Barbosa and Leal Devices - Info and Replication Details

[wantomake]

Lively is good

Thanks Clarence,
I am working all day, but tonight will get into the shop and remove one of the toroids and test the setup. How long is your captor loop #1 cable? My present one is only 2 - 3 feet long. Will check to be sure.

I still only have a few rods in the ground but want to try any way.

Luc,
Hope you success on your setup. I plan to add to my ground grid as monies allow. I have 2k watt inverter, bank of solar batteries, and small ground grid. I also do other ground energy harvesting experiments with my ground grid. Will post any positive results as I experiment.

Look forward to more fun,
wantomake

[luc2010]

Yes, IO5 AMPS from batt+Inverter

Hello Clarence,Wantomake and ALL

Hello wantomake,

I can't speak for Luc - but I,m pretty sure it's just inverter as I recently advised him to stop using any mains power at all. the photo is the recent one I put together to show how to do it and kill the lenz effect while doing it
because THAT is what ALL of the B&L units do in order to be effective at all.
as long as the LENZ effect is alive and operating as todays so called electrical engineers say that it will be no B&L unit will get anywhere.

Yes, i am using the Inverter to power the unit, Only!! No mains

hope soon can i finish the setup exactly following the instructions, and see whats the results!!

soon!

Thanks and Regards
luc2010

[clarence]

Luc2010,
That's high amps off of one toroid!! Are you using an inverter or mains power? I look forward to your results.

Clarence,
Nice one toroid build. I haven't tried that yet. The captor looks much longer so will give that setup a try on Tuesday.

Thanks for all,
wantomake

Hello wantomake,

I can't speak for Luc - but I,m pretty sure it's just inverter as I recently advised him to stop using any mains power at all. the photo is the recent one I put together to show how to do it and kill the lenz effect while doing it
because THAT is what ALL of the B&L units do in order to be effective at all.
as long as the LENZ effect is alive and operating as todays so called electrical engineers say that it will be----- no B&L unit will get anywhere.



in the photo note the direction of the #1 awg wire winds and how the direction of the bottom of the 5 turns passes one time thru the toroid
and then connects back to itself by a split-bolt connector.
I did not finish out the rest of the build (which was B&L's #2 generator-my gen unit is their #1 type) as I have way lots more going on at present than anyone can imagine.
however, need any info, just post and I will get to it. I check in and out often everyday! keeps the blood flowing so to speak.

lovin-it!
Respectfully ,

Clarence

[wantomake]

105 amps!!

Luc2010,
That's high amps off of one toroid!! Are you using an inverter or mains power? I look forward to your results.

Clarence,
Nice one toroid build. I haven't tried that yet. The captor looks much longer so will give that setup a try on Tuesday.

Thanks for all,
wantomake

[clarence]

Hello Clarence and All,

Nice Photos!!

I power the unit and the current on the closed loop went to 105 AMPS!!
(it should be 109 AMPS)

working on it!

Later

Thanks & Regards
luc2010

hELLO lUC2010,


hold on!!!!!! DON'T DO ANYTHING!!!!!
THE IO5 AMPS IS PERFECT!!!!
NOT ALL TOROIDS AND LENGTHS OF WIRE WILL GIVE THE SAME RESULTS!

lEAVE everything JUST as it is and start hooking some light loads to the CAPTOR circuit and see what results come up.
the CAPTOR circuit will be in the diagram I previously sent you by E.
I have re included it here:


follow the diagram and you should finally see results.

Clarence

[luc2010]

Thank you so much!!

Hello Clarence and All,

Nice Photos!!

I power the unit and the current on the closed loop went to 105 AMPS!!
(it should be 109 AMPS)

working on it!

Later

Thanks & Regards
luc2010

[clarence]

Hello Mr Clarence,

Thank You Very much on this INFORMATION FOR CONSTRUCTION OF SINGLE TOROID with SINGLE CAPTOR COIL!! SIR, i am sure many members will appriciate it!
Best Regards
luc2010

Hello Luc2010,

Here is what you were asking about.




enjoy.

Clarence

[clarence]

[QUOTE=BroMikey;288535]
Good Man Clarence keeping your ducks in a row.

Been waiting on you, like one experimenter waits on another.

I can't get over this beautiful transformer experiment
(Not a battery) wow so much to learn. I saw your other
post also. I can't wait to hear more about how you have
a dipole generator that other forms of energy can be
siphoned off without increasing the input.

A wonderful adventure in oscillator design.

All of your experiments from the past will payoff.

It is going to be a super finding.



[/QUOTE)


Hello BroMikey,

Have been working overtime for certain on what was supposed to be a
simple IC555 /2N3055 oscillator circuit but so far the transistor end for some reason has been eating my lunch. will sooner or later find the problem
and get things finished. (sooner I hope).

May have to just go back to a mother board and build a separate LED BLINKY
circuit to establish where and what the problem IS. this way I won't have to tear down my already built oscillator "BOX" build - just find the problem and fix it!

Good to hear from you as ALWAYS!

Respectfully,

Clarence

[BroMikey]

Glinski -

when you made your first posts I didn't make much about it. However
this is NOT a battery thread - It is NOT a energy from the ground thread -
It IS a DEDICATED THREAD for one type of DEVICE which is the BARBOSA & LEAL DEVICE and information pertaining to IT and its improvements!!!!!!

other thread members have rose up in the past to keep this thread TOTALLY in line with what LEVEL the thread administrator created it FOR!

It is evident that such an attribute DOES NOT prevail within you!!!!!!!!!

the important word here is GO ! GET IT DONE!


Clarence

Good Man Clarence keeping your ducks in a row.

Been waiting on you, like one experimenter waits on another.

I can't get over this beautiful transformer experiment
(Not a battery) wow so much to learn. I saw your other
post also. I can't wait to hear more about how you have
a dipole generator that other forms of energy can be
siphoned off without increasing the input.

A wonderful adventure in oscillator design.

All of your experiments from the past will payoff.

It is going to be a super finding.

[clarence]

Hi bromikey you right on the batterys being in parallel. But internally they are in series.when the hi positive hits the battery positive it regauges the battery and pulls electrons from the environment Thu the cells from the ground . ionic cold charging . those battery's are like chemical capacitors. Internally. In series. Those battery are so jamed with positive hi voltage that a neon lights on the case.one huge attraction for electrons. Give it a ground and it's like a pipeline for electrons. Sorry about the confusion a slack hand creates wount. Jim out 🍺

Glinski -

when you made your first posts I didn't make much about it. However
this is NOT a battery thread - It is NOT a energy from the ground thread -
It IS a DEDICATED THREAD for one type of DEVICE which is the BARBOSA & LEAL DEVICE and information pertaining to IT and its improvements!!!!!!

other thread members have rose up in the past to keep this thread TOTALLY in line with what LEVEL the thread administrator created it FOR!

It is evident that such an attribute DOES NOT prevail within you!!!!!!!!!
So NOW I am telling you to go find a battery thread - a totally separate energy from the ground thread whatever that direction the thread was made for, or just create your own "whatever" thread!
the important word here is GO ! GET IT DONE!


Clarence

[jim glinski]

Hi bromikey you right on the batterys being in parallel. But internally they are in series.when the hi positive hits the battery positive it regauges the battery and pulls electrons from the environment Thu the cells from the ground . ionic cold charging . those battery's are like chemical capacitors. Internally. In series. Those battery are so jamed with positive hi voltage that a neon lights on the case.one huge attraction for electrons. Give it a ground and it's like a pipeline for electrons. Sorry about the confusion a slack hand creates wount. Jim out 🍺

[clarence]

Hello mr clarece, we are crossing finger then you find the way.

Hello fer,

HA! HA! I like that one!
I've been crossing my eyes , my legs, my arms , my trails, and my T's
just trying to get through finishing my Oscillator so that I can try it out
and see how well it performs (or not) so that I can in the end finish my Intermediate Frequency Transformer and make some headway.

am ready now to charge up a little 7 AH batt to give it a test run. will see
what happens!

Later! regards,

Clarence

[fer123]

Hello mr clarece, we are crossing finger then you find the way.

[BroMikey]

Hello BroMikey,

Haven't posted in a while as I have been busy finishing the IFT to be able to use all of the high frequency power that I have so easily made with Tesla coils to date. I was back to the 33.1 KHZ.
I turned the DVM BACK on (no damage thank goodness) and switched to
to acv mode. the voltage showed the 122 vac and I decided to turn the
trimmer switch and watch the voltage this time. when I moved the screw
about a half turn the the voltage rose to around 270 vac. I turned more
until the voltage hit 1000 vac and the DVM blinked out again. I turned the
screw back to zero and stopped that Bull S***. lesson learned!
3. DISAPPOINTING - the end results were disappointing in several ways.
I could not change the frequency with out changing the voltage (I never
have liked the IDIOT arcs and sparks scenario). Also I found that changing
the frequency at this end ALSO changed it at the ZVS end.

All in all this ultimately showed me that I have a very powerful transformer that I have built - that coil building is second nature to me now- AND that I have to have a totally separate sourced oscillator input at a set frequency.

I have spent about two weeks of days and nights in R & D to come up with the oscillator that I need ( I don't sleep and use the zombie method the rest
of the world does - time wasted!) .

Years back on DS I previously built a good OSC and that is the unit I am rebuilding with a few up dates and simplification (KISS in action- AKA- Keep It Simple Stupid).

will take a week or so to finish and then do some run time. It is what it is!

Thanks for listening BRO!

Clarence

Hey Clarence

That is one hell of an entry, I find your work very rich and
rewarding. I have seen may times how powerfully effective
a single variable cap is, such as in all radio work.

The other thing is the new IFT shielding has some good potential
for your future experiments. It might be that one wire moved
will make the new IFT do anything that you are looking for also.

I mean to tell you that I am WOW-ed by the fact that the whole
process can be squelched at the output end using a single Transformer.

I know how it is when you get going and run the red line into
exhaustion in your excitement. This progress is good stuff.

I'll be giving this more thought and let you know what I come
up with but as you know nothing takes the place of raw testing.

Keep me posted on the good stuff.

PS: I can;t help but wonder if you were driving a single device
what might be the reading as you adjust your varia-cap.

[clarence]

.

Hello BroMikey,

Haven't posted in a while as I have been busy finishing the IFT to be able to use all of the high frequency power that I have so easily made with Tesla coils to date. I had tried to use the small TBC pickup coil with it's 20 vac supply as an oscillator input to the IFT and that effort proved SUCCESSFUL - SURPRISING - DISAPPOINTING.

!.SUCCESSFUL - the two coils I made for the oscillator worked SPOT ON!
they took the 20 volts from the pickup coil and through the OSC side of the
new transformer and stepped it up to the 122 vac I wanted. all at 32.1
KHZ.
2.SURPRISING - to drop the frequency down slightly I paralleled a variable
trimmer capacitor across the second coil with its 122 vac. when I started
turning the small adj screw on the cap I watched the freq with my DVM
to be able to know when to stop. I didn't have any output wires placed into
the quick disconnect solder holes yet so I just placed my DVM lead probes
into them to monitor progress. after turning the screw and the freq
dropped from 33.1 to 38.9 I started to reverse the small screw turns
because two things happened. The DVM shut itself off because of it's
built in safety feature, AND there were DARK BLUE ARCS jumping around
on the ends of the probe tips. I was back to the 33.1 KHZ.
I turned the DVM BACK on (no damage thank goodness) and switched to
to acv mode. the voltage showed the 122 vac and I decided to turn the
trimmer switch and watch the voltage this time. when I moved the screw
about a half turn the the voltage rose to around 270 vac. I turned more
until the voltage hit 1000 vac and the DVM blinked out again. I turned the
screw back to zero and stopped that Bull S***. lesson learned!
3. DISAPPOINTING - the end results were disappointing in several ways.
I could not change the frequency with out changing the voltage (I never
have liked the IDIOT arcs and sparks scenario). Also I found that changing
the frequency at this end ALSO changed it at the ZVS end.

All in all this ultimately showed me that I have a very powerful transformer that I have built - that coil building is second nature to me now- AND that I have to have a totally separate sourced oscillator input at a set frequency.

I have spent about two weeks of days and nights in R & D to come up with the oscillator that I need ( I don't sleep and use the zombie method the rest
of the world does - time wasted!) .

Years back on DS I previously built a good OSC and that is the unit I am rebuilding with a few up dates and simplification (KISS in action- AKA- Keep It Simple Stupid).

will take a week or so to finish and then do some run time. It is what it is!

Thanks for listening BRO!

Clarence