Don Smith A review...

[med.3012]

Med,

When the device is driving that light bulb, do you have a guass meter to see if the magnetism has started to permeate through your surroundings?

Thanks!

in fact i don't have a Gauss meter, in the case of toroid arrangement the electromagnetic flux outside your device is almost zero ! this is a good reason to use it so the interference is very low.


i am still doing other experiments by increasing the number of turn in L1, the power increased further more because the condition of oscillation is preferable now, more inductance is better in other hand it's good choice to decrease the width of used foils.

[ilandtan]

in fact i don't have a Gauss meter, in the case of toroid arrangement the electromagnetic flux outside your device is almost zero ! this is a good reason to use it so the interference is very low.


i am still doing other experiments by increasing the number of turn in L1, the power increased further more because the condition of oscillation is preferable now, more inductance is better in other hand it's good choice to decrease the width of used foils.

Med, is your input frequency adjustable? I have noted that DS was trying to re-tune while one of his devices seemed to have output issues. Also the reason I mentioned the Gauss meter is that I have seen DS showing that there was a detectable EM field around his device. This was my point before that I think when we engineer coils, we always seem to worry about coupling of coils where we may need to tune at a different frequency for magnetic resonance. Does that make sense at all, or is that me just being crazy?

Please look at this when you have the time. It seems two opposing wound coils around a POE (I'm not sure that matters) electrically it seems close to what you are doing. Note his magnetic field.

[VIDEO]https://www.youtube.com/watch?v=q_OqvcdXIgw[/VIDEO]

[med.3012]

Med, is your input frequency adjustable? I have noted that DS was trying to re-tune while one of his devices seemed to have output issues. Also the reason I mentioned the Gauss meter is that I have seen DS showing that there was a detectable EM field around his device. This was my point before that I think when we engineer coils, we always seem to worry about coupling of coils where we may need to tune at a different frequency for magnetic resonance. Does that make sense at all, or is that me just being crazy?

Please look at this when you have the time. It seems two opposing wound coils around a POE (I'm not sure that matters) electrically it seems close to what you are doing. Note his magnetic field.

[VIDEO]https://www.youtube.com/watch?v=q_OqvcdXIgw[/VIDEO]

Hello,

at the moment the input frequency isn't adjustable, i am just using a one transistor oscillating flyback transformer, i have NE555 oscillator built by me but it's not stable ( some frequency drop), in other hand we have to be sure about the output frequency generated in the high voltage legs, here DS used a high voltage, high frequency generator to tune his device to the optimal values, after that making the correction will be easy, Mazilli driver seem to be the best high voltage power source, but High power MOSFET are rare around the area where i am now, i already lost one MOSFET, so i need another one to make another Mazzili driver



yes the Gauss meter was used by DS to mention the presence of electromagnetic flux in the space around his plasma globe used in that video, the E-TBC can benefit from this flux because we already use conducting foils instead of normal wires, this mean your device is able to work in more dimensions than ordinary coil !
a friend asked me this :

What is really the "secret " of the device to obtain the extra energy ?


the secret of this device is it combine both electricity and magnetism in just one device, when you do this both volts and amperes ( mean real useful watts ) can be obtained, so it's not a coil nor a capacitor it's both at the same time but there's a sequence when the device produce magnetism or electricity but both meet each other to produce watts, the operation will be reversed and each side AC OR DB will have an opposite charge because the electrons have to relax and change the spin direction, the symmetry in this geometry make the two side appear to be the same, this help the electrons to interact with the negative energy side easily... the device have to oscillate in increased manner since this is the best, the device is able to attract ambient electrons because we are using foils, finally the high speed make it very small but still powerful and dangerous if not treated with care ...

the idea behind this device is exactly what Nikola Tesla was talking about in 1894 ! it's out-of-date !!! but still brilliant ! don't worry if there's a huge electromagnetic flux around your device or not because this is not what we need, we need our device to see what's around its space in a few words this is the secret, the latest tests i did show the presence of increased oscillation when the number of turn increased in L1,it's all about how strong the magnetic field is so it can bounce to make the device oscillate, a lots of improvement can be done, let's talk about this later !

edit : some words added to make the meaning clear .

[ilandtan]

...increased oscillation when the number of turn increased in L1,it's all about how strong the magnetic field is so it can bounce to make the device oscillate, a lots of improvement can be done, let's talk about this later !

Med let me clearly understand this. L1 is just whole E-TBC (input), of the two E-TBC required in the mixed E-TBC circuit?

[med.3012]

Med let me clearly understand this. L1 is just whole E-TBC (input), of the two E-TBC required in the mixed E-TBC circuit?

the Idea behind the mixed E-TBC came after the problem encountered to extract the power from the E-TBC if the junction CD is open, the mixed E-TBC oscillate at the same frequency exactly as the original coil before you divide it, the scope graph show a phase shift between the two side that form the mixed E-TBC, this mean if one side produce voltage the other side will produce current, the mixed E-TBC isn't stable device this mean the phase shift isn't 90° all the time! but because the frequency is the same this geometry is important to study the E-TBC in general, the test i did using air cored Mixed E-TBC show a superiority in power production compared a single E-TBC, but when moving toward a ferrite toroid inductor the scale move toward single E-TBC, back again the single E-TBC take control !!

this mean there's a lots of thing we don't know about electrons spin behaviour, so i am using just a single E-TBC, the number of turn used for the first time was 8, now i am using about 25 turns, still a lots of reversed engineering work have to be done, the time needed for the capacitor banks to be charged have to be studied, the amount of capacitance plus other critical parameters, finally as you mention before the frequency of high voltage power source is important, i am working on a way to kick the voltage In L1 without the need of high voltage high value capacitance since it's not easy to be secured in a lots of area.

after that how we could use the power from the capacitor banks? or what's the best way and the easy, using the obtained charges to attack the primary of step down transformer is also possible but i am wondering how ?

[med.3012]

@ ilandtan

hello !

what's up there ? did you got your toroid ?

[ilandtan]

@ ilandtan

hello !

what's up there ? did you got your toroid ?

Feb 24th to March 8th... coming from the EAST, it's been shipped, sometimes I feel I could of walked to Taiwan quicker.

[med.3012]

Feb 24th to March 8th... coming from the EAST, it's been shipped, sometimes I feel I could of walked to Taiwan quicker.

don't worry ! just go to some old TV store and look for TV YOKE, in most case they are for free since very few people look for it just chose the biggest one so you could start duplicating this device very soon.

[ilandtan]

Med have you tried just wrapping the E-TBC around a soft iron rod, or magnetorestrictive rod? DS has some devices that have that kind of configuration.

[med.3012]

Med have you tried just wrapping the E-TBC around a soft iron rod, or magnetorestrictive rod? DS has some devices that have that kind of configuration.

no i didn't tried this, but i guess soft iron is a bad choice due to the large eddy current created inside the core, the E-TBC will see these current and the oscillation will be dumped.

[med.3012]

hello everyone ,


what's new? any question ? suggestion ?

[AetherScientist]

hello everyone ,


what's new? any question ? suggestion ?

Hi med.3012

I'm a little bussy so I don't post messages. Sometimes I read your posts. Very interesting.

I am understanding better how DS system works. I have a much better understanding at the moment. There are different effects and techniques that are not usually known by the masses.

Almost all the schematics in the net are wrong, incomplete or both.

To better understand DS you have to replicate one by one simple experiments with the new concepts DS explained. Then adding complexity and combining different concepts together.

[med.3012]

Hi med.3012

I'm a little bussy so I don't post messages. Sometimes I read your posts. Very interesting.

I am understanding better how DS system works. I have a much better understanding at the moment. There are different effects and techniques that are not usually known by the masses.

Almost all the schematics in the net are wrong, incomplete or both.

To better understand DS you have to replicate one by one simple experiments with the new concepts DS explained. Then adding complexity and combining different concepts together.

Hi AetherScientist nice to see you !


without collective work it's not possible to go far in this device, a very few member contribute in the positive direction in this forum, others still remain in the silence, so i am moving to work with a real partners, at the moment some are working with me, only when hand in hand we could fight the technical problem..

it's better to work far from some super members! my email is open to any question or suggestion !


regards

[AetherScientist]

Hi AetherScientist nice to see you !


without collective work it's not possible to go far in this device, a very few member contribute in the positive direction in this forum, others still remain in the silence, so i am moving to work with a real partners, at the moment some are working with me, only when hand in hand we could fight the technical problem..

it's better to work far from some super members! my email is open to any question or suggestion !


regards

Nice to hear from you. I think I understand around 80% of DS device.

Here I don't have any physical partners, so all the people is online only.

I will try, not sure, to post something today in some hours.

[njones308]

Very nice discussion here

I only have a minute to post so I apologize for the short post. I want to join in this adventure with you guys on this replication project. I have built an E-TBC. I will attach a couple pics of my setup and see what you guys think. I am looking forward to working with you guys.