Free Energy Device Working - COP ∞ - Please Replicate This

[sinergicus]

I,also have a copy of this motor. I have built one in linear form, and it does work. The theory is sound.I have not built one in circular motion. It usually takes a different approach to make a magnetic motor run in a circular motion. I am sure I know how to do this, but it would require several sets of magnets for the stator and two magnets for the rotor. They would need to be offset so only one set is engaged at one time. This way while one set is pulling, the other set is coasting. I have made a CAD design I am going to try as soon as I get the time and materials. I have the book, but not in electronic format, sorry. Good Luck. Stealth

Great;this means, that principle is not a scam.
If you have achieved to building a working linear model,you know how the polarities the magnets must be, so
please let me know how are they polarized because I have difficulties to understand this from that pdf plans (my english is not so good).

1.So the magnets are polarized on thickness or on width ?
2.You are used steel blockers to diminished the magnetic field (How they recommended in that plans?)


thanks

[Stealth]

Yes, magnets are polarized through thickness. One side north, one side south. The steel helps negate the field as it approches the magnets. When properly spaced, the magnets will pull through this arrangement quite easily. The last three magnets need to be spaced farther away. You can do this either of two ways, either set up like he has it with magnets deeper into the base, or swing away from the straight line, as in a butterfly pattern. I prefer the butterfly pattern myself. I have built countless linear magnetic motors and have had success with most of them. Building a circular magnetic motor however requires a different approach. Mattew Jones has the correct approach for linear motors, with a two non magnetic chains rolling around four cogs, with magnets in the center would be about ideal. Although he used belts,chains have less friction than belts. This would constitute a continuous magnetic motor. If you do build one and get it working,I will tell you how to increase the power without increasing magnet size. Good Luck. Stealth

[Matthew Jones]

This would constitute a continuous magnetic motor. If you do build one and get it working,I will tell you how to increase the power without increasing magnet size.

Share the wealth brother....Spill the beans.....Tell the world....LOL... I need an increase in power.

Feeling pretty good right now, the Saints Won!!!! Talk about free energy, can hear New Orleans from Virginia...
Matt

[Stealth]

Yea, the Saints won, hoo ray. I do hope you have built a self running magnetic motor. If so, you are ahead of me. I have built several prototypes only to be defeated at the last moment. I however, have learned from my experiments, and now am ready to finally build a self running motor from a linear design, similar to yours. I have, as of yet to secure the parts to build one. If you are using ceramic magnets, as I am, you will need to cut some steel pieces the same size as the magnets pole sides. Steel pieces should be half the magnets thickness. You can stack three magnets together, after that, you can't gain anymore power, no matter how many you stack. Now put the steel piece on the back of these magnets to really increase the power. You can save money by buying low power magnets and by stacking and partially negating the field by using steel plates. When you get this built, I would like to see a video before I tell more. I spent a full year experimenting and documenting magnetic anomalies. I wrote a book from my experiments. Although I haven't published it, it has been a valuable resource for me.Good Luck. Stealth

[sunboy]

Closed circle can work?

.
Closed circle can work?
.

[Stealth]

Try and replicate this design. It will work in continuous operation if proper dimentions are used.Good Luck. Stealth

[Farmhand]

Hi Matthew, I just watched your video of your small track, looks like it works to me. I was wondering if you considered using that setup to kick a pendulum.

Seems to me if you had two tracks out at an arc maybe 60* with both gate's pointed to the center they would act as a brake and a Kicker maybe. I wish i had more time to try all these things. That track looks usefull.

Cheers

Aaron



Even a Halbach Array exerts force in 2 directions at the same time. A full magnet exerts force in 4 directions. Each corner exerts force.
The Halbach is asymmetric but not in the right fashion. It only creates a stronger North or South pole.
Every example Howard Johnson shows in rotary or linear track exerts energy from 2 corners of opposite poles from either the Drive or Driven maget. This is the key. This is how you maintian a spinning motion within the feild. The large corner exerts more than the smaller so in can fire the driven magnet set past the smaller corner. Or the smaller corner is shorted out all together to add to the net force of the larger ones.

I am not saying its not worth trying. I just say I don't see anything in it that shows force applied in rotary closed loop fashion.



I am not understanding the thought train that this is anything close to Howard Johnson's gates. I have built several gates for linear straight motion.
The gates first magnet emulate a hollow magnet. The one corners field rolls into the center. The second set of magnets allows for that field to roll through without being interrupted by a opposite poles field, this is why soft rubber poled magnets can be used.
The whole process is very asymmetrical through the tube. It also gains power from the A fields on the driven magnet.

On the contrary this magnetic assembly shows no asymmetrical behavior. In fact under a model it has very symmetrical fields that present themselves similar to the Halbach array. Except the field reside to the bottom of the assembly. The field is very weak at the top. This is why the author brings up angles. 30 deg. You can turn the DRIVE assembly 30 deg facing to the Right outside (as drawn) and you may get a small incomplete rotary motion. But you will not get a closed loop to roll all the way through.
The author says so as well. "The force disappears..."
I can tell ya why. When you stick magnets together they unite to create one field. When you space them out, as in the the driven example, the still flow through each other. The outer bands of the flux now are very weak and cannot interact with the fields on the drive magnet assembly.
Under an Open loop you will only gain power from the start and end magnet. The rest of the magnets will only allow for the field to flow by, at the same time they will take power from the system and not return it.
When closed there will be no power because the primary amount of the flux will stay withing the path of the magnets. You will have nothing to start the motor with.

Johnson solved the problem within is arrays by creating an interaction between to sets of magnets that would not allow them to stay in a stable field. They fired. The drive magnets and the driven magnets fired at every interaction between the 2. No exceptions. It also gained speed until equilibrium was achieved.

I have a small track that does this. Its not the one in my signature. But I have it posted here.

Now I would like to hear the argument for.

And again I don't want to discourage anyone from trying. I just am sharing my experience.

Matt

[megapat]

Thank you very much!!! It's time to be free from energy needs!!!

[sztudynt]

Can somebody share the books of Joseph H Cater (The Awesome Life Force and The Ultimate Reality) in electronic format?
This will be very appreciated .These books seems to contain interesting and practical information's ....

Anybody still looking for this book?


Because I can give you a link to this publication in electronic format, but only "The Awesome Life Force"

[Guruji]

Magnet motor

Did anyone try that magnet combination mentioned in this thread on first post?
Thanks

[sztudynt]

Link to the video concept in post :


http://www.energeticforum.com/renewa...html#post81220



... doesn't work. Where can i find this video?

[ewizard]

I'd be interested in the book (The Awesome Life Force) if you can share that link or PM it. Thanks

I'd like to see the video also but the link is not working if anyone has it too. It doesn't appear anyone took Dr. Yin's concept very far (unless it worked so well they decided to keep quiet)

[sztudynt]

I'd be interested in the book (The Awesome Life Force) if you can share that link or PM it. Thanks

Here is the link:

zSHARE - The-Awesome-Life-Force-by-Joseph-Cater-OCred.pdf - Free File Hosting Service | Audio and Video Sharing | Image Uploading | Web storage

It doesn't appear anyone took Dr. Yin's concept very far (unless it worked so well they decided to keep quiet)

It seems to be true. I really don't understand why people doesn't want to share with other, telling them the truth. What Jesus said? Read Bible (Mt 25:1-13). John Lenon was singing "all you need is love", it looks like we have everything except this small thing mentioned by John.

What is happening to the world is horrible, people are starving, killing each other. We all have forgotten what our true purpose on this earth. We have to look in our root, because we are from God. Not as though Charles Darwin, then said and after all wrote, "Maybe we evolved from monkeys!" This was only the theory, not real fact. But the real title of his book was: "On the Origin of Species by Means of Natural Selection, or the Preservation of Favoured Races in the Struggle for Life"

Wake up people, only with love we can build something on this earth.

POWER WITHOUT LOVE LEADS ONLY TO CATASTROPHE!


PS. sorry for my english, still learning.

[Iotayodi]

The video has been removed.

There was one interesting Mylow video I saw where he held up some magnetic viewing film and showed a magnetic wave when the magnets went by the film.

I had observed that too. Looked like a sine wave.

[ewizard]

sztudynt, Thanks very much for the link to this book. It looks excellent. The author's name sound familiar.
You are doing very well with your English. I understand everything you wrote.