Captret - Perpetual Light with Dead Batteries

[gmeast]

size

Testing the Captret: is this free energy? Part two: YouTube - Testing the Captret: is this free energy? Part two.

Nice LS,

What is size of source Cap? I might have missed in video. Three caps in captret array are what?

Thanks.

Greg

[LaserSaber]

The question "is this free energy" is carried over from my previous video. It's just the question that is driving my research on the Captret at the moment. I will rename the video to cut down on possible confusion.

[LaserSaber]

What is size of source Cap? I might have missed in video. Three caps in captret array are what?

I think the source cap was a 1000uf 100v Capacitor. The others are all less than 300v 400uf. I did the same setup once using only 1000MFD 35VDC caps. Link: 1000µF 35V 20% Axial-Lead Electrolytic Capacitor - RadioShack.com It seemed to work just as well.

[electricity]

Large Captret

You guys need large capacity to see fast result.

No less than 200v - 50000 uf is ideal to charge dead 9v

I have ran my 4 gallon captret and also a 5 gallon captret.

You can light 4 cfls @ full brightness perpetually, pics to follow soon.

[electricity]

source

I think the source cap was a 1000uf 100v Capacitor. The others are all less than 300v 400uf. I did the same setup once using only 1000MFD 35VDC caps. Link: 1000µF 35V 20% Axial-Lead Electrolytic Capacitor - RadioShack.com It seemed to work just as well.

stop over paying, go to taobao.com

[ibpointless2]

You guys need large capacity to see fast result.

No less than 200v - 50000 uf is ideal to charge dead 9v

I have ran my 4 gallon captret and also a 5 gallon captret.

You can light 4 cfls @ full brightness perpetually, pics to follow soon.

I will gladly make your big caps but you need to make a how to video on youtube. The words you wright are not comprehend by what we read. (you think this, but were thinking something else) A how to video will be easier to understand.

[Jbignes5]

Ok...

The question "is this free energy" is carried over from my previous video. It's just the question that is driving my research on the Captret at the moment. I will rename the video to cut down on possible confusion.

Yeah putting the name "Free energy" on anything will net you a lot of grief. As we are finding out. Keep going in your experiments. We will find out a way to utilize this effectively and you are exploring all the avenues to get there. Follow your inner voice and go from there it will lead you to where you want to get.

[ibpointless2]

Here is my results so far with my latest captret circuit.
captret results so far for diff volt batt.jpg

[Guruji]

caps in series and in parallel

I have different caps but no high voltage high capacity caps
Can I do a setup in series and in parallel at the same time to acquire highest voltage and capacity at the same time?
Help appreciated.
Thanks.

[ibpointless2]

I have different caps but no high voltage high capacity caps
Can I do a setup in series and in parallel at the same time to acquire highest voltage and capacity at the same time?
Help appreciated.
Thanks.

I've used caps that have 1uf and some that have a voltage as low as 16 volts. The best thing for you to do is gets some caps online, i use mouser.com.

[Guruji]

caps

I've used caps that have 1uf and some that have a voltage as low as 16 volts. The best thing for you to do is gets some caps online, i use mouser.com.

Thanks Ibpointless for response. At the moment I am trying a 25v 4700uf cap with a 9v battery. Voltage rises to 3.35 and stops. Maybe battery is too weak should try another maybe.

[Jbignes5]

So.. What have we learned?

What I have learned is exactly what Tesla was saying. He says that you don't need current. You only need a way to induce voltage in a conductor then hook each part to a cap to keep the separation between the two potentials.

We know from measurements from our experiments that two plates closely wrapped will give a potential difference between them. This is the splitting of the positive concept. Couple that to a load through caps and walla you have a flow of potential. Once the flow is established nature provides the rest. For every action.... <- You get the point....

So lets take this further now. We know that we need three plates separated by the best dielectric we can get. We know that surface area dictates the force we will get from this. We know this force when used through capacitance will not short out the source and kill the dipole. We know that there is a inductive component that feeds back into the source refueling it.
We know that the load must be high voltage capable and that it should convert it down to get real power from it, most likely coils. I would also suggest we fit in balanced mass antenna's with different surface area to pull in real charges from the environment.

So how does that sound so far?

[rave154]

i rigged up a circuit using a two channel flip flop driven by my function gen

ill draw it out for ya'll..

i was able to get two LED's fully bright ( jesus im starting to sound like Tseung here lol )......... with about 15ma draw from the battery.....BUT....the battery wasnt connnected to the main CAP

the battery (12V ) was driving the flip flop chip......however...they do share a common ground connection.......but DO NOT share a common positive connection....unless of course you include the path through the two mosfets and also the path through the + of cap.....top of cap..and - of cap ( ill draw it out, it will make more sense )

basically the circuit was... mosfet-1 ON ( which connects LED-1 from + of cap through to TOP of cap ( at the same time mosfet two is OFF)..

then....mosfet-1 switchs off.....and mosfet-2 switches ON....which connects LED-2 from TOP of cap through to - of cap......and repeat (controlled by the function gen )


more later......im knackered

[ibpointless2]

So i finally figured out how to make a capacitor.

All you need is 16 ounce pop bottle
water
aluminum foil
salt

fill the bottle with water and add some salt, make sure to shake it up very well.

wrap some aluminum foil around the outside of the bottle

take a strip of aluminum foil and put it in side of the bottle with some sticking out of cap and close the cap with some aluminum foil sticking out. thats your positive and the outside aluminum foil is negative.

then just add voltage.

Its not the best in the world but it is a learning experience.

[ibpointless2]

Here is my simple home made captret.

What you need:

aluminum foil
pop bottle
salt
water

I have it hooked up to a dead 12 volt battery and the outer case (-) to top positive it is whats inside the battery (5.40 volts) but the outer case to captret connection (o) it is little lower (5.37 volts).
Captret Home made simple.jpg