Tesla / Imhotep Radiant Energy Circuit

[soundiceuk]

Here is the wiring diagram as promised:

http://i1108.photobucket.com/albums/...uitdiagram.jpg

I now have a quiet running circuit, so glad to get rid of the buzzing 5 pin relay.

Every bulb I have tried is brighter but I have exceeded the physical limits of the coil I am using. It is the old cylinder type which I believe has an iron core.

I am going to get a motorsport ignition coil, which I know has a ferrite e core to try.

After that, I am going to start wiring coils in parallel to find the impedences needed before getting a custom coil manufactured. I got this idea from Lidmotor who did it with two coils, they were both iron core I believe from looking at the videos.

The most interesting bulb is still the xenon. I went from two strikes of lightning dancing around to around 10-15 straight lines and increased brightness.

Needs higher current, higher voltage and a coil which can handle the higher frequencies better.

A transformer manufacturer informed me the ferrite cores they sell handle 20hz-100khz. This sounds ideal, hence going for the motorsport coil first.

Would also like to try 4 x coil on plug (pencil) wired in parallel. I just need to find out the trigger voltage needed.

The brightness can be checked with lux/lumen meter

[jimboot]

@letsreplicate will be getting back to it tonight. Still have not plugged it in.

[jimboot]

No joy The only thing that I can see that I could be doing wrong is that the ceramic caps may not be 20pF . The top of them have been dipped in black and I'm guessing that may indicate a multiplier? Like the ones below My aerial was a piece of aluminium which was sitting on a plastic crate but not elevated.

[jimboot]

actually i'm thinking that the black indicates they are low voltage therefor inappropriate for this experiment?

[LetsReplicate]

actually i'm thinking that the black indicates they are low voltage therefor inappropriate for this experiment?

Some ceramic disks wear a color "skull cap" to indicate the dielectric. These will also use a XXM format to indicate value (where the M is the multiplier), and a tolerance letter from Table 5 above.

For example, 102J with a black cap would a 1000 pF 5% C0G. There is a similar system for Class 2 and 3 ceramics.

For instance, a C0G will have 0 drift, with an error of ±30 ppm/°C, while a P3K will have −1500 ppm/°C drift, with a maximum error of ±250 ppm/°C.

The band does not mean voltage, it refers to temperature drift. Ceramics can usually take a few hundred to 1kV before breaking.

The reason you are getting little to no output is the capacitors have too little capacity to let through signals that are a lower frequency than the one you are trying to receive.

If you replace those capacitors with 0.1uF, or 0.22uF you should have a marked improvement in your output. As the capacitor value goes up: so does your receive bandwidth.

[importfanatik]

test tubes

well,. it seems I am now the proud owner of 200 test tubes thanks to a lucky find at a local pawn shop. About 199 more than I needed.
Now I need to find a decent LCR meter so I can tune the coil..

I also found this link which talks about 5.4Mhz and "RF Energy via solar ionospheric resonance" which is worth reading

[kcarring]

@sounddiceuk

I have a coil that i got and i am wondering if it be OK, its called a MSD Blaster 2 PN 8202

Blaster 2 Coil Hi-Performance - 8202

Coil Specs
Turns ratio: 100:1
Primary resistance: .7 OHMs
Secondary resistance: 4.5K OHMs
Inductance: 8 mH
Maximum voltage: 45,000 Volts
Peak current: 140 mA
Spark duration: 350 uS


It says you have to add a resistor if you are using it with a vehicle that has points...

thanks

[soundiceuk]

Hi, its a real funny coincidence you asked that.

My search for the most powerful ignition coils on the market has been taking place over the last few weeks.

Here are my findings:

MSD Ignition Products

The 8201 is a beast at 55Kv and the 8208 must be a super beast as its more than twice the price.... no specs though?

More specs for MSD coils on on http://www.realsteel.co.uk/section9.pdf (page 5)

I'm not sure how suited they would be because they need a circuit to ramp up the voltage from 12v - 18v to 460v - 630v through capacitive discharge and the igntion modules are super expensive so would need custom pcb design. I have just made an enquiry about this to RM Cybernetics RMCybernetics - Research Media & Cybernetics

The standard ignition coil I have been using has a 3.5ohm primary and a 7900ohm secondary.

I have also used a 240v-18v laptop transformer for much weaker lighting effects.

As long as your ignition driver has the fuse there it should be fine. Maybe just put a smaller fuse in there to start with and an ammeter to see whats happening.

I'm certain you will be getting better results than me.

I'm awaiting some money so I can buy a number of different coils to experiment with. Wiring them in parallel until I find the point when one of these horticultural bulbs fires at, no doubt it will require seriously less power than the conventional way.

Hey, its makes sense that the elite make the most money they can out of the methods of lighting that are available to the marketplace.

Think about this:

1. High voltage neon sign transformers powering neon signs.
2. Flurescent strip lights have ignitors and then get fed with 1000v.
3. Xenon bulbs in cars have HID units. Now this is taking 12v and upping the voltage to a point the bulbs light up.

Now one of these is far more efficient than the rest but very few question how these lights really work.

Look forward to some pictures / video of the Blaster II in action!

I bet the results smash mine to bits... They are quite cheap, I've been wondering if maybe this is the coil to go for multiple coils in parallel with.

The other one I fancy is the Cosworth Group A coil Rapid Ford Limited

Looks like it might be a ferrite e core. They were used in the Group A Rallying back in the 80's - 90's.

If we knew the figures needed in ohms, mH etc... we could get custom coils made.

The ignition coil websites that may be useful are:

Mallory Ignition, Manufacturer of High Performance Racing Ignition and Fuel Systems

Performance Ignition MSD, Mallory, and Taylor Vertex, dealer

Taylor Cable Products - Spark Plug Wire Sets and Acessories

ACCEL Coils - Universal Coils, Racing Coils, Super Coils, GM Coils, Ford Coils, Chrysler Coils, Canister Coils, Coil on Plug


The note about the ballast resistor means.

The coil on cranking the engine would be fed direct from the battery 12v positive through a relay. Once the engine had started the coil would then be fed a 12v feed to the ballast resistor, which will knock it down to 9v.

This is to facilitate better cold starting.

If you have the ballast resistor you might want to try running it from a 9v Nickel Metal Hydride battery and feed the secondary HT from the bulb back to the positive of the battery and see how long it runs for. This is an experiment I wish to do.

[soundiceuk]

well,. it seems I am now the proud owner of 200 test tubes thanks to a lucky find at a local pawn shop. About 199 more than I needed.
Now I need to find a decent LCR meter so I can tune the coil..

I also found this link which talks about 5.4Mhz and "RF Energy via solar ionospheric resonance" which is worth reading

Interesting link, thanks.....

Strangely, as you do I ended up on The Sea of Energy by John E. Moray which is an interesting read.

This coil looks the business too!

UNIVERSAL ULTRA COIL BY JACOBS - Coils & Accessories - ACCEL

Spoilt for choice here lol! Dynatek | Accessories | Dynatek Motorcycle Ignition Coils

[soundiceuk]

The note about the ballast resistor means.

The coil on cranking the engine would be fed direct from the battery 12v positive through a relay. Once the engine had started the coil would then be fed a 12v feed to the ballast resistor, which will knock it down to 9v.

This is to facilitate better cold starting.

If you have the ballast resistor you might want to try running it from a 9v Nickel Metal Hydride battery and feed the secondary HT from the bulb back to the positive of the battery and see how long it runs for. This is an experiment I wish to do.

Sorry forget the bit about "If you have the ballast resistor".... where were my thoughts then?!!! lol

My chain of thought was It would be very empowering to see a 240v 600w bulb fully illuminated from such a small power source.

I believe this is 100% possible and will be achieved in the very near future.

I also believe with the right transformer and electronics a very simple inverter could power your house whilst charging the small battery.

I wish I had the money for a scope and more time to spend on these projects.

[spark2]

whre are you all this thresd semme dead

[chips2041]

Hey All

I am working on putting together a video. I think i have a way to explain all of this finally. I posted on another thread here that I will be making a video soon.

What is actually going on with the Tesla/Keely/Moray energy generator?

Well start with the crystal/foxhole radio. It will lead you to understand that there is static (and a lot of it) energy everywhere at different frequencies. Everything has a frequency. The natural frequency of the earth is 7.82hz and is known to actually have healing properties (although that might be some of the hype to get people looking at it).

So make a simple crystal radio and look up the formulas to figure out how to make a coil resonate at different frequencies. Solar resonates with UV or infra-red with some of the new crystals/nanofiber antennas they are making.

380khz can produce roughly 2kw (provided it isnt being used to broadcast a radio station in your area). The need for this circuit is kind of null. The "Tesla Secret Circuit" or whatever is nothing more then a quadrupler (bad spelling sry -- seek out the radio shack circuit book -- its out there somewhere).

The catch to the natural sounds of the universe is that they are very low amper and naturally DC (which explains the need for a ground). This means we must use impedance and reactance....not resistance in order to power an induction coil for usable power.

Something similar to a crystal radio set ----> A magnetic induction coil (like the early magnetic headsets just without the film that reacts to the magnetic field).

The magnetic field that is being produced by the sound at 380khz can induce a magnetic pulse 174,000 times per second (about). This can produce roughly 2kw because the magnetic field wont be very large (so the induction coil also will not be able to be very large).

It is all solid state power production. Its converting frequencies that exist throughout the entire universe into power. The frequencies that are already being used for radio waves will have a lot of that natural power already being used to aid in carrying those signals. Many people forget that Tesla saw the earth as a huge capacitor (which it is). The universe is constantly hitting the earth with thousands of different frequencies (many of which we probably cant even record yet). Lighting and other effects take advantage of these frequencies (also called pulsars and many other names due to the fact they come from all different things in the universe including us). Ions keep the neutrons and photons from making contact. You can essentially ionize a small portion of the air creating cavitation, except with photons and neutrons. This cavitation will naturally be filled (this is induction with low current -- this effect makes it cost less to fill then it does to drain giving you the ability to capture the drained energy at a much higher wattage then it took to produce (over-unity)). Look at electrons like they are drops of water and the wires are pipes. In most cases cavitation is a bad thing....in this case we use it to our advantage to make a better drain. Hope this helps

[FRC]

Nasa Nate

What kind of amperage do you get? You should post all this on the Cosmic Collector thread.

George

[Nasa Nate]

thanks i moved it

[Thane]

Off talk, but still :-)

Please do keep us updated Chip! I noticed your posts after a whole day of searching for information on, how to create a Tesla Generator.
I Ended up on THIS SITE several times, and today I decided to check it out.
So I filled that Exclusive Video offer with my name and E-mail, verified, and watched something I really didn't expect, since I were not searching upon that as you could imagine.

Now I believed in these conspiracies, illuminati, NWO, False flag operations, aliens, etc. Just the top of the mountain. And its pretty obvious too notice the truth
They created this "modern capitalistic economy money consuming materialistic Resource Horny police state society system, filled with stress in the west and poverty in the east."
Led by big time Bank'sters' out of the ordinary people, they are the ELITE! :-(


Seriosly ... I believe the 'aliens' have tried to Help, guide and simply tell us the truth for a long time, but, no no no.. We are too ignorant!

Now Chip2041, please provide us more information, I cant wait for seeing that video of yours :-)

Sorry for the off talk guys, I have a hard time stopping, cause it makes me so angry to know that most people wont care about it, and that indicates their big plan worked...


Best regards
Thane