Joule Ringer!

[jaggedE]

Hi guys
I got a jouleringer, Penny-like, working by just my fingers and 2 metals.

Jouleringer powerd by fingers, copper and aluminium - YouTube

maybe it could charge a supercap to power something, just by touching it..

cant see much in your video, could you post your circuit diagram?

[Marcel-o]

Maybe there is to much room light but you can here the radio and off course you can see the multimeter...
The LED isn't that bright, i will soon have beter LED's

this is the circuit: PENNY's circuit diagram.ASF - YouTube
again: it's not mine but it's the best low-power ringer i have seen/replicated.
Works from about 1 micro-amp

[b_rads]

Hi guys
I got a jouleringer, Penny-like, working by just my fingers and 2 metals.

Jouleringer powerd by fingers, copper and aluminium - YouTube

maybe it could charge a supercap to power something, just by touching it..

The Penny circuit is absolutely amazing. Lidmotor also made one called the Steel Wire Pancake Coil that is very comparable as well.
I performed a very similar test a while back.
Power Cell Electrolyte - Lifetime Guarantee - YouTube
Those circuits will almost run themselves -

[Guruji]

Joule thief

Last week I was trying to add a capacitor for resonance to my JT ringer but could not find resonance. Anyone tried to add another winding as Zilano once told?
Thanks

[T-1000]

The Penny circuit is absolutely amazing. Lidmotor also made one called the Steel Wire Pancake Coil that is very comparable as well.
I performed a very similar test a while back.
Power Cell Electrolyte - Lifetime Guarantee - YouTube
Those circuits will almost run themselves -

The human body always have potential difference. So you can charge capacitors up to 1 volt.. When different metals are hold in hand, there is chemical reaction with magnesium and other active metals from human sweat. So that amplifies voltage.

[Jules Tresor]

Excellent find Kooler !! The wire in the sleeve )

I hope his joule ringers are NOT alike this april fool device !!

Seriously Lasersaber's Joule Ringers are so interesting, seems so energy savers.

I hope he will find standard toroid and get the same effect than the large toroid used to light his shade !
Congratulations !

[Harvester]

Hi,

After building a modified version of
http://www.energeticforum.com/renewa...tml#post169957
, charging an old battery looked very promising.

The old 12V car battery was at 10.5V and after charging it for a week at around 12.8V, I had it up to 11.6V (after leaving it disconnected over night)

We have been on holiday for the last 10 days, and now the battery is at 7.4V.
When connecting the charger again, it went up to 12.5V for about 5 sec and then stayed at 11.3V.

Anyone got an idea, on why this could be?
Is the battery too dead?
I want to make sure I get the circuit going properly before hooking up a new battery.

[totoalas]

Hi,

After building a modified version of
http://www.energeticforum.com/renewa...tml#post169957
, charging an old battery looked very promising.

The old 12V car battery was at 10.5V and after charging it for a week at around 12.8V, I had it up to 11.6V (after leaving it disconnected over night)

We have been on holiday for the last 10 days, and now the battery is at 7.4V.
When connecting the charger again, it went up to 12.5V for about 5 sec and then stayed at 11.3V.

Anyone got an idea, on why this could be?
Is the battery too dead?
I want to make sure I get the circuit going properly before hooking up a new battery.

There matbe a dead cell that's bringing down the voltage ... how about flushing your battery using the Alum conversion method maybe it eill revive ur dead cells

[Joit]

I got a similar dead batterie, it did rest on 11.30, one from the numbers what indicate me a dead batterie, but still had full amps.I did draw it down, and it didnt recharge anymore, only to about 4 V. At charging it shows 14 Volts, but later drops down back to 4 Volt. I used this thing a bit for my 3 Batterie setup. But i am carefully at this one, when its at 11.30. Usual each cell has about 2.2-2.4Volt Volts, x 6 Cells is about 14 Volt, when one has a short i come to 11.30 again. So it may means, that the other cells are full charged, just one is not and i should not charge it more.
I guess, that sometimes only the grid from that Plates fall apart and cause the short. I converted it to alum too but not much changes. You can try at least to discharge it with a low load, maybe about 5 watt, and recharge it few times again, that it can come back. Aaron did suggest that once, but i had more success at open it and refill it with destilled Water.

[LaserSaber]

All info here: Super Joule Ringer 2.0 in overdrive! - YouTube
Schematic here: Laser Hacker! Free energy made easy.

[totoalas]

Super Cool Joule Ringer

All info here: Super Joule Ringer 2.0 in overdrive! - YouTube
Schematic here: Laser Hacker! Free energy made easy.

Thanks Lasersaber
Limiting the parts to one is the best with an added bonus on the cheap coil design
Now everybody can replicate with ease with easily available parts

Below is my replication of your first joule ringer

thanks again

totoalas
Super Joule Ringer Amplifier Lighting Station 290112 - YouTube


Super Cool Joule Ringer Part Two - YouTube

[Billxx]

All info here: Super Joule Ringer 2.0 in overdrive! - YouTube
Schematic here: Laser Hacker! Free energy made easy.

Wow, LaserSaber, that circuit looks great! What happens when you ground the ferrite of the new coil? EMF from the new coil? Really interesting circuit.

Thanks for posting this stuff, brings new possibilities.

[xee2]

@ LaserSaber

??? Your video shows making a transformer with 3 windings but your schematic only has a transformer with 2 windings.

[Jules Tresor]

@LaseHacker-LaserSaber

Thanks for this new circuit LaserSaber, it seems that you DID IT AGAIN
I am eager to see how it RINGS on capacitors !!??!!

After that it'll be time to make a ringer circuit with a 555 timer to input some power regularly in the ringing capacitor ... what a potential saving in power !!

As for replicating your mini DIY Joule Ringer, I am not in a country where goldmine-elec-products.com ships, so I am f...
I mean to reproduce with the exact same parts you recommend.
I wanted to make a comparative test with light output/energy used, and make a run time comparison on small button batteries ... to have an idea of how much longer it can run with the Joule Ringer added and to see the light output curve vs time.

Your video, "Light_output_test!_LED_without_Joule_Ringer_VS_LE D_with_Joule_Ringer" was a must, but can't find it on your channel anymore... May be the guys at Panacea should produce such "proof" video and publish them, without any risk for the individual inventor, he staying anonymous !

Anyway you are a very gifted man, showing such impressive circuits, that I wish you could give us MORE !!! ahahahaha sorry for that, you have given us already A LOT !!
May the light of inspiration be strong for you !!
Thanks again LaserSaber !!

[seth]

@ LaserSaber

??? Your video shows making a transformer with 3 windings but your schematic only has a transformer with 2 windings.

Im having exactly the same confusion - on the video it looks like the 2 ends of 1 wire are just left open. Can anyone clarify?

By the way, has anyone tried other wires? Or is the doorbell wire a must?

Thanks for the great work Lasersaber. Looks great, and the video is very clear. Very few components - should be able to get millions of replications and fast.