Possible working principle of Don Smith's device

[Jetijs]

boguslaw, I wouldn't waste my time listening to the user Guntis.
And Guntis, you are not welcomed in this thread, please stop posting on this thread, make your own!

[wayne.ct]

Just for play and fun i like to post some my early experiments.

Hi Guntis,
I am particularly interested in the circuit you posted as a jpg. Have you constructed this? Whether you have or not, do you have any details of the construction of the coils or transformers?
Thanks,
Wayne

[Farmhand]

Hi all, Jetijs, I think I was wrong about how I thought the coils were wound and I can see that the picture does indeed look like the original Don Smith device.

Anyway I wound some coils on a tube and made a small primary on a stick to go inside. The secondary is center tapped, I used 4 times the length of the primary coil wire in each half of the secondary, the other coil to the right was for fun. There are 5 turns on the primary and 15 on each secondary. I have pic's attached. They are only small and rough. But Maybe I can find out something with them + 20 000 volt's .

I'm going to wind another identical Center tapped coil in between the two that are on there already. To see if it can output something. The primary can slide all the way from one end to the other.

There is a coil in the PGTFE PDF that is wound the way I descibed in my earlier post. I'm sorry if I caused any confusion.

Anyway I don't have any HV caps or an accurate spark gap yet anyway for these experiments. So good luck with your's.

Cheers

[Farmhand]

Mot

Hi jetijs and all, I wonder if I could use this microwave oven transformer and some of it's accompanying circuitry with it's capacitor and pwer it from an inverter for this experiment.

http://public.bay.livefilestore.com/...011.jpg?psid=1

http://public.bay.livefilestore.com/...009.jpg?psid=1

I also bought these variable Air capacitors but I don't think they are up to Kv ratings. Maybe hundreds of volts hard to tell I haven't received them yet.
http://public.bay.livefilestore.com/...aps.jpg?psid=1

I hope to get another variable air cap with about 1/4 inch air gaps, for HV it's a long one.

I understand that a MOT should be current limited for safety, so I will need some of it's original circuitry or a different way to limit the current to below certain death level's, whatever that is.

Anyway getting some things together. Slowly.

Cheers

[Jetijs]

Farmhand,
those things are great and valuable, but I am afraid not for this project. The capacitor has an internal resistor in it and is not intended for high frequencies. The transformer is not very efficient, it usually consumes around 100w just idling, also it can not handle high frequencies as its core material is not intended for that. And those air capacitors are also not rated for high voltage, anything more than 500v will cause an arcover. Also their capacity is way smaller than needed, usually at around 1nF max.
Sorry to burst the bubble.
Anyway, those items are great for many different experiments and should be in any experimenters arsenal

[Farmhand]

OK no problem, thanks for the reply, I was scrapping the microwave anyway and it's a good excuse to learn about these things. I'm just gathering as much stuff as I can get, and learning what I can.

I don't have a bubble to burst. So don't let that bother you, I prefer to hear straight talk anyhow.

Thanks
Cheers

[deggers]

I know this link has been posted on this forum before, but the Tesla patent is so relevant to Don's device.

Freeenergyinventions

[Djacs]

High current in water

Hello Jetijs,
I am trying since few week, to pulse sparks with high current and low voltage as possible between two pieces of metal, at different frequency, in the aim to
produce a lot of HHO. I bought few old car coil, transistor, resistor, etc... but
i am to ignorant to succed alone. Could you help me or send me an electronic plan that would make it ? Thanks very much. Djacs.

[Djacs]

Hello Jetijs,
I am new in building electronics together. For exemple, concerning the diodes bridges, what does it mean those 2 values together ( 1000 a and 10 a) ?
you mean that is the variac that could impulse such values ?
Also, what is that relay that have a condensor +- inside ?
can i buy this piece somewhere? what is his name ?
I really want to achieve your plan, that is why i need very precise descriptions. Also, i have seen the price of variac at variac.com, it is to much for me. Could i replace those 2 variac by something else ? build my self something else ? Thanks by advance for your answers. Djacs.

[Djacs]

High current sparks low voltage

Hello Jetijs,
I am new in building electronics together. For exemple, concerning the diodes bridges, what does it mean those 2 values together ( 1000 a and 10 a) ?
you mean that is the variac that could impulse such values ?
Also, what is that relay that have a condensor +- inside ?
can i buy this piece somewhere? what is his name ?
I really want to achieve your plan, that is why i need very precise descriptions. Also, i have seen the price of variac at variac.com, it is to much for me. Could i replace those 2 variac by something else ? build my self something else ? Thanks by advance for your answers. Djacs.

[infoleather]

Whether you have or not, do you have any details of the construction of the coil or transformer?