My Motors got me to Tap into Radiant Energy

[prochiro]

Ufo

I have emailed Peter Lindemann but no answer yet.
Dana

[thugugly]

In UFO's first post, he mentioned peter Lindemann sent him to Energetic forum. If someone knows lindemann, maybe he knows UFO.
Could Aaron, the administrator, get his name or phone number to reach him, from his account.

[thugugly]

Sorry, you posted when I posted.

[prochiro]

Ufo

I talked with Peter L. and he said that he was too busy to help and that all we can do is wait. I sure hope this is all about a computer problem.
Dana

[Ufopolitics]

Hello to all and thanks so much for being worried, I am fine

Hello to all my Dear Friends!!!

I am just fine, thanks for your concerns, and I am very sorry it could not be released yesterday, nothing happened, it is just that I really underestimated the amount of time that rendering and prepping all text, scenes, etc takes...
I went to bed last night around three am...with lots done...but not finished.

The thing is I want to make it as clear as my expertise in this 3D Softwares allows me to...Don't want confusions...so anyone from whatever level of knowledge has it.

What am working on right now is a 3D Model of a Symmetry Model based on Mr Lindemann video on YT (the tests and diagrams) but I have made my own graphics, same values. Then I have also done the same model but in Asymmetrical Mode...showing both differences and great advantages, no magic, everything would be very well explained...with a little humor..

I am also going to show a Lab Video, where I put together a five pole little brush motor (Radio Shack part#273-256), -The receipt marks # 2730256-is a
Five pole armature with two permanent magnets, they cost $5.39 ea USD,you will need two of them..This simple replication of my video set-up will output from 18 to 21V when fed linearly straight from a small Lipo battery of 10.0V (almost discharged)...but well, the more you input the more we will obtain out...
I will show in detail the CAD windings and all hookups to build it...

Again, I am sorry about the delay in posting, and about my video, but I have tried till exhaustion yesterday to finish even later morning today...but couldn't...you will all see the complexity of the video and I know will understand...

Please bare with me here...it will happen soon (I do not want to keep giving future dates)..but very soon.


Regards and warm hugs to all


Ufopolitics

[thugugly]

Wtf

UFO,

I'm glad ,beyond words, that you are ok, but if you ever do that again, disapear and leave us hanging like that, DUDE, NOT COOL!

I was so pissed, I thougt they got to you, like so many others.

Peace and Love

Thug

[Sanskara316]

Thank God ur alright, that's the important part,

[prochiro]

Ufo

I will say for everyone here that we are so happy to hear from you. We have been worried sick that something was wrong. You just go ahead and take the time you need to do what you must do. Just take at least a few minutes each day to stop in and say hello.

Dana

[wonza]

So glad you're ok UFO!

Also, can't wait to see everything. Will you have a full parts list too? I'll be ordering everything I need to replicate this

[larryross]

Hello UFO
What a relief I was sure they got you especially when your website went down at the same time.
Small celebration...

Please take whatever time you need, just let us know you are still kicken.

Regards
Larry

[iankoglin]

Glad to see U R OK

Hello to all my Dear Friends!!!

I am just fine, thanks for your concerns, and I am very sorry it could not be released yesterday, nothing happened, it is just that I really underestimated the amount of time that rendering and prepping all text, scenes, etc takes...
I went to bed last night around three am...with lots done...but not finished.

Again, I am sorry about the delay in posting, and about my video, but I have tried till exhaustion yesterday to finish even later morning today...but couldn't...you will all see the complexity of the video and I know will understand...

Please bare with me here...it will happen soon (I do not want to keep giving future dates)..but very soon.


Regards and warm hugs to all


Ufopolitics

G'Day UFO
Like the others was Keen to hear from you again
I have been looking each couple of hours to se your post especially after the "Regards and Good by all" http://www.energeticforum.com/200273-post1123.html I thought something bad had happened

Regards

[bbem]

Ufo

Glad you are save and sound.
Now I do not want to hurry you, take your time, but maybe you could release something on Tesla's birthday 10th of July.
Nikola Tesla Timeline 1856 - Birth Of Tesla

Bert

ps. Liked the idea that you send us info up front what to collect/buy for the next step.

[Les_K]

ufo

Whew!!!....

Les

[aaron5120]

Thanks God that Ufopolitics is safe and healthy! We pray that he be well and will finish his great mission soon to give the world the Great Breakthrough to the next paradigm shift.

[iankoglin]

G'Day UFO and all others
I really like to thank you all especially those that helped me to try and debug my machine

Now with Torpex and Larry's input
I made up a single Mosfet circuit and used this to see if the Regulator and then the Oscillator were working (so I would only Smoke 1 Mosfet)
The regulator does work the 555Oscillator does Oscillate but I think it is not sending the proper signal or is not strong enough as it seems to change the frequency along with the duty cycle.

@ Larry
I was originally using Bob's Oscillator and when I was having trouble(Thats me all over) You suggested on page 28 post#111 that you modified this oscillator but as UFO suggested we should keep it simple and use the 555 Oscillator so I continued with it
The others all seem to have success the Bob's updated LM339 Oscillator page35 post #1026 Here
http://www.energeticforum.com/199376-post1026.html

or perhaps Larry I should build the one you have posted on page35 post #1029 the one also showed on page 28 post #111 it is here
http://www.energeticforum.com/199382-post1029.html