my smith kanapadz replication

[EMCSQ]

Hi Juju and all,

To replicate the Kagagen version done by Romerouk:

- the winding direction (woopy B )



Shows the winding directions: CCW - CW- CCW



Note: This schematic shows overall circuit layout with approx. tube coil dim.

The Ground rod connections need to be at least 10 meters apart. The further apart, the more energy gain.

- turns number of each coil (see diagram) with wire diameter 4mm stranded except the big coil = 10mm stranded.

- PVC tubing 5.5cm dia. X 40cm length X 5mm thick.

- 3 videos of how it works

YouTube - Kapanadze replication v1.1 - Kapagen coil Jean-Louis Naudin

YouTube - Kapanadze replication v1.2 - Kapagen coil Jean-Louis Naudin

YouTube - Kapanadze replication v1.0 - Kapagen coil Jean-Louis Naudin

- a lot of explanations about the MOt without or with diode and cap to rectify the current.

Selfrunning Free Energy devices up to 5 KW from Tariel Kapanadze







Romer so far shows in his latest videos 900 watts output for 250 watts input.

This is very similar to Jean Louis Naudin's design.

Regards, Mike R.

Due to my investigation Windings like shown in alternative B makes sense.
The middle wire in the coil is a must. Those who are familiar with this subject should respond.

[dragon]

Hello dragon,

I have investigated the effect that toubles you. The common light bulbs will work at HF currents as far they work on low potential. If they go above a certain potential, the fillament will produce a blue flame and eventually not light at all as a bulb near a Tesla coil.

This i have found replicating Tesla's electrical conversion and distribution patent.

The easier thing you can do to alleviate this problem is to diminish spark-gap voltage breakdown. Instead of 2-3 KV go to 1Kv.
If then your capacitance fires a lot or the gap is bridged then increase capacitance and keep voltage low same time. This will boost current and keep voltage to suitable levels for lamp use.

Hello baroutologos, I'd really like to shut down the HV on the output and improve the amperage. I have no real use for "lighting bulbs", for realworld use heat and energy storage is useful. Lighting really isn't a problem. Below shows a unit I put together about 2 years ago, primarily for driving a resistive load. Designed to drive a resistive heating load, works with any resistive load. It has 5 - 100 watt bulbs and 1 500 watt halogen... all the lights I had to get the resistance close to where I needed it. My camera compensates for the lighting but they are indeed all at full bright and producing lots of heat. The input for that set up ( 14 ohms all in parallel ) is 618 watts. That unit is designed for a 10 ohm load and will run a 1200-1500 watt heater at or around 500 watts. Only 2 components, no spark gap or HV.

I run my house from wind and solar so efficiency is the primary goal although it would be nice to find another reasonable "alternate" source for battery charging. Winters are brutal for energy demand.

Everyone seems to be pushing toward driving the bulbs with brute force on the Kapanadze replication using the MOT's, I chose a low output NST to try to find the reason it appears to work without input/or a very low input requirement. Results are easier to see if you've made any gains on output if you only have a certain input to work with. I modeled the coil around tesla's patent with an added reversed transformer effect... the second picture showing the tesla patent. This works reasonably well to convert the HV into amperage on the waste side but still the voltage is higher than I'd like to see. Anything below 2000 volts from the NST seems is difficult to keep a spark gap steady. My adjustable spark gap is set up with Tungsten steel tips which has helped considerably in altering output and making changes on the fly.

I'd like to try an experiment posted by Armegdn03 (video) a page ago or so that actually looks promising in creating the elastic bubble or bounce we seem to be looking for as well as a possible clue into what exactly is in the center of the kapanadze coil. Possibly an adjustable cap to compensate for the earth ground capacitance and regulate frequencies into and out of the ground. There is still some confusion on the earth connections as to what is gained by them.

Experimenting and building is fun in any case and usually leads to other ideas....
________

[ewizard]

dragon, Can you elaborate or show the circuit you are using to get a heater type load to work from you ~600 watts input? I also am trying to keep winter heating affordable and I'm very interested in anything that can help toward that. I've got a 12 KV 'Franceformer' brand NST I'm thinking about trying with the TK device and would be interested in any experience you've had with hooking that up also for this setup. I've been following the OU thread also and see bolt had some good thoughts on how to use an NST for this.

[dragon]

dragon, Can you elaborate or show the circuit you are using to get a heater type load to work from you ~600 watts input? I also am trying to keep winter heating affordable and I'm very interested in anything that can help toward that. I've got a 12 KV 'Franceformer' brand NST I'm thinking about trying with the TK device and would be interested in any experience you've had with hooking that up also for this setup. I've been following the OU thread also and see bolt had some good thoughts on how to use an NST for this.

ewizard, it's just a basic series LCR adjusting the resonance to 60 hz. I used a MOT(primary only) which had an inductance of 49mh, a motor run cap of 96uf with a 10 ohm load.

I've run it with several wire wound heaters all work well producing the same output temp as it would normally plugged in. I also tried some newer baseboard heaters with a resistive core type element and it didn't work as well with those. They work with a little decrease in output temp but the MOT runs warmer than I'd like. It seems fine with the wire wound units.. not sure what the difference is between them. 1200-1500 watt units work well with the above components.

It alters the internal frequency and will not run induction motors properly so if you have something with a fan in it the fan will have to run on an external 60hz source.

Be sure to insulate the output of the secondary( not used ), it will still generate very high voltages in it. Any transformer with a primary of around the same inductance rated for the power of the heater or slightly higher will work. Discount Electronic Components ? Tedss.com is a good source for the motor run caps in any size...
________

[vrand]

Hello baroutologos, I'd really like to shut down the HV on the output and improve the amperage. I have no real use for "lighting bulbs", for realworld use heat and energy storage is useful.

The Kapagen is powering incandescent light bulbs that has a small lighting heating resistor element. It should be be able to be used to power an electric heater as well.

Jean Louis COP of 8 is showing something special is happening with the Kapagen design. There are several others also reproducing the Kapagen with success.

I know of no other FE device that an independent researcher has replicated that puts out 100's to 1000's of watts of power.

Even when our own Tutanka shows how he powers his engine on his special gas mix, that still has not been verified by a 3rd party reproduction. Another member Eric Dollard also have not explained how he powers his radios on his FE device, so that others could try to reproduce and verify that it works.

The key here is that this is the first time a FE device has been independently reproduced that these power levels. This is getting close to being able to power our homes (at least our light needs).

Regards, Mike

[The_italian]

Do you now what is factor of power ?

It is called also "cos φ".

Power factor - Wikipedia, the free encyclopedia

it is wrong to measure current and then multiply voltage current.

[cosmo-lv]

Kapanadze device is based on one wire electricity and the coil outside the green Tariel`s device is real transformer who transforms two processes into one.

Coil alone not working and newer works - without some specific processes.!

[broli]

Kapanadze device is based on one wire electricity and the coil outside the green Tariel`s device is real transformer who transforms two processes into one.

Coil alone not working and newer works - without some specific processes.!

Can someone ban this troll please.

[boguslaw]

Can someone ban this troll please.

Why ? IMHO He is saying with sense.

[broli]

He's playing mind games. People are building and making good progress and he keeps nudging them "you're doing it wrong", with his sage knowledge without ever being specific or contributing in a constructive way. These "I know the secret but you need to solve my puzzle" are as worse as the arm chair skeptics or disinfo agents in my book. We do not have time to play these games. I don't know how many years this forum has been up, people like him have come and gone without contributing anything besides getting their 5 min of fame. They are useless and need to be weeded out to avoid distractions.

[baroutologos]

@ Cosmo,

Everyone here is fed up with theorizers claiming to know all.
It seems to me that you speak with OU confidence.

Show your setup, meters, state efficiency claims and principle of operation and then we investigate your views.

Otherwise, please go play to another kindergarden

[dllabarre]

@cosmo

Please answer my PM I sent the other day.

Thanks,

[cosmo-lv]

broli - Thank You!

dllabarre - take a look on answer

P.S. i only thalk with them who want to cnow - and want to build and experiment and do something, but i`m not talking with theses who saying i`m playing games.

this is not game! i`m not here to playing games!

[EMCSQ]

@cosmo-lv

It would be nice, if you would answer my PM too.

[dragon]

other experiments

If a post doesn't seem to offer any real insight to solving a problem then simply ignore it, if it does then apply it. There is no reason to clutter up a good thread with complaints or verbal pissing wars.

Getting back on topic here is a simple experiment that I had done several months ago using a small NST, spark gap and 15 watt bulb. I wrapped a dozen or so winds of heavy speaker wire around a well pipe and drove the load with a single output lead of the NST. It worked quite well... the NST was one from allelectronics ( 2000v 10ma 12 volt unit $6.50). It would light the 15 watt 120v bulb to near full bright with an input of around 400ma at 12.5 volts. The spark gap wasn't real stable but it was enough to inspire me to continue on. Below is a diagram of the experiment
________