The electric field of a magnet

[Dave45]

We looked at Birkland currents awhile back, I think this is the solution, stripping electrons and protons from the magnetic field using dielectrics.

We cant stop the magnetic field which is a blessing, but we can remove the particles that orbit it using dielectrics, we do it everyday by using laminated plates in a transformer.

[Dave45]

Epoxy Resin Circuit Board Potting Compound Waterproof Masking Sealant 96 oz Kit | eBay
SOLENOID COIL EPOXY POTTING WITH MAX MCR EPOXY RESIN.wmv - YouTube

It depends on your setup but I wouldnt pot the secondary only the primary,
Im thinking about potting the core with the copper wire wound around the welding rods to see if lenz can be collected in the core, in an asymmetrical setup.

[Dave45]

Hey guys Im off for a couple of days so Iv been reading the forum some very interesting discussions going on, I particularly enjoyed the Stinging Impulse Rays thread but will refrain from interrupting the thread.

I have been studying the common alternator you know me crazy idea's
trying to understand how the coils are getting energy from the magnetic field

If we take the Birkland current theory, which has been proven
we have compressed space with high energy particles orbiting it, or I should say high energy particles orbiting each other and compressing space.
I think what we are seeing here is a magnetic field line being orbited by the electric field.
We cant stop the magnetic field line after it has been created from passing through anything but we can strip the electric field from it.

Ok back to the alternator we have an iron laminated toroid core with coils wound in it, I think the magnetic field (compressed space) is attracted to the iron because just like electricity it runs through metal (iron) easier than air.
But the electric particles that are orbiting and compressing the field dont like to run in the iron so we have a buildup of electric particles at the face of the iron, if too much pressure (over saturation) occurs the electric particles are forced into the iron causing heat, just like iron wire heats when you run electricity through it.
The coils being in the position they are, carry off the electric particles because like the compressed field they travel easier in metal (copper).
So the iron to a certain degree is stripping the field of the electric particles and we can see that laminated plates work even better at this.

I dont see why we cant do this very same thing in the core of a magnetic field,

Just some thoughts, I am working in this direction.
later
dave

[Dave45]

Asymmetric alternator

I just love it when they say it'll never work, dont waste your time and money
Notice the north and south claws are out of phase

I need one more stator

[Dave45]

Im surprised that the magnetic field from this small toroid magnet is as strong as it is, I can pick it up with a compass over a foot away.
The magnet is from a microwave magnetron.
I need a longer shaft, will have to search the junkyard.
The stator is wound using s winds not a complete circle, interesting, I may leave the stator winds as they are to start.
later
dave

[Dave45]

Hey folks me again
I think we need to take everything we read with a grain of salt, especially from those in high academic standing, and that includes my work. I tell it as I see it at the time and is always subject to change as I learn, if I ever stop learning I'll quit because I will be no good to you or myself.

I have been studying the alternator and trying to understand below is a pic showing the rotor cutting the stator wire, the alternator has an unusual winging its an s winding.
I can understand why a alternator would be nowhere near efficient the fields cutting the wires are running against each other in a number of different ways.

By reversing the claws on the alternator we have created a type of homo-polar generator and will be very interesting to check out, but Im sure the stators will have to be rewound.

[Dave45]

I think for the homopolar gen the winding on the stators needs to be wound like this, one side cw and ccw on the other, direction of rotation will also be important.

[Dave45]

by winding the wire around the stator the poles should add to each cut of the wire
Will be interesting to find out.

[Dave45]

this guy cracks me up, but what I wanted to show everyone is the iron ring he uses to separate the pos and neg charge.
300Kv On A Television - YouTube
I watched a vid simular to this where he used the ring about a year ago but he took down his vids, but found this today and wanted to bring attention to it.

Why is the iron ring stopping the arc over, does it create a magnetic field that cant be crossed by the electric field, very interesting.
Brings to mind the wheel within a wheel written of in the Bible.

dave

You gotta watch his vids Photonicinduction - YouTube

[Dave45]

[Dave45]

Has Kurt (Mr.Clean) found the key we'v been looking for, Juno - Science:Magnetosphere

[MonsieurM]

Dave , thought this might interest you

Thomas Henry Moray: Speech at Valley State College, Northridge CA

This type of energy device is capable of converting the high frequency, high level of the cosmos, kinetic radiations by synchronization, into usable frequencies and voltages. Basically the theory of operation is as follows:

Oscillations by synchronization are started in the first stage of the circuit of the device by exciting it with an external power source such as the difference of potential between two points. The circuit is then balanced through synchronization until the oscillations are sustained by harmonic coupling with the energies of the Universe. The reinforcing action of the harmonic coupling increases the amplitude of the oscillations until the peak pulses "spill" over into the next stage through special detectors or valves which then prevent the return or feedback of the energy from the preceeding stages. These oscillating pulsations drive each succeeding stage which oscillate at a controlled frequency and which are again reinforced by harmonic coupling with the ever present energies of the Cosmos. That is, the first stage drives a second stage, the second stage driver a third and so on. Additional stages are coupled or until a suitable power level at a usable frequence voltage and amperage is obtained by means of special resonant oscillators.

Once the device is in operation and delivering energy, it does not require the continuance of the original excitation induced by the difference of potential between two points to maintain the oscillations. The oscillations are sustained as long as the device remains properly synchronized and the external circuit is completed through a suitable load. This load may be maintained at as low an output as 1/4 watt, The special tubes which are the key to the successful operation of this device are specially constructed ionic, cold cathode tubes.

All energies of the plasma of the Universe have resilient rigidity and density, which is subject to displacement and strain. When a resilient substance is subject to strain and then set free, one of two things will happen, The substance will slowly recover from the strain and gradually obtain its natural state or the elastic recoil will carry it past its position of equilibrium and cause it to execute a series of oscillations. Something of the same sort will also occur when an electrified capacitor is discharged through special high frequency valves.

[Dave45]

Hey MM good to read ya bro
Very interesting info, you can just feel the truth in his words, like he's done it already

Once the device is in operation and delivering energy, it does not require the continuance of the original excitation induced by the difference of potential between two points to maintain the oscillations. The oscillations are sustained as long as the device remains properly synchronized and the external circuit is completed through a suitable load.

I especially liked this part, he looped it
Thats what we have to do,
Tesla used vacuum tubes (valves) in his Car
Hmmmmmmmmmm makes a person want to fry some vacuum tubes
One thing Iv learned since delving into this en devour is parts are very hard to source, we need to be able to make our own.

[Dave45]

I know what these coils do,

[Dave45]