Barbosa and Leal Devices - Info and Replication Details

[BroMikey]

Clarence,

Main want is as stated- please measure currents- incoming I1 and outgoing I2 as on drawing and announce them. It's easy with clamp meter.

Hi tvka

I have looked at this question and looked at this question and

looked at this question and finally I realized WHAT the question

is. The question IS

what is the current on L1 and L2

The way you typed the question is very confusing.

L1 = neutral and the designation L2 = hot leg

Before when you posted the question it looked like you wrote

"check 11 &12 for me" check current? 11 &12?


No!!!

Now Clarence is very busy and you guys need to follow this thread

like it is posted. Clarence just told you all that he does not

waste a lot of time with those measurements. If you want to

measure, that is fine.


In the future use the capital L1 and the capital L2 please.

It has taken me 2 days to understand you and I am sure

Clarence is on a new project that takes all of his time.

Clarence,


Could you please measure I1 and I2 and announce them?

[tvka]

BroMikey,

Why you say "great", when it's useless?

Clarence,

Of course, kWm readings will increase with load connected.
And that's about all what can be deduced. It's series circuit!
To see if we get additional current source due to captor existence, currents MUST be measured before and after captor.
Don't you really have a multimeter?

I'm just wandering where electromotive force for electron pumping comes from. Few turns around toroids secondary wire in fact makes a small, perhaps in order of 100pF capacitor- extremely loose coupling for 50/60Hz.

Current transformer could do, yet then it should be toroid around secondary wire...
However then sufficient secondary current is mandatory.

Regards

[tvka]

BroMikey,

Well, I meant capital I for current... as it's beeing used all over the world as far I know... indexes to see one from another... with AC ampmeter exactly in circuit sections as on drawing and with some load connected.

I'm kind of physicist and was teached that the main purpose of physicist is to measure

Regards

[BroMikey]

Clarence,

Main want is as stated- please measure currents- incoming I1 and outgoing I2 as on drawing and announce them. It's easy with clamp meter.

Hi tvka

I have looked at this question and looked at this question and

looked at this question and finally I realized WHAT the question

is. The question IS

what is the current on L1 and L2

The way you typed the question is very confusing.

L1 = neutral and the designation L2 = hot leg

Before when you posted the question it looked like you wrote

"check 11 &12 for me" check current? 11 &12?


No!!!

Now Clarence is very busy and you guys need to follow this thread

like it is posted. Clarence just told you all that he does not

waste a lot of time with those measurements. If you want to

measure, that is fine.


In the future use the capital L1 and the capital L2 please.

It has taken me 2 days to understand you and I am sure

Clarence is on a new project that takes all of his time.

Clarence,


Could you please measure I1 and I2 and announce them?

BroMikey,

Why you say "great", when it's useless?

Clarence,


Don't you really have a multimeter?

@TVKA

You are now hearing me. Your english is so bad you will

never follow directions.

This guy is a hard head also Clarence.

@TVKA

where is your reading? Go take readings.

[tvka]

BroMikey,

Oh, great
My english is far from perfect. Yet I can communicate in 4 languages.
Don't worry, I will have my readings. Just not with this silly "captor" setup.
Pretty evident it can not "pump" anything from earth.

Clarence on a new project? This one supposed to be finalized already?
Well, well

[BroMikey]

BroMikey,

Oh, great
My english is far from perfect. Yet I can communicate in 4 languages.
Don't worry, I will have my readings. Just not with this silly "captor" setup.
Pretty evident it can not "pump" anything from earth.

Clarence on a new project? This one supposed to be finalized already?
Well, well

Are you calling Clarence Captor replication silly?

Bad boy, not good. How do you say "Hard Head in 3 other

languages? Clarence is not going to let you call his captor a lie.

Go take readings and come back when you are serious.

No one has asked for your endless wisdom of consultation

Should Clarence maybe drop to the floor and give your Hindass

50 pushup also?

[tvka]

Are you calling Clarence Captor replication silly?

Bad boy, not good. How do you say "Hard Head in 3 other

languages? Clarence is not going to let you call his captor a lie.

Go take readings and come back when you are serious.

No one has asked for your endless wisdom of consultation

Should Clarence maybe drop to the floor and give your Hindass

50 pushup also?

Guess pushups is only thing you both are good for!

[djarno]

Guess pushups is only thing you both are good for!

TVKa maybe you have something of my video.

Its amp building, which should be impossible because when I use on normal net power (mains) its instant amp kick in.

It's all based on clarence/barbosa. With a little difference as you can see.

If I am correct I only powered one toroid. 2 toroids gave less amps while idleing while they are the same winded. Even when I am cross connected and what so ever more.

https://www.youtube.com/watch?v=Sm-gSMGZwi4

My inverter is broken (over volt kicked in), I expect new one next week.

I'm thinking of building an tesla tower alike coil to reach over 200 kilovolt and bang an spark gap, hope it activates the ZPE field.

[padova]

This might be interesting:
Energy from the Ground - Self powered generator by Barbosa and Leal

[Alydian]

For those who are unconvinced about the ground field. an informative Youtube video at https://www.youtube.com/watch?v=Yg6G5VUSsWA. shows how little current can flow in a single ground rod even driven 50 feet deep. keep in mind this build requires potential current from the ground of at least 25 amps. to obtain 3 Kw output.

[BroMikey]

For those who are unconvinced about the ground field. an informative Youtube video at https://www.youtube.com/watch?v=Yg6G5VUSsWA. shows how little current can flow in a single ground rod even driven 50 feet deep. keep in mind this build requires potential current from the ground of at least 25 amps. to obtain 3 Kw output.

Looking at it this way 60 grounding rods at 10 feet long = .4 X 60 = 24amps.

[tvka]

Hi Djarno!

Please look at my Captor drawing from previous posts.
So do measure currents I1 and I2 and protocol them- with load and in steady state after all transitions.
No need for video.

If I2<I1- no overunity.

I do no understand how this wrapping around secondary can provide coupling. According to classical electromagnetism nothing is induced there.

Same principles about overunity I wrote to you- resonant and open system- stays.

[luc2010]

Hello my Friends,

i made the seconderies coils exactly as its recomanded, where the two tops wires is connected and the two bettom wires is connected together.

stil work on the ground rods. is it possible to use a heavy mass like old radiators, insted of groung rods?

what if we change the green wire connection and close it with the earth?

Best Regards
luc2010

[djarno]

Hi Djarno!

Please look at my Captor drawing from previous posts.
So do measure currents I1 and I2 and protocol them- with load and in steady state after all transitions.
No need for video.

If I2<I1- no overunity.

I do no understand how this wrapping around secondary can provide coupling. According to classical electromagnetism nothing is induced there.

Same principles about overunity I wrote to you- resonant and open system- stays.

More rods == less voltage drops.

Need more rods, then rewind like I did before (where the 300 amps actually drop). Though I am using 220 volts load while I get an return of 100-150 volt depending on load.

Need to wait for inverter back, and yes I haven't measured any over unity yet. Though, to me, abnormality's in an way they don't make sense.

[tvka]

More rods == less voltage drops.

Need more rods, then rewind like I did before (where the 300 amps actually drop). Though I am using 220 volts load while I get an return of 100-150 volt depending on load.

Need to wait for inverter back, and yes I haven't measured any over unity yet. Though, to me, abnormality's in an way they don't make sense.

Believe Level had sound idea- remove winding around secondary and check if there are any changes.

Abnormalities or not, the aim is real power gain. Otherwise planting of them grounding rods is monkey job.