Imhotep's Radiant Oscillator Video

[patmac]

As we are having daily blackouts here, the circuit is greatly appreciated...

yours have blackouts too in USA? Sorry by yours....

In Colombia president Uribe want to be candidate for third time freedom is going out.

[hh1341]

It's coming

My appetite is wet

Carl

[hh1341]

I think we should build Imhotep another pyramid.

Carl

[patmac]

Imoptep president

[**~Imhotep~**]

The Video is being uploaded now for the Radiant Oscillator lite now. Should be available soon. The radiant oscillator will be released in a week, its only 3 parts with great spikes.

Remember use your modified cfl's if you use a unaltered bulb it will be toast. But the bulb would still be good to pull the circuit out of and use it modified just would never work in a conventional light socket again.

We will start a new thread for the easy oscillator circuit, please keep this thread on track with just the light so as to not confuse. Please be careful of the high voltage, dont want anyone to get shocked. Will post again when video is done uploading and ready for viewing.

[**~Imhotep~**]

It's Arrived

YouTube - **~Imhotep~**'s Free Energy Radiant Oscillator Lite

After much work, the circuit is out. I hope everyone has fun and again please be careful. Shiva is currently working on the site and we will be announcing a date soon for everyone to come into the live chat to be able to chat and ask questions. Dates and times will be released soon. And please feel free to jump into chat at anytime its for everyone to come in and chat so we dont have to be in there. have fun

[waterhouse24]

Loved the video!!

Regarding the parts, as a lot of users will be making this device all over the world, we need to come to some kind of universal parts list.

The coil can be taken from any old vehicle?

The condensor from any pre 1983 tune up kit? presumably from the same type of vehicle the coil is from?

9 volt relay? dont have access to radio shack, any specifics needed here?

thanks for all you efforts

Lee

[**~Imhotep~**]

the relay is a 9volt dc relay contacts rated at 12amp at 120 vac or 24vdc coil resistance 500 ohm nominal coil current is 18ma.

The car coil you just have to make sure it doesn't have the internal resistance wire or ballast resistor to get the same results. That's why i chose a 1967 Camero coil because I knew for a fact that it wouldn't have the resistor.

you can use any condenser I just used one that was the best price in my area, its for a lawn mower. and the car one was 3 times as expensive.

The teaser video was ran on 6 volts which was not as bright and a hard to find relay was used that's why i changed the circuit to the same relay that Peter had used because the relay I was originally working with was from old stock and we couldn't find replacements. And Peter had good results with his. He's on the opposite side of the country than me so I figured it would be one that could easily be found. But any relay with those specs could work. as well as the coil could be changed too. And Im sure it would work. you just have to watch the contacts for heat buildup.

The setup that we have devised has ran for a half hour to a hour at a time as the bulb heats up the current draw goes down and the relay does not get very hot. Dont be afraid to experiment with what you have on hand. Just keep an eye on all your parts for heat build up. And let us know how it goes!

[ren]

AWESOME! Well done Imhotep! I look forward to tinkering with this!

[elias]

yours have blackouts too in USA? Sorry by yours....

In Colombia president Uribe want to be candidate for third time freedom is going out.

I suspect that these blackouts are happening worldwide, but no I am not in the US, somewhere around Middle-East.

[elias]

The timing of Imhotep's circuit is just right, I wonder if we could call this synchronicity or not. It is out when we mostly need it!

The video was very good. Fortunately I almost have all of the parts, I'll be replicating it soon! I just wonder about my ignition coils.

And a question, How many bulbs could be lit with one circuit? I mean we may need to design a specific coil for lighting around 10 light bulbs, to illuminate the whole house. May we not?

Many Thanks!

[riccardom70]

the relay is a 9volt dc relay contacts rated at 12amp at 120 vac or 24vdc coil resistance 500 ohm nominal coil current is 18ma.

The car coil you just have to make sure it doesn't have the internal resistance wire or ballast resistor to get the same results. That's why i chose a 1967 Camero coil because I knew for a fact that it wouldn't have the resistor.

Hi, optimal job but the circuit how much consumes in energy? I explain myself better, regarding the circuit that you have removed on the bulb neon is an inferior consumption? Thanks

[Tecstatic]

Thank you for sharing this, and thanks to all in this great forum for giving a lot of information.

I have been lurking around for some time. trying to digest a lot of material about alternative energy. I'm an old EE, but feel humble to all this "new" stuff I never learned about in school.

Although I am very busy with my work for a week or two, and have no suitable ignition coil, I just could not resist making this circuit. I took a roll of 0.25 mm magnet wire and added a primary and some welding rods and the remaining parts.

It works with same consumption, but not the light is not so bright as on the video. When I have done my ordinary work, I will try to improve the circuit. It would be nice if it is possible to make some semiconductors replace the relay, so the long term reliability can be improved.

Eric

[robur]

i hope my friend in Zmbabve can use it. they cannot afford fuel for all village only for the chief's house and his family the rest use candles. they have car batterys but that is it.

But i do have a question-Can this be converted to the AC? What type of bulb is it exactly? If it is only LED light this is very little energy. What bulb type wattage and is it AC OR DC one

thanks

[**~Imhotep~**]

Thank you all for your questions im working really hard to get the documents in order and will be posting the schematics here. Its been a very long week so if I dont get to all your messages really quick please bear with me I will try and respond to everyone as soon as I can.

The circuit is removed from the fluorescent because it is what causes it to draw the energy, what we are doing is sending the electricity through the gas. which drops the current it draws.

In my experiments one thing that we noticed was the the cfl drew alot more current than what they said they did. For example : If you have a 75 watt light output cfl that says it draws 18 watts what it really is drawing from the power company (what your paying for) is double that. A quick experiment to test this is to get a hold of a kill-a-watt reader. And take a lamp and hook up a cfl, plug the lamp into the kill-a-watt and read the power factoring. A 18 watt will actually draw 36 watts. We were quite astonished.

I have only been able to light up one bulb with the circuit, I have tried experiementing a bit with lighting more, but so far havent come up with a way to do that. But I am sure someone here will get that worked out

You are using pulsed dc but if you use 2 coils and 2 relays it is possible to convert it to ac, we are working on other circuits now but im sure with some experimenting it could possibly work.