Hendershot Replications

[pjotterkjen]

Drill template for 57 pegs Hendershot capcoil MK3

For the ones that are interested, while looking for MK1 stuff, I found a drill template scale 1:1 on overunity.de for the 57 pegs of the MK3 device, if this already has been shared my apologies.

Free Energy - Freie Energie - OverUnity.de

[pjotterkjen]

Transformers were not critical according to Arthur Aho

Transormer Z1900 Universal (Bracked Furnished). He fits!!! This is very important, otherwise the generator will not work!!!!!!!!!!!!!!! No one does not have a working model of the generator Lester Jennings Hendershot. Must exactly to do otherwise will, not work nothing!!!!!!!!!!!!!!

N20Wolf, Arthur Aho, who has personally worked for 2.5 years with Hendershot himself (1958-1961) and built 5 different devices and conducted a lot of testing, mentioned in his writings that the transformers were not critical.

You were asked politely to publish your own results... so if you have it please come forward with it, there's where you can gain credit on this forum.

[N20Wolf]

The illusion is again before our very eyes:



This is what happened when I was doing a polarity check.
The small Neo used in this 'magnet' is sitting on my Neo stack.
The small Neo will only come out if the correct opposite polarity or attracting Pole is presented to its face.
I thought the little protruding ends on each side were part of the mould but not so.
These little Neos measure 5 x 7.5 mm and my extraction 'tool' is 6 x 12.5 x 4 mm, 24mm.
I was unsuccessful in attempting to parallel the arms and now I know what is inside creating the 'magnetism' I can extract both Neos and simply apply some heat at the bend and it will straighten just like in a Smithy's shop.
Didn't want to do that if it was magnetised.

These were going to be used for the Wesley 'Neutral Zone' motor.
Not what I call a Magnet as the one on the LHS, source unknown and the one I am using in the Hendershot replication, out of a a vintage speaker.

N20Wolf,
All you appear to be presenting is material that I already have and you appear to have some discrete knowledge of the device as if you have one working and don't believe that is the case.
Do you have a working unit and could we please see your pictures and some more detail and not something that we already have?
The Russian Hendershot Forum also I do not believe has a working unit, just a great deal of information which again, as Graham has stated, you cannot model on your Computers.
I am currently running through the Russian Forum data but have not seen anything there that suggests a working replication as nobody is jumping up and down saying 'I have it working'.
Just the facts please and not just more confusing information that is distracting.
Thanks.

Smokey

Hello In Generator Lester Jennings Hendershot Use transformers with windings 5 to 1
See this picture:
http://realstrannik.ru/media/kunena/...-10_053550.JPG
Transormer Z1900 Universal (Bracked Furnished). He fits!!! This is very important, otherwise the generator will not work!!!!!!!!!!!!!!! No one does not have a working model of the generator Lester Jennings Hendershot. Must exactly to do otherwise will, not work nothing!!!!!!!!!!!!!! Coil in buzzer used from ringer just about 110 volt

[GSM]

You smokin David ?
ie. burning the midnight oil ?

http://www.energeticforum.com/renewa...tml#post248545

Cheers ........... Graham.

[David G Dawson]

Picture Size

Apologies for the really big basketweave picture but edited x3 times and it remains unchanged
Image Shack have updated their site and the image I got above for the Magnets was for 'Forum' but is now the opposite, too small.
If you click on the picture you get the bigger size but also all of my Album pics which is OK.

Smokey

[David G Dawson]

The Magnet Illusion

The illusion is again before our very eyes:



This is what happened when I was doing a polarity check.
The small Neo used in this 'magnet' is sitting on my Neo stack.
The small Neo will only come out if the correct opposite polarity or attracting Pole is presented to its face.
I thought the little protruding ends on each side were part of the mould but not so.
These little Neos measure 5 x 7.5 mm and my extraction 'tool' is 6 x 12.5 x 4 mm, 24mm.
I was unsuccessful in attempting to parallel the arms and now I know what is inside creating the 'magnetism' I can extract both Neos and simply apply some heat at the bend and it will straighten just like in a Smithy's shop.
Didn't want to do that if it was magnetised.

These were going to be used for the Wesley 'Neutral Zone' motor.
Not what I call a Magnet as the one on the LHS, source unknown and the one I am using in the Hendershot replication, out of a a vintage speaker.

N20Wolf,
All you appear to be presenting is material that I already have and you appear to have some discrete knowledge of the device as if you have one working and don't believe that is the case.
Do you have a working unit and could we please see your pictures and some more detail and not something that we already have?
The Russian Hendershot Forum also I do not believe has a working unit, just a great deal of information which again, as Graham has stated, you cannot model on your Computers.
I am currently running through the Russian Forum data but have not seen anything there that suggests a working replication as nobody is jumping up and down saying 'I have it working'.
Just the facts please and not just more confusing information that is distracting.
Thanks.

Smokey

[N20Wolf]

These guys have it working so they say 450 watts

Бестопливный генератор Хендершота (обсуждения) • Форум проекта Заряд

I do not know this generator works or not. I wrote this on the forum ...I said if it is possible to earn maximum power is 450 watt

[Gazzasore]

These guys have it working so they say 450 watts

Бестопливный генератор Хендершота (обсуждения) • Форум проекта Заряд

[N20Wolf]

Hi Wolf,

I have not a clue what any words mean on your own forums, but on this page link above, it looks like some members are attempting to computer simulate an impossible to simulate Hendershot Generator circuit, at which point I muttered "f-f-s!" to myself and flopped back in my chair flabbergasted and shaking my head !
Okay, you might uncover some ideas relating to frequencies, but computers are linear/quadrant calculators, whereas Lester's generator is not.

Why is the magnet in Crusty's picture shown as N-S-N ?
Did Hendershot himself not indicate the magnet was plain N-S ?

That looks like a cast magnet, so could the centre bump not be where the molten metal was injected into the mould ?

Look at the 2x magnet coils resistance - were they not circa 9 ohms ?
Look where these coils are connected to - medium value 'C' plus a low ohms transformer winding.
How could anything but a high power plain N-S magnet cause that armature plus twin coils assembly to have any pulsatile relationships with the lower impedance circuits ?

Cheers ............. Graham.
.

Well, in the schemes generator have exactly the error!! Specially made. One man said that there schemes generator error!!! I do not know whether it will work at all generator.

[Beamgate]

@Graham,

Did you get far enough along on the realstrannik.ru/forum site to see this?

It's amazing what poor translations, transcriptions (and patent attorneys) have done to the Hendershot legacy over the years.

I'm still reading through all of their recent revelations.
Fascinating stuff

[GSM]

Hello!
See corrected schemes here (Russian Forum):
Форум]Форум странников :: Тема: Бестопливный генератор Хендершота (28/38)

Hi Wolf,

I have not a clue what any words mean on your own forums, but on this page link above, it looks like some members are attempting to computer simulate an impossible to simulate Hendershot Generator circuit, at which point I muttered "f-f-s!" to myself and flopped back in my chair flabbergasted and shaking my head !
Okay, you might uncover some ideas relating to frequencies, but computers are linear/quadrant calculators, whereas Lester's generator is not.

Why is the magnet in Crusty's picture shown as N-S-N ?
Did Hendershot himself not indicate the magnet was plain N-S ?

That looks like a cast magnet, so could the centre bump not be where the molten metal was injected into the mould ?

Look at the 2x magnet coils resistance - were they not circa 9 ohms ?
Look where these coils are connected to - medium value 'C' plus a low ohms transformer winding.
How could anything but a high power plain N-S magnet cause that armature plus twin coils assembly to have any pulsatile relationships with the lower impedance circuits ?

Cheers ............. Graham.
.

[N20Wolf]

This is one instance of where to obtain the Bell Ringer Coils, from vintage Wall Telephones.
On the left is one from Western Electric and coil from this has gone into the CRD, see bottom pic below.
On the right is an Ericsson (Swedish but manufactured in Sydney) and is dated 1920 and would assume the WE is also in the 20s.
On the right is its Bell Ringer Coil which is the one I am using on the Hendershot carriage.



Uploaded with ImageShack.us

Have just purchased these from Ebay to be used below as an optional Bell Ringer.



Uploaded with ImageShack.us

This is where The Western Electric coils went into - this is Eric Dollard's 'Crystal Ray Detector' (CRD) but may change for one with a greater donger arm movement as am having difficulty as this is used as the switch to reset the Thyratron.



Uploaded with ImageShack.us

Will go and pick out some pictures of my Hendershot build of this device as it may be of interest and assist others.
Bottom line here is to make a Gary Wesley 'neutral zone' replication as this has been the missing link and if successful may venture into the Motor which is fully described in the Harper Magazine article.

Was going to use the Magnets from the Ericsson Magneto but might be too large and have bought 4 x 4" Horseshoe but would have liked 6".
These do not have parallel sides but don't see why a little gentle persuasion can't make them otherwise.

GSM (Graham Maynard) has been very helpful here in making up my mind what to do next and has confirmed what I have been missing as being Wesley Gary's 'neutral zone'.

I should also mention here that the favourite ohmic value for each Coil is 500 ohms and this has become typical of all that I now have.

Smokey

Hello! Please see foto:
http://imageshack.com/a/img843/9814/g4oa.jpg
http://imageshack.com/a/img801/2497/uxhk.jpg
http://imageshack.com/a/img690/2489/pdxv.jpg
http://imageshack.com/a/img594/3407/53ua.jpg
http://imageshack.com/a/img855/6420/3ngk.jpg
http://imageshack.com/a/img7/3125/o6io.jpg
http://imageshack.com/a/img834/3693/oa5e.jpg
http://imageshack.com/a/img836/2371/p5k3.jpg
Buzzer to be two plates.
See this Document:
http://realstrannik.ru/media/kunena/...BRAJEN_ENG.pdf

See corrected schemes here (Russian Forum):
Форум странников :: Тема: Бестопливный генератор Хендершота (28/38)

Need to adjust the antenna homemade exactly!! And then after setting the pour paraffin between the antenna and the coil.

[GSM]

Wow David.

Take just one of the top left magnets in this image -
ImageShack� - Online Photo and Video Hosting

and fit it with say 5mm neodis (or 2x 3mm) just fractionally larger than are the poleface ends, and you will have an ideal Wesley Gary replication magnet.
Those neodis can go either on the ends or the pole sides to use as Wesley did, but his magnets were not as good as ours and so on the ends are where I would recommend.

Then to replicate Gary's field reversals find something like an old 500 to 2000 ohm telephone service coil - on its own - and fit it with a pair of back-to-back reverse connected LEDs.

The neodis will extend enough field outwards from the magnet poles for you to transduce the same field reversals as Gary did 135 years ago, this even with field passing through the end of the coil winding without need for separate unwound armature poles.

Then with coil springs or fine foam fabricated between the coil and magnet poles, you too will be able to generate back-EMF free electicity with an unbelievably negligible drive force requirement.

Bottom line here is to make a Gary Wesley 'neutral zone' replication as this has been the missing link and if successful may venture into the Motor which is fully described in the Harper Magazine article.
Smokey

and what an eye opener it WILL be David.
(Much lower resistance/impedance coils plus much faster field reversals are of course necessary to generate more power.)

As you can see from the other Hendershot thread I, like yourself, had studied much in an attempt to unravel Lester's generator, also see my Dailmotion video where I had demonstrated the basic Wesley Gary effect at the end of 2012. Through 2013 I got nowhere at all with Hendershot's design but I did enough more with Gary's to know of its potential usefulness. Then, whilst lying thinking and recovering from illness at the end of 2013, I suddenly realised this exact same Gary effect could have been induced through the twin 'tin can' cores within Hendershots generator !
Then Duncan just started the TPU thread as well - a circular plus purely inductive electronically energised 2x Gary type design, but you know what - out of all of them still I prefer Wesley's arrangement, with neodi magnets and just a little bit of basic electronics to render the construction entirely motionless.
Also - non of this is down to aetherial conjecture by anyone - it is an already known plus *Patented* magnetic field related phenomenon !

Cheers .......... Graham.

[David G Dawson]

Hendershot Build Pictures

Hendershot Generator:
Have put this back together as an Interim Build just to show the oveall layout as I did not have a picture with the Resonator carrier intact.
This is the Ericsson coil set.
Carriage actually has a rubber band stretched back to a screw in the board to keep it from actual contact with the Magnet.



Uploaded with ImageShack.us

Completed basketweave with L1 in place and the sister to the cap I used for an initial condenser build and which was slightly damaged but worked well and this was out of an old Blaupunkt TV and I happened to have two.
The original caps were replaced with the nonpolarised 40 and 80uF.
All coils wound from right to left around the rear or CCW.



Uploaded with ImageShack.us

This is the Ducon 500uF 350VDCW capacitor I used for the home-made and all I had to do was cut in two and rejoin back with output terminals.
Measures 100mm long with dameter of 63mm.
The capacitor when sawn open was obviously place into a too big a can and hot bitumen was used to centre it and suggests the can was designed for a 1,000uF but did the job regardless.
The remaining bitumen was able to be removed without problems but had to be heated on a hotplate before the cap could be removed from the can.
The terminals are aluminium piedish cut so that it could be folded over and then is slipped over the open end of the thin aluminium foil that makes up the plates and is then punched with the scriber to make solid contact and worked well and this is very similar to what the manufacturer actually also does.
Apologise for not having a pic of the entire operation of making the condenser but is laid out over a 2m bench front with a little overhang and this also worked well with freedom to move.



Uploaded with ImageShack.us

This is the actual Capacitor used for the build with the Greaseproof Paper used as the insulator and was found easiest to use a small saw to cut the paper - 1 layer only used.



Uploaded with ImageShack.us

Hope this is of interest to other builders.
Thanks.

Smokey

[David G Dawson]

This is one instance of where to obtain the Bell Ringer Coils, from vintage Wall Telephones.
On the left is one from Western Electric and coil from this has gone into the CRD, see bottom pic below.
On the right is an Ericsson (Swedish but manufactured in Sydney) and is dated 1920 and would assume the WE is also in the 20s.
On the right is its Bell Ringer Coil which is the one I am using on the Hendershot carriage.



Uploaded with ImageShack.us

Have just purchased these from Ebay to be used below as an optional Bell Ringer.



Uploaded with ImageShack.us

This is where The Western Electric coils went into - this is Eric Dollard's 'Crystal Ray Detector' (CRD) but may change for one with a greater donger arm movement as am having difficulty as this is used as the switch to reset the Thyratron.



Uploaded with ImageShack.us

Will go and pick out some pictures of my Hendershot build of this device as it may be of interest and assist others.
Bottom line here is to make a Gary Wesley 'neutral zone' replication as this has been the missing link and if successful may venture into the Motor which is fully described in the Harper Magazine article.

Was going to use the Magnets from the Ericsson Magneto but might be too large and have bought 4 x 4" Horseshoe but would have liked 6".
These do not have parallel sides but don't see why a little gentle persuasion can't make them otherwise.

GSM (Graham Maynard) has been very helpful here in making up my mind what to do next and has confirmed what I have been missing as being Wesley Gary's 'neutral zone'.

I should also mention here that the favourite ohmic value for each Coil is 500 ohms and this has become typical of all that I now have.

Smokey