Don Smith A review...

[AetherScientist]

I have obtained this picture from another website, but it explains the same thing as Don Smith. The higher the frequency, the less electrons travels in the wire. In HF electrons travels AROUND the wire. So no Ohm's law applies.
Ohm's law can apply on high frequency if the system is not in resonance.



High frequency + Resonance = Zero impedance = No ohmic losses.

[AetherScientist]

[AetherScientist]

[AetherScientist]

Dc and AC skin effect

[AetherScientist]

[med.3012]

It depends on a lot of different things, one thing is the thing you say.

Smith explains that when using resonance in AC there is not impedance (resistance), so there is superconductivity at ambient temperature. When there is not impedance, Ohm's law doesn't apply.

High frequency I think is more important than high voltage because while using HF the electricity travels around the wire, so there is not wire resistance, the second factor to avoid resistance is that impedance = 0 (no resistance). So in this case of superconductivity there is not a random bouncing of electrons (dissipation). Also, instead of linear scale (resistive case), it's applied a logarithmic scale (superconductivity).

Good points, now let me quote from http://www.free-energy-info.com/Smith.pdf :




it's clear there's a replication process by the inductive process... this mean we have to achieve an electromagnetic feedback inside this device, now volt and ampere are equal in a very special physical state, his device work on the same principle as the famous equation of energy :



the above equation is achieved if we could divide the atom for example ( the case of atomic bomb ), in Don device it's very safe and clean to divide the electricity into two portion, magnetism ( amperage ) and electricity ( voltage ) using electron spin mechanism, this is only possible if we could treat the electricity as a single entity, let's quote again from Donald Smith PDF :




when our system meet this condition it will resonate depending on electron spin rotation ... in other words the coil and capacitor will turn into energetic elements, as Don stated in the first quoted text Volt and ampere are equal this is your parallel L/C circuit but when the time come to harvest the power they have to meet each other again exactly in the resistance point ..the system must meet this point to continue its oscillation, max current is achieved, Ozone gas is produced in this stage, the voltage will be radiated as a special radiant energy, standing waves is formed since the device will change its energetic shape to form another parallel L/C circuit ..

superconductivity is formed as electrons attraction mechanism ,here it's the job of the induced rotating electric field, i am talking about the extended Tesla Bi-filar coil because it's the solution.. in my opinion we have to think about it ... it's a very beautiful device ..

[med.3012]

just to explain the skin effect in practice look at the following photo ( it's from the internet ) the horizontally rods are for conduct the high voltage power in electric station.. it's empty inside just to form a large surface and force the electrons to flow outside.. this is necessarily in 50HZ !! imagine in radio frequency speed, it's clear we have to use a large surface ..

[AetherScientist]

Don Smith, as you said, explains that volts and amperes are the same. The only difference between them is the direction of rotation. One of them rotate CW and the other CCW but they are spin's rotations.

An easy way to understand Smith's work and to know that there are free electrons in the ambient, is to check this device that he built:



The receivers can obtain energy from the ambient agitation that L2 caused. The receivers (L3, L4...) do not deplenish the source because they are obtaining the energy from the ambient.

[AetherScientist]

med.3012

The other day I built a Smith's verion of one of his circuits using electrostatic induction (1 wire induction using plates as a emitter and receiver) and you can see that it's possible to charge capacitors with energy from the ambient.

I put in between the emitter and the receiver an insulator and the second plate (receiver) was receiving energy and it was the same strength as the emitter.

[AetherScientist]

A representation about the circuit I made some days ago

[AetherScientist]

just to explain the skin effect in practice look at the following photo ( it's from the internet ) the horizontally rods are for conduct the high voltage power in electric station.. it's empty inside just to form a large surface and force the electrons to flow outside.. this is necessarily in 50HZ !! imagine in radio frequency speed, it's clear we have to use a large surface ..

And why they use an empty conductor at 50 hertz? To avoid losses?

[med.3012]

Don Smith used a signs.. he never used a direct words that can be explained directly, he never allowed to do this ... ( for contract obligation ), you know ..

in your drawing you are replicating the source power, if you use 10W as initial power you will have 10W in the receiving plate, this mean electrostatic induction have to be used..., if you add to this a resonating device combine the capacitor and the coil the two as the same device, keep in mind there's a feedback inside this device what you achieve finally is something amazing, you are able to replicate this source power 10 W for example with radio frequency speed say 1000 time more power !

[med.3012]

And why they use an empty conductor at 50 hertz? To avoid losses?

Yes they use empty rods in high voltage power station to force the electrons to flow in the surface, if it's filled inside they will meet significant losses, even in high voltage power transmission they use twisted cable for the same purpose

[AetherScientist]

Yes they use empty rods in high voltage power station to force the electrons to flow in the surface, if it's filled inside they will meet significant losses, even in high voltage power transmission they use twisted cable for the same purpose

thanks for the explanation

[AetherScientist]

Don Smith used a signs.. he never used a direct words that can be explained directly, he never allowed to do this ... ( for contract obligation ), you know ..

in your drawing you are replicating the source power, if you use 10W as initial power you will have 10W in the receiving plate, this mean electrostatic induction have to be used..., if you add to this a resonating device combine the capacitor and the coil the two as the same device, keep in mind there's a feedback inside this device what you achieve finally is something amazing, you are able to replicate this source power 10 W for example with radio frequency speed say 1000 time more power !

I know...

Well, I am replicating a Smith's circuit that he shown several times in his videos. I use a car ignition coil and I pulse the input with a PWM circuit DC. Then the single wire comes from the ignition coil's HV HF output.

In my configuration it is like a 1:1 transformer. The question now is...
How can I achieve, for example, 1:2 transformer using the same technique?