both the primary and secondary. I made a pancake coil for the primary and it outputs serious power, but, I never finished that.

The first .1 uf caps I used were similar to what he said, and before I found the company who literally made his capacitors for $50 each, I bought mine from ebay for $8 each and they burnt up at 4200v very easily since I wasn't monitoring the voltage. I have since found the real caps and if anybody wants to buy some., I will be selling them on Ebay very shortly for my cost. These capacitors have something magical about them.. it is the finest mica cap I have ver used, however, they are true self healing caps that are truly manufactured with serious precision and are of the finest quality. They are no longer Cornell Dubier, I have been working with them for a while since I've owned and operated Advanced Electronic for 6.5 years online, and only recently have shut the online store down when my Dad passed away since I just haven't had time to run it since I took over the family electrical construction business. So, I get the best of both worlds, quality electronic components from anybody I need in bulk, and electrical distribution and transmission products of any kind I ever need , that's why I have stated that I can acquire any transformer that anybody needs, from massive generating plant transformers to pole type and padmounts for URD systems.. we do it all!!

Best Regards,
Marc

[BroMikey]

Hi Marc

Dave emailed at XMAS and said that you or he had the address?
Something like that. I thought you had it already. Did you lose any
messages?


I see I need to
watch your new video's and catch up. Keep talking Marc, these
people are putting me to sleep.

I will comment soon on your new video's.

[BroMikey]

Self Looped Motor Generator Gerard inspired.


Overunity and self looping

[VIDEO]https://www.youtube.com/watch?v=vHYHeDN0078[/VIDEO]

[BroMikey]

Motor Generator

[VIDEO]https://www.youtube.com/watch?v=nAseG7z_GQo[/VIDEO]

[BroMikey]

Gerard Morin inspired direct drive motor generator
research and development. I wonder why Gerard
went underground? Maybe he got a shock and became
sick. Does anyone know what happened to Gerard?

I understand the dilemma Gerard was having with
running these motors 5000 rpm's. This poor guy
is just not receiving any support.

I hope nothing bad happened to Gerard. I guess
he has been pretty frustrated and has withdrawn
to develop new strategy.

I don't know? Either way Gerard put alot of goodies
on our plate to give a try.


[VIDEO]https://www.youtube.com/watch?v=7Edcl_L0lco[/VIDEO]

Published on Apr 23, 2016

Installed sensors on Mr Gerard's motor. Impressive motor with
fast RPM , not sure if it's because of the gage of wire used in
the rotor which seems to be thicker? None the less impressive
results. I'll keep plugging away to get the RPM up to Generator
requirements. Still can't get the idea of 36. 9 out of my head.
9 poles to spin a 36 pole motor for some reason. Could be
because I got the motor to turn off another's sensor?

[Belangers]

Hey BroMikey,
If I had the correct working generator, the McCulloch, I will easily replicate this. Hitby13kW has come really close to doing so, however, he missed 2 important steps which I have sent messages to him to tell him where he has gone wrong.

I have many transformers for sale and just received some yesterday that are the type necessary to function in Gerard's circuit, however, the generator must NOT have a breaker or a GFCI so it functions correctly, and, the generator used must have a fused output or the breaker must be bypassed for correct function and fuse be installed . The generator must be a permanent magnet electrical generation by means of either a permanent magnet rotor, or, a coil rotor and permanent magnet stator. The generator can't be a shunted generator or electromagnet core and coil stator because it causes a complete short when the input to the transformer is shorted out as needed, or it uses too much energy to be "over efficient" and will hinder the amplification needed which is caused by the capacitive draw the transformer creates from the Magnetosphere..

If the person replicating the circuit would listen to me, they need to follow my instruction. They need to watch Gerard's video very closely and follow these instructions I give here:

They need to short together the secondary circuit of the transformer, shorting together the left and middle secondary connections, then, they need to connect the generator's hot or black wire to this. The right side needs to connect to the neutral or common (white lead), and if you all notice, this will connect the outside of the can to the hot or + polarity , opposite of how the can is intended to operate, and, the can must not be grounded whatsoever!. The outside of the two cans must be bonded to each other, and, the can must be isolated from ground completely, as well, the generator must be isolated from ground, which Hitby's is NOT, it is laying on the concrete which is a decent ground. A rubber blanket or wood pallet needs to be under the generator.

This makes the outside of the transformer a + and the bushing will become the -. The bushing will attract the + dc energy from the magnetosphere and create a direct connection of an aerial plasma tube of Earth's atmosphere to the - bushing. When the generator pulses the energy in one direction, the bushing will attract the energy, when the pulse flops to the other side of the spectrum, the can will attract the energy, or eliminate the attraction, creating a massive burst of back emf and another energetic attraction to the circuit in the opposing manner. This will draw in more energy from the Atmosphere via plasma tube to the can's outer casing which will output any amount of energy needed to the circuit provided the electrical connections of the appliance are not grounded, or, if they are, the neutral must NOT be tied to it. The casings of appliances can only be grounded if the neutrals aren't tied to ground otherwise the energy will NOT flow. If the outside casings of the appliances are not grounded and the neutrals are tied to the case, since the energy is reversed on the transformer in one half cycle, the outside casing of the appliances may electrocute the user if touched with the back emf burst, so, special care must be considered for this type of application, and the user or operator must know this can and will happen, especially of the load is a high resistance load, the electricity will flow through them instead of the load if the body's resistance is lower than the load. In the opposite half of the cycle, since it is radiant energy, the opposite is true.. The radiant energy will flow with great force through high resistance connections, so, again, there is and will never be perfect protection unless the transformers are inside of a protective enclosure and the appliances are externally grounded while neutrals are disconnected from the casings at all times!!

The energy used is 100% radiant energy except for the prime mover's energy used to fire the circuit, which will be approximately 1 amp. Even this is the energy (the approximate 120 watts ) needed to fire the secondary coils of the transformer and the capacitance created in the can is only due to the change in polarity in the ac wave or dc pulsed waveform. This means the capacitive charge will change, on for charge and off for discharge, giving the output a ferromagnetic resonance that discharges into the load on every half cycle. This is how the arrangement works and if it isn't connected exactly as I just said, it will NOT work, or can kill the experimenter. Hitby13kW doesn't do this correctly in his videos, however, he may have changed this to try what I have suggested over time, but, I am willing to show this myself if somebody would donate the McCulloch generator.to me, or sell one to me rather cheap. I need them to contact me, and i know you have arranged somebody to give me one, but, they didn't have time to package it up and ship it to me. I will pay for the shipping if they wish to do so, howver, they need to get it to a shipping company and insure the generator has no fuel in it, and it gets to me in one piece. They may wish to build a wooden frame around it and I will replicate the circuit once I receive it, but, the circuit will NOT show digitally more in than out, but, analog meters will show this and the appliances being used will be powered correctly and function.

Here is what I can offer folks if they want to duplicate the circuit:
I just wanted to let you know that I have received a bunch of working but used utility transformers that we are selling. They are "pole" transformers, so, anybody interested could take advantage if they are in or near the CT area. The transformers were energized up until 2 days ago and work perfectly, however, buyers will have to take full responsibility for incidents/accidents, electrocutions, or spills/destruction during shipping if they buy them, waiver must be signed. The transformers cost $300 for the smallest (15kVA or 20) 25kVA are $450 each and 50kVA for $600 each. They easily cost double for refurbished units and the customer is responsible for the shipping/securing of the transformers and of course insurance of the shipment. We will load them for the buyer or shipper and will give a phone number to you if you know any interested folks. That is a great deal and I will video myself testing the coils with a meggar if they are interested in buying them. They fed an old establishment which was a GE factory that was recently demolished. We acquired them by giving them a credit for each one off of our final construction cost. Anyway, I am willing to work on the price for anybody interested in buying the entire lot and the offer prices or agreed price will need to be for cash if they want them all of in a bulk purchase. Other than that, company checks or personal checks will be accepted after they clear into our account. Please let me know if anybody is interested in buying them, they will work for the Gerard Morin setup if they listen to how I set them up. The generator used must not have a gfci or breaker, they will only work if the generator used is a permanent magnet genrator with a fused output. The breakers in a generator or gfci will open, eliminating function because a standard style generator coil is being shorted out due to the fact that shorting the coil as Gerard did creates an unwanted shunt across the generator coil causing a trip.

Please have interested buyers contact me privately and I will arrange to meet them at my shop and ship these units, however, we will not be responsible for damages, injuries, oil spills, broken equipment or burned out appliances, or even worse, fires because of their negligence or lack of experience/expertise. These transformers are no joke and they are not toys, they are and can be lethal if used with an input of any significant amperage, meaning that 1 amp at 120v can kill somebody, especially if they connect the transformer's secondary to a wall outlet, the amperage on the high voltage side is instantaneously lethal; and will blow off limbs, etc.

amplification of this energy can kill even easier and is not recommended that anybody other than a seasoned high voltage expert should be playing with these devices. They have no business doing so, not even master electricians should do so as they are not experts with high voltage utility systems and are usually not trained for the safety of high voltage systems.

[BroMikey]

Hey BroMikey,
If I had the correct working generator, the McCulloch, I will easily replicate this. Hitby13kW has come really close to doing so, however, he missed 2 important steps which I have sent messages to him to tell him where he has gone wrong.

I have many transformers for sale and just received some yesterday that are the type necessary to function in Gerard's circuit, however, the generator must NOT have a breaker or a GFCI so it functions correctly, and, the generator used must have a fused output or the breaker must be bypassed for correct function and fuse be installed . The generator must be a permanent magnet electrical generation by means of either a permanent magnet rotor, or, a coil rotor and permanent magnet stator. The generator can't be a shunted generator or electromagnet core and coil stator because it causes a complete short when the input to the transformer is shorted out as needed, or it uses too much energy to be "over efficient" and will hinder the amplification needed which is caused by the capacitive draw the transformer creates from the Magnetosphere..

If the person replicating the circuit would listen to me, they need to follow my instruction. They need to watch Gerard's video very closely and follow these instructions I give here:

They need to short together the secondary circuit of the transformer, shorting together the left and middle secondary connections, then, they need to connect the generator's hot or black wire to this. The right side needs to connect to the neutral or common (white lead), and if you all notice, this will connect the outside of the can to the hot or + polarity , opposite of how the can is intended to operate, and, the can must not be grounded whatsoever!. The outside of the two cans must be bonded to each other, and, the can must be isolated from ground completely, as well, the generator must be isolated from ground, which Hitby's is NOT, it is laying on the concrete which is a decent ground. A rubber blanket or wood pallet needs to be under the generator.

This makes the outside of the transformer a + and the bushing will become the -. The bushing will attract the + dc energy from the magnetosphere and create a direct connection of an aerial plasma tube of Earth's atmosphere to the - bushing. When the generator pulses the energy in one direction, the bushing will attract the energy, when the pulse flops to the other side of the spectrum, the can will attract the energy, or eliminate the attraction, creating a massive burst of back emf and another energetic attraction to the circuit in the opposing manner. This will draw in more energy from the Atmosphere via plasma tube to the can's outer casing which will output any amount of energy needed to the circuit provided the electrical connections of the appliance are not grounded, or, if they are, the neutral must NOT be tied to it. The casings of appliances can only be grounded if the neutrals aren't tied to ground otherwise the energy will NOT flow. If the outside casings of the appliances are not grounded and the neutrals are tied to the case, since the energy is reversed on the transformer in one half cycle, the outside casing of the appliances may electrocute the user if touched with the back emf burst, so, special care must be considered for this type of application, and the user or operator must know this can and will happen, especially of the load is a high resistance load, the electricity will flow through them instead of the load if the body's resistance is lower than the load. In the opposite half of the cycle, since it is radiant energy, the opposite is true.. The radiant energy will flow with great force through high resistance connections, so, again, there is and will never be perfect protection unless the transformers are inside of a protective enclosure and the appliances are externally grounded while neutrals are disconnected from the casings at all times!!

The energy used is 100% radiant energy except for the prime mover's energy used to fire the circuit, which will be approximately 1 amp. Even this is the energy (the approximate 120 watts ) needed to fire the secondary coils of the transformer and the capacitance created in the can is only due to the change in polarity in the ac wave or dc pulsed waveform. This means the capacitive charge will change, on for charge and off for discharge, giving the output a ferromagnetic resonance that discharges into the load on every half cycle. This is how the arrangement works and if it isn't connected exactly as I just said, it will NOT work, or can kill the experimenter. Hitby13kW doesn't do this correctly in his videos, however, he may have changed this to try what I have suggested over time, but, I am willing to show this myself if somebody would donate the McCulloch generator.to me, or sell one to me rather cheap. I need them to contact me, and i know you have arranged somebody to give me one, but, they didn't have time to package it up and ship it to me. I will pay for the shipping if they wish to do so, howver, they need to get it to a shipping company and insure the generator has no fuel in it, and it gets to me in one piece. They may wish to build a wooden frame around it and I will replicate the circuit once I receive it, but, the circuit will NOT show digitally more in than out, but, analog meters will show this and the appliances being used will be powered correctly and function.

Here is what I can offer folks if they want to duplicate the circuit:
I just wanted to let you know that I have received a bunch of working but used utility transformers that we are selling. They are "pole" transformers, so, anybody interested could take advantage if they are in or near the CT area. The transformers were energized up until 2 days ago and work perfectly, however, buyers will have to take full responsibility for incidents/accidents, electrocutions, or spills/destruction during shipping if they buy them, waiver must be signed. The transformers cost $300 for the smallest (15kVA or 20) 25kVA are $450 each and 50kVA for $600 each. They easily cost double for refurbished units and the customer is responsible for the shipping/securing of the transformers and of course insurance of the shipment. We will load them for the buyer or shipper and will give a phone number to you if you know any interested folks. That is a great deal and I will video myself testing the coils with a meggar if they are interested in buying them. They fed an old establishment which was a GE factory that was recently demolished. We acquired them by giving them a credit for each one off of our final construction cost. Anyway, I am willing to work on the price for anybody interested in buying the entire lot and the offer prices or agreed price will need to be for cash if they want them all of in a bulk purchase. Other than that, company checks or personal checks will be accepted after they clear into our account. Please let me know if anybody is interested in buying them, they will work for the Gerard Morin setup if they listen to how I set them up. The generator used must not have a gfci or breaker, they will only work if the generator used is a permanent magnet genrator with a fused output. The breakers in a generator or gfci will open, eliminating function because a standard style generator coil is being shorted out due to the fact that shorting the coil as Gerard did creates an unwanted shunt across the generator coil causing a trip.

Please have interested buyers contact me privately and I will arrange to meet them at my shop and ship these units, however, we will not be responsible for damages, injuries, oil spills, broken equipment or burned out appliances, or even worse, fires because of their negligence or lack of experience/expertise. These transformers are no joke and they are not toys, they are and can be lethal if used with an input of any significant amperage, meaning that 1 amp at 120v can kill somebody, especially if they connect the transformer's secondary to a wall outlet, the amperage on the high voltage side is instantaneously lethal; and will blow off limbs, etc.

amplification of this energy can kill even easier and is not recommended that anybody other than a seasoned high voltage expert should be playing with these devices. They have no business doing so, not even master electricians should do so as they are not experts with high voltage utility systems and are usually not trained for the safety of high voltage systems.

I am on the run, it is AC cooling weather here in Kansas, I will answer you
later today also will see if I can bring up this subject again with David. He had a few that he pieced together from what I remember and maybe
he didn't want to send you a dud.

I will find you another Genset and we will see. Thank you for inspiring
me, keeping this thought alive. I know it will work as we loose all
resistance to flows to huge amounts of energy.

I remember what you said about having Xformers on pallets
in metal building and so on. What a subject, it is becoming
much more of a reality with each passing day as I stay
focused on this new energy vane VS the old school thinking.

[BroMikey]

This stuff is important to me, Dave said he sent you information
months ago, I told you and you did not respond. No need to
say anything about the lose of emails and time, I can hardly find
my head with both hands somedays when I get busy.

This is part one of many posts that will follow just browse
and we will consider the possibilities. One thing I can do is
locate parts. This one is to far away.

http://www.kijiji.ca/v-home-outdoor-other/
kamloops/mcculloch-generator/1104097107

[BroMikey]

Ottawa is near New York state Probably to far she smokes.

It is a 3300 watt. Shipping is high.


http://www.kijiji.ca/v-tool-other/ottawa/3300watt-mcculloch
-portable-older-generator/1160842702?enableSearchNavigation
Flag=true

[BroMikey]

These links may or may not work however we can get an
idea what's out here. No rush.

http://www.auctionsinternational.com/auction/7058/item/mcculloch-mite-e-lite-generator-42822

[BroMikey]

This person is in Maryland posted in 2010

Sold for $40? I guess so.



https://www.govdeals.com/index.cfm?fa=Main.Item&itemid=306&acctid=1158

[BroMikey]

June 18th is the day of an ESTATE AUCTION in Illinois with
one item being a MITE E LITE Mcculloch GENSET

Call Jordan Auction Service 217-827-2599 to see what kind of shape the unit is in
and to see if he is willing to ship out the unit to other states. Call Jordan.



http://www.auctionzip.com/cgi-bin/auctionview.cgi?lid=2702362