Imhotep's Radiant Oscillator Video

[nat1971a]

looks like i am out of business for now....looks like water has gone over my entire system...what are the odds of that happening......just soon after i was getting WHITE sparks from my spark gap...

[nat1971a]

and the system was on....but no lights.......no where else in the entire garage except where my system was.....is that a coincidence?

[Aromaz]

YouTube - levitation melting with induction heating

Hmmm, nice. We are using such machine in our factory for three years already - heating up stainless steel for bending; takes only few seconds. Keep it too long and it melts all away. Hot energy with plenty of amps = hot energy with plenty of amps.

The challenge I have: Make things levitate without magnetic force and without melting them.

[Aromaz]

[QUOTE=broli;38152]Also something that has been mentioned quite some times here.

You can replace a component but you can't replace your eyes. So please wear protective Polycarbonate eye glasses for the many corona discharges you see that also emit UV rays.
It's really a small investment for something very valuable....
QUOTE]

I agree - and do have actually a nice UV-Auto-Shutter welding helmet in operation lately.

But: IS this light UV ??? UV is in the range of 250+ TerraHerts - Way out of our achievements with what we have. On the other hand - yes there is some form of radiation.

[Aromaz]

and the system was on....but no lights.......no where else in the entire garage except where my system was.....is that a coincidence?

NAT - Video it all before you start clean up. I regret seriously not taking a video before when I had a major disaster - like all burned out. Video in detail. Post if you do not mind. would like to look at that; and your setup prior to that; if you have video.

Please

[Aromaz]

and the system was on....but no lights.......no where else in the entire garage except where my system was.....is that a coincidence?

Was this set-up still the same you had on your last YouTube video ? 6 December ? What did you change?

I did had a few occasions where the system went suddenly quiet; then disconnect and re-connect all was fine. Now I wonder: Is it not possible the the circut went into frequency above that we can hear; and too fast for lights to lit up - then your components could not withstand the energy coming in??

Video please! Accidents like this can give us plenty of clues.

[Inquorate]

bubble bubble coil in trouble

Definitely get video. Check roof for leaks. Wilhelm Reich used this technology to control weather locally. Also, your system (coil) may have spontaneously charged with voltage and melted. Where's the oil?

[Inquorate]

Make things levitate

@Aromaz - I have some PDF books to send to you, has information on theory of that... Pm me with your email if you want them :-)

[nat1971a]

YouTube - TESLA RADIANT ENERGY WIRELESS TRANSMISSION - UPDATE 25 HYBRID CIRCUIT

Before & after video....using my original circuit...replaced connecting cables with coaxil.....generates massive white sparks

[Aromaz]

Question RE Video #019

@mrbreau PM'd me with this valid question. Pardon my stupidity not to think of this or check it that time. So I went out and set the stage as per video #019.

Aromaz? Sorry for the interruption but I have a question that has been burning me.

In one of your videos, and like you I review them often though I can't find the one I'm referring to, (I think it is #22 or #23)you have a CFL connected to a wall power supply and it is draped over a metal sheet. Though the lamp is not turned on it glows. And when you touch it, it glows brightly.

My question is this, does that lamp glow on the OTHER side of the metal sheet when the system is running?

(NOTE HERE: That light was not connected anywhere. However; I do find sometimes when all lights are off and I am looking for range of wireless - that the tubes in the roof of lab also do lit up. So with system operation; it can never be completely dar in lab anymore - unless dead short to ground)

Yes, Warren, the same light lit up both sides of that plade, anywhere and same distance from the plate. The same is also valid for fl tube as well as CFL tube. Thus, the plate does not block the energy - but rather seems to magnify it both sides. As light moves away from HV circuit (transmitter) it dims and eventually no light. Then further away but nearer to plate it lit up agian.

[Inquorate]

Prophetic signatures

Um, when I had 'I'm think we should put the unit back into operation and allow it to fail', Aromaz discovered 'broken' transistors worked again. When I had 'the best thing to hear ... Not 'Eureka', but 'That's funny' ', I discovered wood amplifies aetheric disturbances. When I had 'put aside differences and just laugh at people', bodkins had a laugh at my wearing spectacles. Now that I have Wilhelm reich quote, nat has had localized rain... that's more than half of my quotes that were co-incidentally synchronous.

''Nevermind, it's probably nothing.'' - Ben Brandwood

[Inquorate]

Nat's video

@nat your video won't load for me. It did the first time for a minute so long as I went straight thru the link (couldn't find it on blueapple.mobi) but now it's just not connecting and it's lost it's thumbnail..

[mrbreau]

Thanks for the due diligence

Aromaz? You have put to rest a vague supposition and I can now go back to deep uninterupted thinking.

I didn't want to take up valuable forum space with this question but I see now that it should have been public from the start. I'm a mere babe when it comes to this stuff though I have ideas now and then.

I really admire your works.
Warren
..

@mrbreau PM'd me with this valid question. Pardon my stupidity not to think of this or check it that time. So I went out and set the stage as per video #019.

Aromaz? Sorry for the interruption but I have a question that has been burning me.

In one of your videos, and like you I review them often though I can't find the one I'm referring to, (I think it is #22 or #23)you have a CFL connected to a wall power supply and it is draped over a metal sheet. Though the lamp is not turned on it glows. And when you touch it, it glows brightly.

My question is this, does that lamp glow on the OTHER side of the metal sheet when the system is running?

(NOTE HERE: That light was not connected anywhere. However; I do find sometimes when all lights are off and I am looking for range of wireless - that the tubes in the roof of lab also do lit up. So with system operation; it can never be completely dar in lab anymore - unless dead short to ground)

Yes, Warren, the same light lit up both sides of that plade, anywhere and same distance from the plate. The same is also valid for fl tube as well as CFL tube. Thus, the plate does not block the energy - but rather seems to magnify it both sides. As light moves away from HV circuit (transmitter) it dims and eventually no light. Then further away but nearer to plate it lit up agian.

[Lidmotor]

The Purple addiction

I just had to make another circuit to make more big purple sparks. This time I tried a simple pulse width modulator circuit (555 timer). It worked good. I hooked it up in a way to drive a CFL on the receiving coil. The only connection between the two coils is the purple arc. To anyone who has not seen and heard this magic you would not understand the facination. Aromaz I'm right with you on this one.

YouTube - PWM High Voltage Spark Generator

Lidmotor

[nat1971a]

@inquorate

video works fine for me....looks like it has been viewed quite a few times.

Theres something odd about this sparking via the insulation that has got me intrigued....i am going to continue experimenting with it....as it only works if the insulated sphere is attached...which makes me think...i am on too something....