Donald Smith Devices too good to be true

[med.3012]

My personal opinion.

He said

The primary has to be located within the Bloch wall area, dead
center, and, at a 45 degree angle to the secondary to function.

Hello BRO!

thanks for the valuable contribution, can you please explain the 45 degree ? in my opinion the max electromagnetic flux can be obtained when both primary and secondary are parallel to each other, this mean the angle have to be 0 ! ?

[BroMikey]

Hello BRO!

thanks for the valuable contribution, can you please explain the 45 degree ? in my opinion the max electromagnetic flux can be obtained when both primary and secondary are parallel to each other, this mean the angle have to be 0 ! ?

Not Sure Med, maybe he means this.

[med.3012]

Now Sure Med, maybe he means this.

Thanks Bro,


it seem to be a cleaver method, this give an unbalance in each direction so there's a kind of separation between magnetism and electricity, it worth to be tested, thanks once again

[BroMikey]

Thanks Bro,


it seem to be a cleaver method, this give an unbalance in each direction so there's a kind of separation between magnetism and electricity, it worth to be tested, thanks once again

Yes I agree, it reminds me of the DYNAFLUX rotor wobble.
In the DYNAFLUX the rotor is on an angle like these coil winds the
difference being one field is rotating on an angle the other field does
not move.

The interaction on both are similar looking. Just a guess.

[BroMikey]

Thanks Marc

Here is the first step of a Don Smith Device.


Published on Jan 19, 2016

Showing ambient energy or cold electricity draw from ionic source.
Source uses 9.6 watts to fire the ZVS and light a 20 watt led
without being able to measure voltage with a low frequency energy
source.


[VIDEO]https://www.youtube.com/watch?v=0tM2WP3E_KM[/VIDEO]



Marc Belanger 2 days ago
the frequency is too low to.be rf, however, my circuit isn't in
resonance so I only get close with the right spark gap,
unfortunately, the one that works to create resonance burns
out too quickly and it's rated for 5000 amp max discharge and
2700 volts , but, I.don't exceed 1280 volts input. the coil is built
to resonate at 30077 hertz but the output of the zvs and fly back
is much lower. this varies with the spark gap, how quick the
pulses are, etc.

the reason the ambient energy is induced is due to the coils
being close to resonance. the electrons in the primary coil
are dancing around by the pulses, and, the key to.getting
this to work is to have both in dipolar resonance so they both
have the electron movement. once they get the movement,
the secondary will operate and energize a load.. the closer
to.resonance, the more electricity comes out, however, science
declared a long time ago that there's only two.types of electricity,
amperage driven, which this is not, and static, again, which
this is not. this is cold electricity drawn from the ambient within
the secondary pulse because I'm driving the coil close to it's
natural resonant frequency. If I tune the secondary and connect
the correct capacitor, we can get exactly the input energy for free,
or many "mirrors" or copies of this energy amplified by what's
called phase conjugation.

this is not drawn from radio waves, there isn't 20 watts of power
to pull in down in my basement from radio.towers.. after finished,

I connected 12 of these leds, and they were all the same
level of brightness. I then connected a 50 watt led, turned it up and
smoked it. then, my arc gap came loose, I.connected it live and
it blew the ,20 watt led like a bomb. the amperage is devastating,
so, no, it's converted here within the circuit and outputs more
than in.by Earths flux, or something like plasma tubes.


Kangsteri 1 day ago
+Marc Belanger Well this is hard to explain easy, but here is
some of my current speculations with bad english... It could
be that the spark gap makes the circuit act like "solid state
stirling engine". So it doesnt use the traditional electrical
energy from the source, but it rings / moves the natural
energy in the circuit and its mass. So it doesnt create a
nything, it just boosts the natural movement of electric atoms
in the mass. Or it could be creating negative / positive state
to the circuit and the natural charge in the atoms of the mass
try to fix the balance. This could explain why it usually gets
cold too, if it sucks the needed current from the air atoms.
Tesla mentioned that it has similar state of matter than gas and
it might make similar hissing noise... On many "free energy"
devices the key element is some kind of tank circuit or the mass
of it all and tuning it. This means the size and relation of the main
circuit to rectifying circuit, coils, inductors and capasitors, and
the size of them. Coils and specially inductors seem to be often
very underrated thing in the circuit, they also store and give very
much power. I have made some tests on different style joule
thiefs and joule ringers too. To me they seem to act like
"ram pump", that can store, boost and limit the current. And
there would be very much improvements to be made in different
shapes and materials of the cores and wounding methods.
The Lasersabers "super joule ringer" is very special in this case.
It seems to work with small neodymium magnet core too. But i
need to make tunable capasitor and more tests with that, and
the polarity of it. I hope this makes any sense.



Marc Belanger 1 day ago
Yes, it makes sense to me, especially after I read Tesla's entire
high frequency section and tuning for resonance very recently
again and again, over and over, purely some deep form of
fascination I have had for electricity of a unique nature... I
even read about Tesla's fascination with electrical and lightning
as a child and it reminds me of myself. Since my father was a
lineman and became a master high voltage cableman , starting
his own business in the early 70's, I wanted to always do what
he did. At early ages, both myself and my brother had no fears
with the electric system and played with it often, electrocuting
ourselves and still not ever being afraid of the sources, not even
that of high voltage systems as we grew up. We both joined
the IBEW and the CT apprenticeship to learn a trade working
with high voltage cables, within transmission and distribution
systems. We have taken over the business and now run all of
the operations now for years, however, I have been experimenting
with power systems now for nearly 18 years, all types of
alternative energies, which I have found many ways to do
with hv and low voltage electricity was was thought to be
impossible now for the last 5 to 7 years. It seems that everytime
I lay down and try to sleep, I think about this and other options
for my experimentation that would me to rearrange the non
working experiments I am working with, just to get a special
feature or unique outcome, and, there are so many possibilities,
to me, the challenges are endless. I never give up with a
project I am working on until I am satisfied with the outcome.
I leave the projects together even if they don't work, then,
I go back to them once I see a vision of a new idea that works
to make something happen so it functions, then, I try it.
The visions usually portray a way to make the system work,
but, they never function the first time, I always have to wait
and go back to them time and time again!! I saw a vision in
my dreams last night,
and I feel I have actually found the correct arrangement
to use for the circuit I am working on, however,
this circuit is not Don's because it is my own arrangement.
I was told in the dream how to make it function, but, I will
have to use now a very high voltage and high current IGBT
or Mosfet for switching so the current can be connected and
disconnected from an isolated circuit to cause this high
amperage discharge in the secondary, enough to charge the
caps and battery to use for a massive gain in energy for
self looping and to do heavy work.. If you remember what I
stated about the arc gap, When I connected the arc gap
after it fell loose, I used a pair of insulated pliers and tapped
it to the source where it was fed, allowing a burst of HV to
get rectified and shoot through the coils, getting to the other
side in a very strong burst, but, nothing more than this other
than the exploding led chip. It caused a high powered blast in
the secondary that was startling, I mean it sounded stronger
than a shotgun blast and I literally jumped! . This blast was the
led exploding as loud as a 208 volt phase to phase explosion,
however, when the spark gap is connected normally, there isn't
enough of discharge from the secondary to do anything but light
the leds, however, I could light as many leds as I wish, with no
ill effect , or any use of energy from the source, in fact, the
energy used was reduced! I tried this again, and, the next time
I tested the output voltage and it was tested ok with the analog
meter which jumped up to 240 volts. I could tap the connection
together 5 times instantly and all 5 taps gave me 240 vac. I then
rectified this and it made 320 vdc, but, I decided I am going to
use an igbt or a mosfet to connect it after I isolate the control
for the igbt or mosfet and power the switching circuit from a
battery source that is unrelated, using a 555 to pulse it on and
off, creating this energy burst 60 times per second, then, transform
it to a lower voltage to see if it will charge batteries. I know it
will work, I saw it in my visions working, and, that is when they
all work perfectly. Oh, BTW yes , you are 100% correct, this
energy that powers the leds seems to be smart, like it has a
mind of it's own, knowing what it will blow up or what it will not..
I actually am able to feed my cheap and old laptop with it
and it turns on, however, it will not charge the battery. I am
trying to figure out something and would like to see if it needs
rectification to feed the battery first, and, if it does, we won't
need to go any further. This means we can charge batteries,
then, use the battery to feed large ultracapacitors for load
handling, and, fire up powerful inverters. The energy, touched
by a human has absolutely no effect.. add a light bulb..
no effect... add a neon no effect... add the led , or as many
as we wish and it or they lights up, but, these aren't low power
leds, these are chip style flat leds that won't light without
50-100 volts and 50 watts, or, 12-24 volts and 10-20 watts
consumption. But, the circuit will power up as many as I can
connect to the circuit. it will energize the same brightness on
all of them as well. I connected all of them tonight in one shot,
then, I connected 20 of the 1 watt leds in series and parallel
without popping them. I connected a 4' flourescent bulb to full
brightness and the load drops to zero when it does this. There
is no hv according to the oscope too. It is very strange! Thank
you for your interest. If you wish, ask me to connect items and
I will video them for you before I change the circuit I'd like to
keep it for testing. I am going to bring this out to Yale University
for testing soon, I would like to make an appointment for a visit
and possibly have their students do a study on it if they wish.
I do a lot of work at Yale currently and have a friend that told me
he would be able to get me in the door for a physics study as he
did once before for another project..

[BroMikey]

Marc Belanger Continued








Marc Belanger 1 day ago
.........
...............
The circuit is an experimental reversal of Don's original system.
He has given the wrong diagram, but, the info is out there to
make the system work, along with my interests in making the
correction, posibly even showing a complete diy if I don't receive
what Ive been after.. . anyway, don't keep shouting doubt..
your doubt won't stop me from succeeding in doing what I am
trying to do. I have several of these boards made up and two
of them have pretty promising results, the battery even
overcharges, the whole nine, I am just waiting for parts to
even out or reduce the battery's overcharging.. when they
arrive, the questions I had will be answered, especially the
Metglass core and the asymmetric transformer wound with
Litz.. It works like a charm.. There's a few other devices that
are already functional in my lab, so please, don't try to add
the suppression to my channel.. I've already passed your
level of negativity and have made it very positive for my
viewers. The big problem is that there's too many flies out
there seeking **** and, I've found that I get a lot further
helping others privately than posting any of the answers
to the public. You know as well as I do that I can't post
the reason why it all does what it does publicly ,and,
that Public posting has taken a lot of true innovators that
have figured out the reality of these devices offline and
made them go away for good. . I'm not one of them. I've
taken the impossible and already made it possible. What
makes you suggest that I can't do it again? That is my only
wish here.. is to show folks something is possible so they
don't give up. If I weren't in business with the power
industry, I would have already pushed these devices to
the private market, on the underground because there
aren't many able to take apart what I have built to be able
to replicate it and then tell you how it functions correctly.

That is the entire key to this all. if they could say the answer
with certainty, then they can build it, but, until that time
comes, everybody thinks this is a step up system that
magically collects ions, slices the energy and outputs magic
from the high frequency area.. which it can't and won't do..
it is what I am showing here, minus the special compound,
however, this can't be in resonance because it doesn't have
the metallic rod needed to make it all happen... I have, and
have had a similar metal compound available to me for years
that absolutely makes it function.. should I REVEAL?? remember
my key is similar in structure, but isn't the same, however,
it does and will continue to self operate no matter what you
or anybody else says. I just haven't posted mine because the
frequency isn't stable or in the correct range yet. It will be
very soon though, unless i receive what I've been asking for.


Marc Belanger 1 day ago
Unfortunately, cold electricity is immeasurable without the use
of a scope. In fact, I think I've proven this in my video to
show it only shows up as negative energy from a scope,
which doesn't happen in dc electronics. But, i will happen
to make it easier for all by offering a negative energy to
dc output by trying to rectify when I get back to the lab
this evening, seeing if it will successfully rectify and output
to charge batteries or a cap since the energy will not
charge ultracaps directly, but, it may only be because
the ultracap works more like a polarized electrolytic cap
and will filter out high frequencies, eliminating flow of
energy completely. I just think it is also too weak to do
so, however, when I remove the arc gap and reconnect
with a tap using a set of pliers, the led blows up like a
bomb, and, it makes no sense since it isn't a solid
connection, it is an open connection that gives the
oscillation of the tank circuit time to charge too high
and amperage build so high that the output ends up
exploding with mass amperage for a split second.
Anyway, this shows the true potential of the system
because it shows me one of two things.. I am using the
arc gap in parallel to the rectified input, then, charging
a cap in series to create a charge pump, however, I
need to do just the opposite and create a steady dance
of electrons as an input while the cap is already charged
in parallel to evenly release the strike of the arc in a
steady but silent motion to output as a massively an
increased output. This is easily done with a special
metallic compound, however, I can't give this up, I
am trying to find the way without it.



Marc Belanger 2 days ago
+dusanln Don's system is a protected system since it was
bought out for it's use, and, the majority of the technologies
were bought to be shelved. The information being listed online
will attract the wrong kind of attention, but. I certainly will
assist you, however, what folks think are the parts, aren't
really the same parts needed for every system. Every coil,
whether they are B&W's coils or not, air dux, or other brands,
even the same brand and model numbers will have a bit
different resonant component. We have to tune accordingly,
and, even the formulas used all over for Rf are not really the
true formulas, the formulas are literally specific for this device
and must be specifically comprised of two different mathmtical
equatins si. I am going to share one secret right now with you
all... The primary has to be the larger coil, and, the secondary
is a split coil, it doesn't have to be opposing coils, but, they
do have to be multiplied x each other's turns to get what you
need for primary turns. Also, the insulation of the primary
between each turn needs to be calculated "the space" needed
to calculate the resonant uf. at the same ratio as the turns
ratio from primary to secondary. Spacing equality is vital, and,
you need to have at least 4 times the primary spacing between
leads to catch a break with resonance with the mutual
inductance as it is vitally important to receive this for an
amplification factor. To make the tie physically will give an
amplification by way of "forced resonance: of the overall
inductance and turns, as Kapanadze does, however, the
coils of his feed into each other and aren't mutually
inducing from one to another by way of matching frequency
due to the same wavelength's oscillating without touching
each other, allowing the dispersement of electrons marching
in one coil, in the same direction as the other coil. This is
the whole magic trick with the Don coil system and it was
discovered by Tesla.

[mikrovolt]

The bent coat hanger is fashioned to represents it's fractal role.
Which is that part of a network to filter direct and converge the unobserved energy.

[BroMikey]

Here are some shots of Marc B. device replication of Don S.

You will notice the primary coil of 140 turns? I think that was the
number of turns, is on a 45 degree angle inside of the secondary.

Marc talks more about the Antenna. The pictures shows the angle.




Marc Belanger 10 hours ago
+Bro Mikey Thanks BroMikey. I have finally figure out
how the system induces the energy, and if we look at the
Don images of his benchtop generator, we see a tube
internal to the generator that gives us exciting news
showing me and the world that the North side of the coil
has a core, or, an antenna core, which would be similar to
Kapanadze's but, used for a different purpose. Don spoke
of the use of different core materials used in his Dipole
generator, one of them being a milspec metallic compound
that acts as an antenna, not as a magnetic core since the
material is not ferrous whatsoever. We would connect this
core to the arc gap side of the ground, at the NST,
introducing a pulse of ground to the core's antenna rod.
I find that aluminum acts as the best energy antenna, so,
if we pulse ground spikes through to this, there is an
energetic comp[onent to it, creating an attraction from
the aether , back to this antenna. Since the coils are wound
around this, for the magnetic energy to get back to the
antenna, it has to go through the coils first. We show in
my video that the aether's cold electricity is excited in the
secondary coil, ready to go, awaiting for the magnetic
energy component to hit it as it is in partial resonance.
The harmonic that is already there in the secondary is
ready to induce anything that would flow near or through
it as an electrical energy derived by the magnetic
component as the coil is charged, but, it isn't yet
energized. Since the antenna is attracting the Earth's
plasma tubes to the system, when we ground the other
side of the load, the charge pump has been pumping this
pulse of enrgy into the ground, and upon it's realignment
to the antenna core, this energy will start to flow as the
pulses start to migrate from the ground, back to the
secondary coil, completing an operating circuit. I really
feel this is the answer and I will be providing my work on
this to see if I could get the energy to flow this weekend,
provided I could provide a new and better ground to the
charge pump, and, the higher impedance ground will have
to be the load's return ( i think, I may have it backwards,
but, if it is, it will only require changing two wires to see
if the current starts to flow.) i will keep you all posted.
It won't take much to get it going as I built 2 new coils
with fine stranded copper clad aluminum 1/0 wire as the
antenna core last night and will be testing them later
today!

[BroMikey]

Doc E says it works also.

The tube video guys are a mess when it comes time to
explain what they are doing. I remember way back watching
some make statements that the voltage is stepped up but
"SO WHAT" and I would go to the next video.

They always fumble the ball when it comes time to tell
someone else what is going on. Doc E did a bunch better
than what I have witnessed. Answers like more voltage
comes out just doesn't say it.


[VIDEO]https://www.youtube.com/watch?v=tyW5TYyx-k4[/VIDEO]

[Force2B]

Hi, All,

For my very first post on this forum:
I have been looking at the picture of Tesla's apparatus, as well as a few years research into the whole 'free energy' stuff. Interesting. Sometimes I recall Johnny Cash, because 'I've been everywhere, man' on the 'net researching and reading about a whole lot of what I believe to be working technologies that have been suppressed by the so-called 'elite'.

I have not experimented with any devices yet (only for fear of burning down the house, or being shocked to death that I got something working :-D).

Right now, I am into research and ideas, including Eric Dollard and his postings here.

For my very first reply on this forum:
@ Jeff Pearson,
In studying the photo, and my knowledge of drawing, I believe the little squiggly you see in the circled section of Pat 568,178 is a 'hidden line' depicting a rod through a hole to hold the rod attached to a plate, and the thick portion is a sliding collar to allow the movement of the plates to vary the space between them.
I had to look at this a few times, because with Tesla, sometimes it's hard to see what he was doing.

I wonder what ever happened with the guys that were trying to replicate the Lockridge Device? I've had some thoughts and ideas on that as well.
The posts about Syairchairun's device is interesting, and there's a few that are working on that one, too.

Anyway, a VERY BIG THANK YOU TO EVERYONE who is willing to share their ideas, findings and concerns.

TheForces2B

[BroMikey]

Greetings Force2B and Everyone to whom this may concern.

Here is a recent entry I feel it very important for serious
experimenters. Thanks Marc for sharing your work that has
required long investigations through the years.

Not only does Marc understand how to do this for himself
he is also well able to explain to others what is needed.
This is an important addition for replicators.



Marc Belanger 6 hours ago
+Bro Mikey I have had luck with one of my first replications of the
schematic Don supposedly released. There are like 7 diagrams
from Transworld Energy, Don's company before he passed away.
He must have made a bunch of the circuits work, however, he
would show the schematic without any values other than voltage
and locations of the parts, labeled with what they are but not even
the sizes of the parts. The funny part of the circuit is that the coils
are even more unique than a finger print, so, when folks ask "How
many turns are in my design, it really doesn't matter. The turns are
only responsible for the voltage per turn on the primary and the
secondary. What other builders don't realize is the fact that the
length of the coil, the spacing between the turns, and the diameter
are all part of the outcome that gives us the inductance of the coil.
The inductance is an important factor that gives us resonance at a
specific frequency when a capacitor is added to the coil in series or
parallel. A capacitor and an inductor creates a tank circuit . The tank
circuit will resonate at whatever frequency it is built for, however,
the capacitance and inductance of the tank circuit are the prime
reason why the tank circuit oscillates at the frequency it's
designed for.Factors in other components of the circuit, such as
coil capacitances and other inductances will change the desired
results, so, all parts of the circuit that connect together must be
tested for their total inductance before and after they are
connected together, then, capacitances of each part of the system
before and after their connections are made to see whether or not
they rise or drop, then, additional components will need to be added
to tune them back where they need to be to find and maintain
resonance.


When people ask what size wire and how many turns are use in say
the "L1" coil, there isn't enough data to build the circuit with this.
The best question to ask would be "how much inductance is in L1,
and, if any, how much capacitance does it have?


The things I did to have a successful resonation is the following:


Find the printed NST frequency. Then, add a gas discharge tube to
the outputs, connecting one of the NST's hot legs to one side of the
arc gap and the other hot leg to the other end of the arc gap. Turn it
on and test the frequency with an oscilloscope and a hv scope probe
that will handle the level of voltage from the NST. This will give the
correct feed frequency. Next, we have to test the NST's
output for capacitance with an LCR meter, and, the inductance.
Then, we need to wind our L1 coil, documenting the L1 coil's
length (precisely) and keep them separated, measuring the
inductance of the L1. Once we have this completed,
we need to connect it to the output of the NST
and test the inductance while connected. Once we obtain this measurement,
we need to take this and go to an online resonance
calculator to see what the capacitor size is that is needed to resonate
at the circuit's drive frequency. We need to add our capacitor to the
circuit and test the capacitance when connected with the cap inline
or in parallel so we could see if the capacitance remains where it
should be. If not, we need to tune it by adding the capacitance
necessary to land at the correct capacitance calculated by the
online calculator. Once this has been done, we need to energize
the circuit and scope it to see if it resonates and the frequency
is exactly where it is tuned.. the desired frequency. If it is off,
capacitance must be added or subtracted to get it correct. Once
done, we need to wind the next coil either 4 times longer or 4
times shorter, so we have a mutual coupling at a quarter
wavelength. This needs to be done from each node, which
will be a termination, a soldered connection, where wire goes
from stranded to solid, and, where the wires end up, such as
a termination on a battery. If the total length from the coil to
it's destination isn't calculated, the self resonance or mutual
coupling of the primary to secondary will NOT happen and the
circuit will fail.''


The secondary side is a little bit tough to do because we need
to calculate the length so we could land at an appropriate turns
ratio. This nearly never happens, however , I had instant resonance
the first try when I weighed out exactly the same wire weight for
the coils, as Tesla states he did. If you do this, the scale needs
to be precise. If we use the same sized wire, the lengths need
to be any even multiple of the other side. It's difficult to do
regardless because the precision has to be within 1/32". That is
difficult to do with wire cutters, so, weight is easier. The primary
could use fine strands such as #34 wire at 1/4 the length of the
secondary, and, the turns ratio is best to have a long enough
length so it has a high resistance, meaning it should have 100 to
500 ohms. This requires a very fine wire and a lot of wire. It also
allows the cold electricity to pass as the hairpin circuit does
with high impedance light bulbs do, while low impedance allows
nothing to pass, especially when in parallel. Resistance is part
of the resonant frequency, so, if Don took the 8 awg wire and
he added a 500 ohm resistor inline with the l1 coil, inside of the
tube, we would never know unless we tested it.


The Hairpin Circuit, researched by Karl Palsness has proven that
high impedances allow more power to pass within the circuit,
and low impedances virtually eliminate the energy transformation
/production. This is KEY with Don's system, and, we could add
the resistance to the resonance calculator to come up with an
LCR circuit that performs even better and is easier to tune than
the LC circuit since the capacitor values will be easier to acquire
if we add resistances. We will also be able to manage frequencies
within our full wave or half wave recitifiers by adding caps and
variable resistors within the bridge. This is key for controlling
frequency along with the use of inline chokes and capacitors
across coils with the use of a resistor.


There are hundreds of variables we need to cover in the Don
circuit, so, if we leave this alone, we will find we will never get
the outcome desired.


The most critical point in the system will be shunt points. To
add a short will need the use of another coil. Look at Don's
schematics. You'll see that 4 of 5 circuits use a short or they
are shunted with capacitors and arc gaps to bring in that
additional energy from the ambient. These systems are very
real.. We need shorts to make it work just like Ishmael Aviso
does. Short them it works!!!

[BroMikey]

Continuing entry on practical design for Don Smith Device.


Marc Belanger 3 hours ago
+Bro Mikey yeah, there are short circuits at the l2 coil, as a few of
the original diagrams have one completely shorted coil as well, it has
a 4th coil to transform the energy. there are shunts using caps as
well because some of the coils don't have resonant caps. the .047uf
cap is a shunting cap, but, we need to look.at the correct diagram.
I.figured this out because of the oscillation caused with the closed
tank l3 which.is in series with l3 and a bridge rectifier.

I've been slowly but surely collecting all parts of the system Don
built... I mean all of them except for the last yellow coil and the
Cornell Dublier caps

(.1uf 4kV wvdc yellow intro caps he had made)

anyway, I found the radio shack inverter, the neon dimmer, and
the barker and Williamson coil. next I'll eventually find the
Bertonee NST, I just put out want ads and wait.. they eventually
pop.up!

this way, when I eventually have it all, nobody can shoot me down
and say I did it wrong. it either works, or it doesn't. there's just
no in between. I've studied this forever and know everything
written about it, plus I have mass experience at failing, so, there's
not many bad ways to.try left.. lol. can't stop.laughing... I burnt
and blew up many things, blasted off screwdriver ends, discharged
caps up to 500 amps, and now since I know exactly what to do,
my ight output design will have to drive enough amperage out
provided the massive 88uF 1200v caps hold up during charge time.

I think they'll withstand microseconds worth of ups, downs and
overplayed, however, I'll have to ensure the load is enough. I
could shunt the circuitry with heaters until I figure out the correct
sized cap for the right voltages and amperage. my calculation was
1200 volts to give me 120 volts continuous. 10 times the over
voltage with minimal amperage to mix with 10 times lower voltage
and 10 times the amperage for a very substantial output.
supposedly, the frequency and oscillation between the output
coils and the short produces the Casimir effect according
to Don.

[sinergicus]

scope trace at resonance

How should look the scope trace when primary are in resonance
with secondary?

Can somebody post some pictures?

[BroMikey]

How should look the scope trace when primary are in resonance
with secondary?

Can somebody post some pictures?

Hello Sinergicus

Not sure if the Don Smith device always shows proper volts
or amps and that would also effect a scope shot. I believe
that this anomaly is stated often with the Don S. but maybe
someone else will correct me.

[med.3012]

Hello Sinergicus

Not sure if the Don Smith device always shows proper volts
or amps and that would also effect a scope shot. I believe
that this anomaly is stated often with the Don S. but maybe
someone else will correct me.

i agree with you Bro, in my opinion this look like digital versus analogy systems, in the latest test using an extended bifilar arrangement the voltage is radiant but accompanied with ordinary electric current so the final power is real active, it's no cold anymore after using it from the capacitor banks, the system work in more dimensions , so it's no easy to catch it !