Donald Smith Devices too good to be true

[janost]

Got the 5.6uF cap to work but it takes to long to charge.

Tested with a 150nF cap and it charges in every cycle.

Now it fires a 16.6Amp pulse, 2uS wide, every 10mS into the battery.
That's only 3.3mA continously.

Not good enough.

[clarence]

I think he might be referring to this device with the big variac and big custom made transformer, which is mounted in an industrial style equipment rack:

Hello Level,

clarence,

Thank you Sir, I appreciate that info and your efforts sincerely!
mike,onward!

[janost]

Got the 5.6uF cap to work but it takes to long to charge.

Tested with a 150nF cap and it charges in every cycle.

Now it fires a 16.6Amp pulse, 2uS wide, every 10mS into the battery.
That's only 3.3mA continously.

Not good enough.

Say I put a resistor (god forbid ) in series of 1Kohm?

5.6uF x 1000ohm = 5.6mS dischargetime.
146v / 1000ohm = 146mA dischargecurrent.

Would it work?
Or do I just lose the 146mA as heat in the resistor?

[Kokomoj0]

Do I have time to read 289 pages on this topic?
No of course not, who does.

So is Donald Smith too good to be true or not?

Why do these alternative energy threads essentially go nowhere?
They all start off sincere and then they lose their focus and vision?

selah V

ox

Its a hoax, I said so in the very beginning but like the TPU get drowned out by the dreamers.

You need not go beyond the slick willy presentation if you know what to look for.

I hate to see people waste their time like that.

If I were to get involved I would lean toward things naudin got to work, at least he appears to have real knowledge and does not send up huge red flags as these others do.

cheers and happy winding.

[Kokomoj0]

Got the 5.6uF cap to work but it takes to long to charge.

Tested with a 150nF cap and it charges in every cycle.

Now it fires a 16.6Amp pulse, 2uS wide, every 10mS into the battery.
That's only 3.3mA continously.

Not good enough.

never forget that step. I tried bringing that up in the dollard thread and again was drowned out. It will save you much wasted time.

[janost]

never forget that step. I tried bringing that up in the dollard thread and again was drowned out. It will save you much wasted time.

I have never claimed anything different.

And I measure across a 0.3ohm resistor in series with the battery, and the scope shows current in and out without lies

[janost]

My HV-feedback killed the IRFP-450

I removed the feedback and changed the mosfet to an IRFP-460.

The current draw is now 32mA and the mosfet can run without a heatsink

The 150nF cap on the secondary charges to 205v.

[hotrod68r]

hey janost,have you tried a voltage doubler on the secondary.2diodes 2 caps.

[janost]

hey janost,have you tried a voltage doubler on the secondary.2diodes 2 caps.

Not on this but sure, it would work.

The thing with a voltagedoubler is that for every stage, it doubles the number of cycles required to charge to the maximum voltage.

It takes twice as long to charge.

[Gedfire]

Clarence: Tower Device

Hi everyone!

Hello Clarence,

The device I refered to as the tower device has two versions.A three section and a two section.

Look at the pics in this post to spot the other one.

Ged

[clarence]

tower info

Hello Gedfire,

clarence,

Thanks much Gedfire, I did distinguish the two as you said. Thanks again for your consideration and efforts Sir!!!

[Gedfire]

Clarence Soundiceuk

You are welcome Clarence

Soundiceuk, I have set up a dropbox.

Ged

Hello Gedfire,

clarence,

Thanks much Gedfire, I did distinguish the two as you said. Thanks again for your consideration and efforts Sir!!!

[Gedfire]

Pulsing High Frequency To Capacitor

Hi,

Pulsing HV Capacitor with different frequency
Don Smith Table Top Device Part 4 - YouTube

CORNELL DUBILIER - 940C30S1K-F
http://www.cde.com/catalogs/940C.pdf

can anyone explain this?

Hi,

thank you very much for the video link! Gave one of th answers I was looking for for so long.


Let me try to explain the way I understand it.The capacitor was been pulsed using a function generator at a low frequency.No light was seen from the 100hz square wave.No light was seen in the bulb.Note fucntion generator voltages are very low.


Now when the frequency was raised to 100khz the bulb did light up @ the same voltage.This fulfils what Don siad about the formula

E=0.5xCxV squared x frequency.

In other words, high frequency means greater power stored in the capacitor.

Based on the voltages seen in the video, I concluded that the AMPS went up significantly at high frequency.Thus more power to light the bulb.

Light emmiter could be a neon too.Don't know.

If you need further clarification, please let us know.

Ged

[hotrod68r]

Untitled Document

like this janost.only 1 stage.i tried it(no load)and had 1/3 total v on c1 and 2/3 tv on c2.your right,you pay for the bemf charging c1 but it adds to the hv output so see what happens.i'm messing around with a ferrite rod with 4 layers,2 for power,2 for feedback now.1 aaa batt.voltage takes ages to drop at 10-15khz,.001 res on meter.uses a little bit at 1-3 khz.also when its going the coil feels somewhat alive with tiny tremors and tiny static tingles.apologies to the hard core here for talking about flea power.

[janost]

Untitled Document

like this janost.only 1 stage.i tried it(no load)and had 1/3 total v on c1 and 2/3 tv on c2.your right,you pay for the bemf charging c1 but it adds to the hv output so see what happens.i'm messing around with a ferrite rod with 4 layers,2 for power,2 for feedback now.1 aaa batt.voltage takes ages to drop at 10-15khz,.001 res on meter.uses a little bit at 1-3 khz.also when its going the coil feels somewhat alive with tiny tremors and tiny static tingles.apologies to the hard core here for talking about flea power.

Its not flee power.
It kills bugs in those racket type bugzappers