Announcement

Collapse
No announcement yet.

Mikey's Beast SSSG OSCILLATOR

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Hi folks, Hi mike, so which circuit or setup are you recommending people try.
    I notice in the part 22 small clip, he shows the north pole motor, with a more elaborate circuitry.
    peace love light

    Comment


    • Originally posted by SkyWatcher View Post
      Hi folks, Hi mike, so which circuit or setup are you recommending people try.
      I notice in the part 22 small clip, he shows the north pole motor, with a more elaborate circuitry.
      peace love light
      Hi Sky
      Thanks for sharing all of your experiments. I want to say that people
      who show real results will succeed like we see with you. The answer to
      your question is a "HIGHLY MODIFIED BEDINI-COLE CIRCUIT"
      Well this was the answer that JOHN gave after he set the stage for
      why we were only given table scraps.

      The LOW DOWN? OH goodie, I thought no one would even ask. It is
      not complicated enough so no one cares I guess. I am sorry Sky
      I don't mean to rant so much, it's just that I expected more out of
      people than I am seeing.

      The circuit? The circuit is one answer and in this video John says
      that the circuit throws out 2 spikes AND THEN the gated magnet
      flips polarity.

      You see I am in the generation born in the mid to late 50's so I see
      things from two sides. One side Grandpa worked with and dreamed
      about vacuum tubes and the other side is super chips fully programmable.

      John Bedini's rock collection/grinding and binding always run through
      my mind since I watched the rise of the semiconductor industry, wishing
      someday I could squeeze my own crystals.

      The answer is in the circuit but I think the rest of the answer is not so
      common of a subject so we need to address that first.

      Take a ceramic magnet disk,a rubber magnet disk, a thin neo magnet disk
      and stack them up. Put an LED indicator for North and South pole
      measurements on each side say 4 inches away.

      Again stack your magnets and begin to change the distance between
      the individual sections while your 2 measuring devices are placed on
      each end of your experimental setup.

      As you adjust the distances between rubber, neo and ceramic the polarity
      may or may not flip at different placements. Shielding by using thin strips
      set on each side or back may change magnetic field reactions.

      The trick is to set up a field using magnets that becomes very touchy
      if we can put it that way. Fields on the verge of flipping polarity but
      not, until a spike is introduced. At that point the tiny amount used
      in electrical energy might be recovered when the polarity flips and
      magnetic energy is sent back into the coil.

      Then another spike is sent to flip the polarity back to it's original state
      waiting for the next event to occur. Well this is my educated guess.

      So the answer is in the magnetic gating action that gives an extra
      amount when the flipping occurs and wow. Think about how strong
      magnets can be and when they are set up to cancel out the forces
      they offer in a static condition. Think about just how much power
      they can offer our empty coils.

      Static fields offering 50 lbs normally yet cancelled and on the brink
      of flipping polarity using a tiny input to do it.

      The magnet motor I am doing now is teaching me this principle.
      Last edited by BroMikey; 11-25-2015, 01:14 AM.

      Comment


      • Originally posted by scratchrobot View Post
        Yes you are right, it can't get any simpler and it's better to let your hands do some work instead of hanging out on this forum all day.
        Maybe you can make a video yourself with your free energy device when you are done?

        Good luck and let us play with the ones and zeros.
        Hey Scratch
        Don't get me wrong I play with the zero's and one's, but what I am saying
        is that digital networks don't spell out O.U. just because. And there is always
        some time in the day to give you my thoughts.

        I guess you are not interested in the Bedini stuff or you would know
        that I already gave you the answer you need to perfect the monopole.

        If you ever built a Bedini device at all. Just Zero's and One's are not enough.

        Comment


        • Hi mike, thanks for sharing what you have found out about bedinis work.
          So based on your description, here is the image that formed in my mind.
          A coil, with two same polarity permanent magnets on either side and each has this differing type magnets stacked to cause a shift in magnetic strength from either end of coil, due to a pulse from coil.
          Sure seems somewhat similar to what magnacoaster is doing from my comprehension of his work.
          If polarity of either magnet is really changing, i'm having trouble visualizing how that is happening.
          peace love light

          Comment


          • Originally posted by SkyWatcher View Post
            Hi mike, thanks for sharing what you have found out about bedinis work.
            So based on your description, here is the image that formed in my mind.
            A coil, with two same polarity permanent magnets on either side and each has this differing type magnets stacked to cause a shift in magnetic strength from either end of coil, due to a pulse from coil.
            Sure seems somewhat similar to what magnacoaster is doing from my comprehension of his work.
            If polarity of either magnet is really changing, i'm having trouble visualizing how that is happening.
            peace love light

            It is hard to explain so here is the basic concept. John pointed out that
            the rotor magnets on the big Ferris wheel were not just regular or
            standard ferrite and that behind the visible ferrite was in fact a rubber
            magnet and behind that a Neo magnet.

            I have no clue if my drawing is correct and is only a conceptual entry to
            stimulate our desire to go deeper. John asked "Did anyone remember the
            Howard Johnson video's that he had done? Reminding us that Howard
            designed magnetic gates that switch polarity and that in fact his rotor
            magnets were an off shoot of that work.

            That the SG group never got the full details though John had originally
            intended for them to build units such as he has. Not the table scrap
            version the rest of us have that are a 1.1 cop to 1.3 cop.

            Just plain and simple magnetic fields being used to harvest joules. Not
            ice creeping in the windows because vacuum energy was present..
            Everyone wants the hair standing on the back of their necks as they
            see the OU creeping like Kudzu up the house wiring, some silly
            supernatural lie.

            But who want to do the foot work?

            Table scraps will work as a great battery tech to keep the plates clean
            and therefore fully charged without damage. The monopole groups, the
            yahoo's on them insulted John constantly so they never got the full
            details.

            In the diagram the magnets do not actually flip all of their pole as shown
            instead the entire gate flips pole, it is up to us to build a gate to operate
            in a reversible action. Kick it once and the gate flips to south, kick it again
            and the gate(series of magnets shown) flips back to north.

            Earlier I made a suggestion that maybe the experimenter might build his
            or her gate while a measuring tool lie at each end, to detect changes in
            the field.

            This is how I see the idea.


            Last edited by BroMikey; 11-25-2015, 08:35 AM.

            Comment


            • Another very important innovation that John talked about was
              his pie shaped magnet experiment on the cole motor in the center
              of the Ferris wheel that is used as a highly efficient generator to
              keep the system tronix running along.

              You will note the distances A, B, C that A (section of the magnet)
              travels further than the C (section of the magnet) thereby balancing
              up the loading on the coils to reduce resistance.

              Thanks -A - Million John



              Comment


              • This is yet another way to charge a battery using an oscillator.
                I am realizing the benefits of the fast recovery diodes more
                than ever. Anyone who has a high frequency oscillator such
                as an SSSG is not doing their circuit justice by using a 50 cent
                general purpose diode.

                When i use to use a standard general purpose diode on the output
                of my SSSG charger/Energizer the 6a part would begin to get hot
                hot at a few hundred milliamps due to the nature of HF oscillations.

                When I finally broke down and spent a full dollar for a fast diode
                the energy harvested nearly doubled and not only did the heat
                issue at the rectifier vanish but so did the burning heat in the
                oscillator section.

                It finally did self destruct using the general purpose diodes
                at only 800 milliamps per strand. With the fast diodes I can
                run 5 amps if I want and the circuit is not bottle necked
                with all of the reflect energy trashing my oscillator.

                It seems that once you hit the critical milliamp ceiling these 60hz
                general purpose diodes act as resistors and the more power fed
                into the circuit just goes out as heat with little to no increase in
                output power for 4X input.

                Using General purpose diodes for an oscillator is an insult to intelligent
                design. Beginners are instructed to use these type of diodes in almost
                every basic circuit shown on the web.

                This circuit as shown is the best you will find that can charge a
                battery at 100 percent efficiency, thanks to John Bedini.



                These are just fast diodes not the ultra fast but they are the
                biggest fast high amp handling for the lowest price.

                10pcs 40EPF12 Encapsulation to 247 Fast Soft Recovery Rectifier Diode | eBay


                Also the transistor for higher voltage oscillations.






                10pcs MJL4281A Audio Power Amplifier Transistor A124 | eBay


                Last edited by BroMikey; 02-08-2016, 08:01 AM.

                Comment


                • Understanding Oscillation performance

                  BroMikey

                  What would be the greatest factor in controlling the circuits ability to oscillate? I have built a charger similar to your layout but as yet I haven't got it to oscillate. My coil is 5 strands of litzed 24awg with a single line of 32awg for trigger. Runs are at 60ft. May be not long enough.

                  From what I have read there is some suggestion that changing the values of resistors can effect oscillation and you indicate power level input alters it as well? And I am sure that the coil build has to be within certain parameters that are known to work.

                  I am going to build your latest design but I would like to get this first charging circuit of mine to function correctly before I advance to another level.

                  By the way, what do you think a ballpark figure for parts for your circuit would be?

                  I appreciate your sharing. Finding definitive answers on radiant chargers can be a daunting task on the internet. I can resonate with old school logic. Simple, robust, can tolerate extremes..... my kind of approach.

                  My main goal right now is desulfating deep cell batteries. Once I get the desulfator operational I will construct the Gen Mode and then the safety voltage circuit. I want to keep it basic and expand from there.

                  Comment


                  • Hello Why-Me

                    Here is 1 diagram for gen-mode on my units. You will
                    notice the standard SG circuit to the right hand side
                    and the left side the control circuit for over voltage.

                    Note the Genmode switch and the 6A10 diode just above it
                    that I now have replaced with a more powerful diode number.

                    I had to really dig to find my old thread.

                    Last edited by BroMikey; 05-01-2016, 03:44 AM.

                    Comment


                    • Originally posted by pipster55 View Post
                      BroMikey

                      What would be the greatest factor in controlling the circuits ability to oscillate? I have built a charger similar to your layout but as yet I haven't got it to oscillate. My coil is 5 strands of litzed 24awg with a single line of 32awg for trigger. Runs are at 60ft. May be not long enough.

                      From what I have read there is some suggestion that changing the values of resistors can effect oscillation and you indicate power level input alters it as well? And I am sure that the coil build has to be within certain parameters that are known to work.

                      I am going to build your latest design but I would like to get this first charging circuit of mine to function correctly before I advance to another level.

                      By the way, what do you think a ballpark figure for parts for your circuit would be?

                      I appreciate your sharing. Finding definitive answers on radiant chargers can be a daunting task on the internet. I can resonate with old school logic. Simple, robust, can tolerate extremes..... my kind of approach.

                      My main goal right now is desulfating deep cell batteries. Once I get the desulfator operational I will construct the Gen Mode and then the safety voltage circuit. I want to keep it basic and expand from there.

                      Sorry about missing your post for a while. Glad you have some
                      questions such as frequency of oscillation. A tank circuit is
                      formed by a single resistor because the coils have capacitance.

                      My large 14 awg uses only resistors. The very fine wire works
                      well for very small power outputs and when you turn down
                      the output to the charge battery oscillation may sometimes
                      stop and start again.

                      If this occurs you will not get your battery charged properly.
                      For very fine wire I use more capacitance than just the coil
                      has to offer, across the resistor on the base.

                      The price for parts will be a few hundred.

                      The length of wire for an 18awg wire should be around 150 feet
                      while the length on a 20 awg wire will be 130 feet and a 22 awg
                      might be 100 feet, a 22 awg 80 feet, just generally. 24awg is
                      about 60 feet, you are correct.

                      My 14 awg coil should be 180 feet but I wound it at 130 feet
                      and it works okay.

                      Comment

                      Working...
                      X