Earth Battery SG

[Bodkins]

Hi all
New video still pulsing with the 555 to the 3rd coil (outside one) and charge a battery with the bedini setup from the same 3rd coil.
The two other coils are connected to each other with diodes to get give a direction for the movement.
In the next video the amp draw in 400miliamps at 12volts am not trying to light up the house just trying to workout how it works and i think i have it.

Once again i see movement of energy like in the imhotep light bulb stuff i have been doing. You see its a pump just like all the sg fan ect.
But with pumps you need potenical different thats where the grounded connection comes in.All you need is one place where the pressure is different and i see that before i connected the ground i get 1volt so i have movement.Ad ground and the movement is set free.

I dont now if the coil would work the same out of the ground, put it this way im not digging it up!!!YouTube - Bodkins 19 in the ground Stubblefield earth battery

[Inquorate]

Inadvertently pumping earth battery

Hi guys. This is my first post. I've been playing with imhotep fan self oscillating to 2 ignition coils. First coil primary pos and neg wired same way as battery in that config; ie neg to drive battery positive and fan radiant spikes to primary pos on first coil. Pos of secondary goes to second ignition coil Pos on primary. Neg of primary I left alone, and pos of secondary I had a wire running to capacitor to 80 v neon to two diodes, one pointing to ground, one pointing from ground. At one point, the wire from 2nd ignition coil Pos of secondary to capacitor came off at capacitor. Neon went off. As I was putting alligator clip onto cap again, cap fell over onto side. I put alligator clip down onto table, it was pointing to bottom of cap, about 5 cm away. Neon lit up. Effect stronger if two opposite facing diodes to ground. When I say ground, I mean I have soldered a wire to kitchen tap. This could be same pumping effect to earth. Also, energy transfer to cap will go thru wood, and neon brighter if cap sitting on metal with alligator clip pointed under it.

[Inquorate]

Diodes in parallel.. Will try post a schematic if not upload video to youtube. But thought the 2 diode thing and fairly high rate oscillations, etc may be relevant to post here. Maybe some pots etc to vary voltage, frequency etc, until getting max feedback..

[Bodkins]

Inquorate
Think your right i have only been using low voltant to pulse the coil.
Maybe this stuff is where the Imhotep thread is going with Hv pulse to ground stuff.
Stubblefield used tree to pulse the ground like you are seeing Top stuff


Would love to see a video of your work Inquorate more info the better.
And a diagram your setup sounds Ace!!!!!

[Inquorate]

I'll try get it done today. Ps bodkins, my missus gets all fluttery over your accent..

[Bodkins]

I'll try get it done today. Ps bodkins, my missus gets all fluttery over your accent..

[Inquorate]

some vid and pic as promised

i have another vid that shows experiment transferring wireless energy heaps well. it's stuck on a dodgey memory card at the moment . but this vid shows how pulsed dc (half wave rectified) to capacitor to neon to ground. will be brighter neon if dual diodes to earth even tho dc. forgive bad english. no sleep..

oh and thankyou for the welcome

http://www.youtube.com/watch?v=9qRkeQdCAmk

[Bodkins]

Inquorate
Your a Star
This is what i need, I have one eye on the imhotep lite and one on the earth Battery stuff.
It looks like all you need is a oscillator some good diodes,Caps and Ignition Coils and it can pull the energy out of the planet.
I think you have a Sink in the Neon, You now what i mean?Suction!Vacume! Its trying to fill the space you leftout.
Cant read the diagram so i dont now what you oscillator is, but i like it
Cant wait of the next video!!
One thing I had today is the setup run silent with two sphere.Like the oscillator was doing energy tennis???
I Maybe wroung on that one,But i hat to tell someone
Say Hello to the Missus
Dont forget to sleep

[Inquorate]

the oscillator is two imhotep fans, blades removed and superglued to makeshift stands then put in a computer power box. I had a lot lying around.. I didn't really connect them in parallel, just joined the two pos source battery leads from the transistors together with one lead out; the same with the neg source battery leads. The two charge battery pos leads with the radiant spikes are joined together and one wire out also. The negative from the charge battery out, I seem to remember being superflous, as I would be joining the charge battery negative to the source battery positive anyways. I can't remember if I left those two wires out, joined them together or wired them to the leads to pos of source battery. I'll have a look.

Also bodkins, the cases of the two ignition coils and the case of the partner imhotep fans register NEGATIVE dc voltage with digital meter to ground.. About 30v combined. So I think you're right, I've been making a vacuum of voltage. I see voltage as pure aether, and 'current' as the sideways displacement of electrons; sine waves.

The thing I noticed and have been working on is that when I was measuring the -30v to ground (which is when I noticed the two way diodes increased the negative voltage reading - this is all taken off the flipping cases, mind you..) I got distracted and held the meter lead 1mm away from my alligator clip. It sparked across the gap (yeah I know, it should take 1000v to do that) - And guess what, meter read over 1000v.

I've been fiddling with spark gaps now, filling 3kv caps with real honest to god voltage - until the gap oxidizes and voltage drops..

And that will do for now. Enuff from me for a bit.

[Inquorate]

Also... I had my meter (unconnected) within a foot from spark gap and noticed it was fluctuating wildly, showing -1 to 1500 etc. I thought, how odd. How do I damp that out a bit.. And put 1000uf 200v cap 10cm from spark gap. Meter far away connected to cap with alligator clip wires. It showed the cap as having 600 odd volts. I thought, wonder if this is a distance related thing? (meter stopped fluctuating only when heaps far away) - so I moved the cap around, and found that when cap nearer to pos wire side of spark, 600v. When on neg side of spark, closer to 400v..

Sounds a lot like the bit in gerry vassilatos' book where it says capacitors would be charged or have charge removed, depending on wether special secondary coil was nearer to pos or neg of dynamo that was supplying hv dc...

There. Signing off.

[Bodkins]

Quick word short on time
If we get a spark gap in the middle of a cap like the EV Gray Tube Patent 4595975 we have it.The tube picks up the energy and i think we get a negative pull if we get the setup right.
Got to go Take Care

[Bodkins]

YouTube - EV gray tube test 2

[Inquorate]

I've turned a glass eye dropper tube into a sealed spark tube so less oxidation, magnets to quench gap and screw as one point so adjustable spark length. Diode on other end to shut off flow of voltage in nanoseconds, and wire wound outside of tube on pos side of gap. I've been reading HHO thread, and someone there has had change in spark if in pressurized air. Also, they're finding carbon on one end of gap seems to increase radiant event. Some pots sparking on carbon points have been possible reason for overunity bedini systems. Lots of experiments to do :-)

[Inquorate]

Increasing the air pressure would increase capacitance !!!

[Bodkins]

Your Flying keep going
trying to build gap with plastic and alunium layers with magnet wire around it need some big diode.think i can get them from old microwave ovens.

one thing i will try is the negative primary of a ignition coil with a big diode to the postive secordry seen it on youtube increases the spark