Imhotep's Radiant Oscillator Video

[Inquorate]

Darling bodkins

when you run the first setup for around an hour, you're aligning the molecules (temporarily) of the capacitor just like when you make an electret. This is due to the back emf from the ignition coil being mostly voltage and aetheric whorls caused by streaming past electrons, streaming into the cap and sitting in the gaps between the capacitor molecules, like tipping a bunch of 1cm cubes (imagine they're only the north pole of a magnet) into a truck load of tennis balls, and shaking the truck. The tennis balls will re arrange. Take out all the magnets (aether whorls) and the next time you pour in more cubes, more will slip into the gaps between the tennis balls - less will pile up and fall over the edge of the truck.

However, give the tennis balls a good knock when there's no cubes, or just throw the odd cube at the tennis balls, etc, the balls will re settle into a less accommodating structure, so you will not be able to store as much charge again :-)

YouTube - dancing feet

[Bodkins]

I think some of this is HV from the negative of the coil too.
YouTube - 900volt charging
the kick back lights the bulb and the hv goes to the cap (I think)

Ben thats fuuniest thing i seen in a long time Sir.
Yes I had tears of Joy
One coming back at Ye

[Bodkins]

YouTube - 900volt charging

Dont forget this may just be HV spark going straight into the cap because of the BIG diode and the connection on the negative side of the secordary coil.

[sucahyo]

YouTube - UPDATE 29 EDWIN GRAY / TESLA RADIANT ENERGY HYBRID CIRCUIT Running at 60volts

greys circuit with proper cset lights cfl

Thank you . Your video show a lot.

@Bodkins, just finished watching your video, one wire lighting is really cool. I think that is proof that there is momentum in electron/ether movement.

@Inquorate, dancing feet help me release the stress after having a couple of my idea failed today . What happen to capacitor if we have more current ?

[Inquorate]

Have more current

I think it is mainly the proportion of current to voltage; more percentage of current to voltage is 'conventional' electricity, jagged sparks, magnetism and heat losses. More voltage than current is closer to what we call radiant. Associated with cold wires, no magnetism, minimal electron movement (electron bunching and voltage spikes) gas or plasma like 'spark' discharges..

With more current, actual electrons and not aether vortices get stored in the capacitor and therefore join with the atoms of the conductor. The molecules will not rearrange or become conditioned.

Sometimes if battery or cap already conditioned and even self charging with fluffy voltage, it won't hold a conventional electron charge anymore.

[Inquorate]

Catalogue of aether comments

If anyone wants to, go thru my posted comments that explain aether theory and compile them, it might be a variable resource for noobs. I'm asking because I can't copy and paste from web pages from my phone.

Big ask, I know, but maybe someone here has more time than sense :-)

[sucahyo]

If anyone wants to, go thru my posted comments that explain aether theory and compile them, it might be a variable resource for noobs.

I still puzzled with the relation between molecule, electricity, magnetism, radiant and mass. Once I understand the relation, I can help you with that.

What is solid?

[Inquorate]

@ Sucahyo

Have you read dmonarch's 'radiant matter' thread? Also, read my blog, or sift thru my posts by clicking the dot above and then 'view all posts' - if it's still not clear, I'll answer any questions you have, just pm me with them. Here's my blog link;

Deep thoughts

And if you read the w lynne book I posted a link for, just the model of the aether parts, not his conspiracy stuff, and the summary link I posted earlier - it may help.

I may write up a manuscript, but it would take time which I don't have much of lately.

Anyhoo, let me know if I can help clear anything up :-)

[Inquorate]

What is solid?

Nothing is solid, except the aether ;-)

[sucahyo]

@Inquorate, yes, I already read your post at dmonarch thread too. I will pm you my question.

BTW, anyone ever amplify the back EMF part? I tried the circuit bellow.

[Bodkins]

when you run the first setup for around an hour, you're aligning the molecules (temporarily) of the capacitor just like when you make an electret. This is due to the back emf from the ignition coil being mostly voltage and aetheric whorls caused by streaming past electrons, streaming into the cap and sitting in the gaps between the capacitor molecules, like tipping a bunch of 1cm cubes (imagine they're only the north pole of a magnet) into a truck load of tennis balls, and shaking the truck. The tennis balls will re arrange. Take out all the magnets (aether whorls) and the next time you pour in more cubes, more will slip into the gaps between the tennis balls - less will pile up and fall over the edge of the truck.

However, give the tennis balls a good knock when there's no cubes, or just throw the odd cube at the tennis balls, etc, the balls will re settle into a less accommodating structure, so you will not be able to store as much charge again :-)

YouTube - dancing feet

YouTube - Lifes A Ride
listen to what the bloke says on the radio at the end(bbc radio 6 the best channel on the planet)

[Xenomorph]

@sucahyo
Good idea, i am interested to see what you will come up with.
There is a chance that the amplification might reduce the benefit of the BEMF by losses, but that can only be said after detailed measurements.
Also just for charging purposes the voltage/current are just fine, but maybe to drive something that needs higher power?
I tried to amplify the (Joe Tate) ambient energy picked up with an antenna, but since the nature of that signal is like an audio signal, splitting it to drive the transistor weakened it way too much.
Another way, if you havent read about it (just in case) try out the Slayer BEMF booster, which is a more passive approach.

EDIT: What transistor did you use for the BEMF part? 2N3055 or BC547 ?

[Inquorate]

@ life's a ride

This thread is turning into a barn dance :-) that was well worth the wait richard.

[sucahyo]

@Xenomorph, the idea failed. It do not amplify the signal. It act as BEMF limiter instaed. Maybe because BEMF has to be split between the load and the coil or because BEMF path has to go trough electric path too. Whenever I increase the base resistance value, the voltage in BEMF part reduce and the feedback BEMF in coil part is increased. I use 2N3055 because I think it is more immune to BEMF spike. Maybe I can get more back EMF for the load if I can prevent the back EMF from going back to the coil again.

I see the slayer007 circuit, it seems interesting. I will try it later. Attached is my interpretation of Slayer007 circuit. Neon is replaced with rectifier to charge the battery. I think this would need secondary that has the same wound as primary if we want the same voltage for charging. This also can be used to charge 12V battery with 1.5V one if we use voltage multiplication property of the coil. Very interesting .

Currently the maximum BEMF I get on my circuit is measured as 160mA using 450mA input. The big problem is the input current also increase when the BEMF load increase.

[Xenomorph]

@sucahyo: Ah, too bad. Well it was worth a try. I just tried it to with a 2N3055 also but no luck.

Have you tried to use a 25 ohm rheostat (or i use a 25 ohm linear pot) like Lidmotor does? That can help reduce the input current to a sweet spot better than a 10k ohm.