My Motors got me to Tap into Radiant Energy

[prochiro]

Tow

Hi sputnik
The carbon tow (thread like) has not provided to date, enough power to go to all that trouble. The one or two inch wide CF does provide much voltage but little amps. But so does copper coils. Bob may aggree or may not, I do not know for sure, but while he is testing the CF, I would concentrate time and money in other areas of this tech. Use copper secondaries for now as if the CF does work better later, everyone can add that later. What I see to date is that the copper is actually cheaper, easier to work with and doing an equal job. The superconductor thing about CF may show better than copper if higher volts and longer lengths were used but with what voltage we are using now, myself, I can not see the advantage yet.
Dana

[sputnik]

back Dana!
Thanks much, good info there. I still may give it a go after I scan back thru the thread a little, I did find it was pretty cheap here, first hit on Google, I'd look more carefully 1st though. I though Bob had some really good results with it but so much going on maybe I was confused. My ship finally comes in tomorrow, so big order day Buy buy buy
Got a nice scope on ebay today, don't have to put up with the PC audio card thing. Worked with good scopes all day for many years, don't think I could have lived with that for long. I know it's not needed a lot here yet, but we'll see.

[prochiro]

CF

Hi sputnik
You will like the new digital scopes and learn more from them. As bob and I have seen with the flat tape shape CF, it does not work well as a primary coil. Short pieces (6 to 12 feet) do well as secondary when placed first on a core but not when put into the core center. Bob has even placed CF and copper in alternate layers but found that it seems as whatever energy the copper produces can be collected in one short strand of CF. CF can only collect what you cause to be generated and it will take only a small amount to get it all. Buy maybe a couple 12 foot sections first. The CF is not magical but is a super conductor so may be overkill for the voltage we use. You can do the exact same thing with copper or CF at out voltages now. We have gotten just short of 600 voltes from 12 volts with nothing really for amps in both copper and CF. Stay with UFO if you can with current teaching and do not get lost on CF. There will be plenty of time later to tune up a system once it is togeather. I am sure that Bob would like to have more ideas on CF but is hard to reach due to communication blackouts, no power and limited phone availability.
Dana

[AllPhase]

good points.

Good points.

[prochiro]

CF

Hi sputnik
One thing I forgot to mention is that we used 1/16 heat shrink to house the CF tow. After heating the finished tube, it was vary small in diameter. However, it seems that one of the reasons that the tow is poor is that even with that small of distance between the tow wires, it is too much. The flat one inch and two inch wide CF workes because the covering is food rap and the surface is a wide solid layer. We have found that CF is so totally absorbing everything in its surface that rolling it two layers thick does nothing more as everything goes into the first layer. Nothing gets thru to second layer. I hope you get what I am saying. The fabric you are talking about is maybe much thicker than food rap and will seperate the coil CF wires too much.
Dana

[sputnik]

Hi Dana
And thanks for even more valuable info. Yes, I do understand exactly what you are saying. Although plastic sheet tightly sewed could do well too, but I grasp what you mean. And it sounds like you have gone to quite an effort to understand it.
Yes, I got one of those fancy new scopes (used of course). It was quite cheap and although I could have gone even cheaper with a quite usable old style scope size is important to me, they are too cool being so thin. Where's the big suitcase that's supposed to be behind it?
Did order, order, order today. Much coming from China, so about 2 weeks before I can really get rolling. I also did get a small quantity of TOW, 2 6 foot pieces of 48K for some general fooling around ($3.50 delivered), we'll see where that goes. Since you set me straight on that issue I'm not going to let it hold me up, but I do have some ideas I wish to try.
Tomorrow the last of the ordering (components for the PWM setup) and then a trip to Radio Shack to see if I can save the shipping cost on the two motors. Then maybe I can do something besides twiddle my thumbs waiting on shipments.

[Lightworker1]

Hello UFO,
Thanks for presenting vision regarding carbon fibers and their possible use in circuits, motors and ant-gravity devices of future. It was enjoyable and exciting read.

Regards and Many Thanks

[gsmsslsb]

Hello ufopolitics
This is my first post in this thread.
I have been reading through the preceeding pages but I do not have my own internet connection so a lot of the pages are blocked I am not sure why. (maybe they have bad language etc)
I have read the pages that I can and I would like to replicate the coil device.
if you have a few moments could you look at this link starting on page 3-124.
http://www.free-energy-info.co.uk/Chapter3.pdf
It is patrick kelly's condensation of the information in this thread to date.
If there are any glaring problems with the information at that link could you point it out. I think it may be a good resource for all those trying to get up to speed here as it has a lot of the information together that is spread out through the thread.
Thank you
LV

[iankoglin]

At Last Kogs has the light

G'Day ALL
I have just now got my RS Motor going on the other thread and I decided that seeing so mant tried to help me see the light I must now try and see if I can -------WELL HERE IT IS

Kogs UFO Photos :: Kogs sees the LIGHT video by Kogs1 - Photobucket


Now I am sure it will be plain sailing from here on

@ Larry where is your setup I keep looking for it, have you finished it yet
Please show us here I am sure we would all like to see it


Kindest regards especially to you UFO AND all THOSE that helped me

[iankoglin]

Kogs Update

G'Day ALL
I have just now got my RS Motor going on the other thread and I decided that seeing so mant tried to help me see the light I must now try and see if I can -------WELL HERE IT IS

Kogs UFO Photos :: Kogs sees the LIGHT video by Kogs1 - Photobucket


Now I am sure it will be plain sailing from here on

@ Larry where is your setup I keep looking for it, have you finished it yet
Please show us here I am sure we would all like to see it


Kindest regards especially to you UFO AND all THOSE that helped me

G'Day UFO and All

I just now connected a small Motor instead of the CLF Bulb
It is a MY68 24v 6amp
I went really well I could not stop it
I then replaced it with a larger motor
A MY1018 36v 9.5Amp
It really took off I had to stop it as the heatsink was heating up very fast.

I really should get my Camcorder lady to take some vids
She said she has to learn how to use it first

My Friend Andrew is still trying to find 2 Windscreen motors to make one. He has several from the same make and model cars but they are all different he has decided how to fit the parts together to make one now so I imagine I should be able to wire one up soon.

Regards to all



Still trying getting there

[woopy]

Hi all

i am very happy to replicate this fantastic experiment

good luck at all

laurent

cold electricity testing replication 1 - YouTube

[Ufopolitics]

Excellent Testing Woopy!!

Hi all

i am very happy to replicate this fantastic experiment

good luck at all

laurent

cold electricity testing replication 1 - YouTube

Hello Woopy!!


Excellent testing!!...very simple Uh?...
Nice set up you've got there my friend!!


Thank You!


Ufopolitics

[Ufopolitics]

Ian I am very happy it is working excellent !!

G'Day UFO and All

I just now connected a small Motor instead of the CLF Bulb
It is a MY68 24v 6amp
I went really well I could not stop it
I then replaced it with a larger motor
A MY1018 36v 9.5Amp
It really took off I had to stop it as the heatsink was heating up very fast.

I really should get my Camcorder lady to take some vids
She said she has to learn how to use it first

My Friend Andrew is still trying to find 2 Windscreen motors to make one. He has several from the same make and model cars but they are all different he has decided how to fit the parts together to make one now so I imagine I should be able to wire one up soon.

Regards to all



Still trying getting there

Hello Ian!!


Ian, I am very happy it is working excellent for you my friend!!


Nice!!


Regards


Ufopolitics

[Ganzha]

Hi all

i am very happy to replicate this fantastic experiment

good luck at all

laurent

cold electricity testing replication 1 - YouTube

Hello ! Dear Woopy! U doung reat work with your experiments!
Thank you very much!!!!!

I have schematics of one exp thatI woud like to replicate but I havent induction cooker, maybe you have a cooker and a wish to perlicate this?
cooker- YouTube

[Ganzha]

Motor as a Charger

Hello UFO!

I have one idea how to convert a Electro scooter of my son into some kinda Perpeum mobile

I woukd like to know your opinion


Thanks

Vadim