my smith kanapadz replication

[tianboon]

Donald L. Smith

I have started a new thread exclusively for discussion on the SR 193 Device. The thread is entitled SR 193 / SR193 - Study of the Device, Theories, Diagrams, Schematics & Experiments

Is there anybody working on the Donald L. Smith "briefcase" device?, I build one but did not get power at the output, perhaps I need a ferromagnetic rod through the center of the coil? like what it said on the SR193 video?

[vidbid]

Smith / SR193

Is there anybody working on the Donald L. Smith "briefcase" device?, I build one but did not get power at the output, perhaps I need a ferromagnetic rod through the center of the coil? like what it said on the SR193 video?

I wasn't aware that details had been released on Smith's briefcase device. Could you post a link to that information?

My impression is Smith's idea is accelerate and increase energy levels. Everything he does is to increase the voltage.

[tianboon]

Don L. Smith

Here is the link:

Freeenergyinventions

[Joit]

tianboon
I can give you my Guesses, but without guarantee. Would be helpfull, to see your device.
What i can see at the Link, he did not use a Core, so it works for him without. Cores may create disturbance at Resonance or act different, at the other side, they increase the Power what can be produced with a Coil. I would try to use frequency above or around 20 khz. Also the Resistors and Capacitors should match to the Coils. You can adjust that over higher or lower resistors, or the Capacitor, but he must be in the range of the Frequency at his discharge rate. Also may try to use a spark Gap, and a different Duty cycle, where you create the HV Pulses.

[tianboon]

Don L. Smith replication

Thanks Joit for your advice, I am not too sure how to send a picture on this forum yet.
My system I build was base on Don Smith's schematic, but slightly different, I am using FB transformer powered with one single transistor instead of a NeonST, and my capacitors value are different than his, the wire gauge on the Tesla coil more likely differ than his, but I am able to tune both resonance the primary and the secondary close to 1 Khz, primary resonant was 134.31Khz and my secondary was 135.67Khz. it is hard to get 100% exact freq. on both side.

I adjusted the SG the best I could within 1mm, but the output voltage at the bridge rectifier fluctuates, my SG gave noise and not silent like Naudin's or SR193 SG, perhaps you can give some suggestions how to make the SG silence with a nice blue stream, another thing is when I removed the earth ground from the bridge, the voltage drop quiet a bit.

I haven't got the chance yet to test it with an inverter , not too sure if I got enough amperage, I rewind the secondary coil, the first half is CW and the second half after the center tap to CCW, hopefully I will get some current, I will try and test it again tomorrow..

[Joit]

Picture upload

I still read through Don Smith pdf few times, to find more about, what he did do.

You can do that by clicking the Image button with the Rock on it at the Menu from the Reply Window.
First, Save a Picture what you want to upload as jpg in a small Format, that it dont use much Space.
Artweaver is a Free Program where you can do that.
At the Popup Window choose Search, locate your Picture and then click upload at the Popup.
Then you did attach it to your Reply.

Other Function at the Reply menu, mark text at your Reply and click the Insert Link Button, to make a link to an other Page.
it shows up when you move your mouse over the little Items above there.

[Joit]

More from Don Smith at 3-25. At 3-50 are the Tables to calculate the Capacitor and the Resistors again.
http://www.free-energy-info.com/Chapter3.pdf

[tianboon]

Don L. Smith replication

Thanks Joit, this is a good find, I must have missed this one, going back to his circuit, if you look at his schematic on his MMC before the bridge, he has 2uF, 8000 V on his MMC, I am wondering if you know of hand just by looking at his schematic, does the value of this MMC critical?, I borrowed my nephew's MMC which has 0.1 uF.

On page 3-25 info, I think what he meant was the Primary coil winding ought to be CCW and the Secondary coil should be CW? what do you think?.

On page 3-50 info to measure the reactance, I am not too sure if I can measure my FB's frequency without damaging my meter, any suggestions?

[Joit]

Can you tell me, wich Circuit you refer too? But i think the most capacitance are critical at his builds. A Capacitor charges at decharges at certain Cicles, depends on his Size. It has Influence into the System. I found a Page about homemade adjustable Capacitors from .002-10µf, and would not wonder, if they do work for HV too withouth getting damaged.. Baking Soda or Borax, Water and 2 Aluminium Strips and you got a AC Capacitor without need to buy it for couple hundret Bucks. For measuring the Frequency at HV i would be careful too, maybe first with an old Meter, that can be damaged, but else i think, HV can damage a Meter any time, maybe it works over a Shunt resistor.

[tianboon]

The complete circuits for 12 V NST's

I am sorry, didn't mean to confuse you, if you click on the link "freeenergyinventions" on post number 5 and scroll down until the page says "The complete circuit for 12 V NST's".

I tried copy and paste, it did not work on this reply format

[Guruji]

Eager to build one

Hi guys I am eager to build like this system but once I read that spark gaps release X rays. I asked this many times but no one answers don't know why.
Anyone heard about this?

[vidbid]

X-ray A Spark Gap

Hi guys I am eager to build like this system but once I read that spark gaps release X rays. I asked this many times but no one answers don't know why.
Anyone heard about this?

If that's true, then wouldn't spark plugs in automotive engines be emitting x-rays too?

Maybe we should put lead shielding in automotive firewalls.

[Guruji]

Spark

If that's true, then wouldn't spark plugs in automotive engines be emitting x-rays too?

Maybe we should put lead shielding in automotive firewalls.

You're right vidbid very true
Thanks

[tianboon]

Need pick some one else's brain

I need to pick some one else's brain

I have inserted two ground rods about 10 meter apart, when I put a volt meter between these two ground rods, rod A and rod B, I got a reading about 190 millivolt and when I put an AM meter across this gnd rods, I am reading about 10 micro amps, can anybody explain to me what am I reading? nothing else is connected to it, except on rod B, it is connected with a 10 gauge cable back to my VOM, perhaps I am reading Radio Frequencies of the air from that cable?, I live in the rural area, with only one TV channel.

My second question is about oil filled capacitors, normally found inside a microwave oven, what other function or use are they good for? is it wise for me to use this in my HV Kapanadze or Don Smith's circuit?and are they the same as pulse capacitors?

My Don Smith's replication at the output is in the milli amp, trying to figure out how to increase this current

[Joit]

Sorry for delay Tianboon.
I think the Voltage at the Caps there are critical, but Don Smith connected also 2 x 4000V Caps in Serie there. Just not sure about the Capacitance, since it only collects what the Coil spits out and forward it to the Rectifier. Could be, it need to be in the same charge rate as the Frequency there.

For that Capacitors from the microwaves, they have from the manufacturing an internal ERsistance between the Poles, they are usual at the HV Coil, the Resistor is for safety to eleminate Sparks, not sure if the Resistor is at any Caps there, but at the one from Samsung they should be anywhere.

What you do measure there is a Potential at the Earth, we have a Thread here about it where some did do a few Experiments, and when you align them to N-S you even get more out there.

I am still quite not sure about, how to arrange the Coils, but as far i did look at this Device, he has anyhow 3 Coils there, when even i count 4, what should be needed. 1 over the whole Lenght what has a Pickup in the middle and is divided. 2 Coils, where one is at the left End from one Pickup, the other is at the right end from the 2nd Pickup. Anyhow i do miss the HV Coil with thin Wire, what are at his descriptions. But maybe you need tune your Coils to eachother better, that the magentic Field can be better interact.
But for the Capacitors, i think i try a Glass Water with Backing Soda, 2 Alloy Strips, where one is a Triangle, to adjust it, and it should be enough for 8kv.
I hope to save at this Way to look for such Big One. They can be usualy found at Railway Junk.


For the x-rays at a Spark Gap i am not sure about all this Storys, there are x-rays anyway from space, and i think more they are dangerous when they are concentrated like a Gun, but lesser from only Spark Gaps.