Announcement

Collapse
No announcement yet.

My Motors got me to Tap into Radiant Energy

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Originally posted by woopy View Post
    Hi all

    i am very happy to replicate this fantastic experiment

    good luck at all

    laurent

    cold electricity testing replication 1 - YouTube
    Great Experiment.
    Thanks and Regards

    Comment


    • Catching the Radiant energy

      Originally posted by Patrick Kelly View Post
      Hi Ian,

      Thank you for your video, it cleared something which bothered me a lot. My setup is running on 24V with just one IRF740 FET and four parallel strands of 22 swg enamelled copper wire wound side by side, over a double layer of 20 swg wire on a 2.5 inch long 2 inch diameter spool. Increasing the Duty Cycle does what your system does and at quite low settings the light output gets to a scary level, giving marked after-images if you look at it.

      What bothered me was that increasing the Duty Cycle increases the power output, while my understanding of the theory was that as the cold electricity component is supposed to be fed in the OFF periods, so raising the Duty Cycle should lower the output power and not increase it, but I see that you are getting the same effect as me.

      My inner coil half-wave rectified into a capacitor is giving me 116V which I have not yet load tested. Have you tested an inner coil? It would be nice to get this setup self-powered which I believe should be possible.

      Patrick
      G'Day Patrick
      As I understand it the Radiant energy is produced at the instant that the current is switch on and when the current is switch off for a nano second she continues before she dissapates and this is where we capture her.
      If the switching of the current is fast say 500 hrtz then She appears to be continual and therefore is usable She is a very versatile as whatever energy is required she can supply it,

      Kindest Regards



      Kogs @ work

      Comment


      • oscillator build

        Hey ufo and everyone,

        I finally got a chance to download the video of the oscillator build. Mostly, I just wanted to show people with very little skills, what the scope looks like at the different build stages. Its all in one of John Stones post, his driver circuit is there also in another post. One thing, you won't get a reading at output of driver until the fet and load are connected. Remember to tie all grounds together (coil,oscillator, driver).

        I've got 4 completed, but something is telling me I need 10.

        Ufo, this is a tremendous amount of info for someone like myself, I hope you do not lose patience with me/us.

        Here is the link (photobucket is way too slow uploading, wasted hours, I had to open a yt account):

        oscillator build - YouTube

        Comment


        • PWM build documentation

          UFO expressed an interest in having someone detail their build of the PWM. Since I am just now building mine it was easy enough for me to do just that.
          I've only made the oscillator so far and it works great. I will add another similar post when I decide what I'm going to do with the drivers/MOSFETS, I'll be using the 555 drivers.
          This build is based upon John Stone's V2 schematic. I believe we also owe MadScientist a thank you for finding this nifty circuit in the 1st place.
          Instead of the two LM393 dual opamps that John Stone drew in the schematic I used a single LM339 quad opamp. This works just fine, is probably a bit cheaper and smaller but the pinout is different. This can cause nightmares (first hand knowledge!), so I suggest if you use this information to print out John's schematic, cross out the pin numbers on the U1 and U2 IC's and update them according to this:

          EDIT: It seems opportunity for error, this step, I wanted to post a modified version of John Stone's schematic, but he is on vacation and I certainly don't want to do it without his permission. So instead I redrew the schematic and have posted it. Just download that and forget this step. It is very high resolution, doesn't appear well on the Picasa site, but if you download it it will work fine for you. Additionally it has DC voltages marked from a working model.

          U1 pin - new LM339 pin
          3 - 5
          2 - 4
          1 - 2
          5 - 7
          6 - 6
          7 - 1

          U2 pin - new LM339 pin
          3 - 9
          2 - 8
          1 - 14
          5 - 11
          6 - 10
          7 - 13
          Additionally, whereas the LM393's each had power supply connections on pins 4 & 8, you now have only one set of connections on pins 3 (positive) and 12 (ground).
          In the photos you will find a "bug ugly" layout that I used for my working model. The layout is almost as ugly as the build, I'm trying to ween myself off of Photoshop to GIMP. Anyhow it does clearly show how to assemble the oscillator as quickly and as painlessly as possible (I hope!).
          Sorry, I can't figure out the photo upload thing, but here are the links to the photos in a Picasa album.
          Modified schematic
          Layout
          Component side of board
          Solder side of board
          Switch detail
          Frequency pot detail
          Duty cycle pot detail
          Actual output
          More actual output

          Good luck to all future builders!
          Last edited by sputnik; 08-20-2012, 06:43 PM. Reason: add updated schematic

          Comment


          • Originally posted by larryross View Post
            Hello UFO
            Thanks TBO I was just going over the Beck site.

            Looks like I have hijacked your thread... I really didn't intend to. I am very sorry. Should get back to the device and go forward.

            Regards
            Larry
            Hello Larry please consider watching dr Naram's Cancer Cure Parts 1,2,.. Some people found useful. Wish you good luck. He presents in both English and Hindi

            Cancer Cure Part 1 - YouTube

            Comment


            • Nice Video - which Circuit?

              Originally posted by woopy View Post
              Hi all

              i am very happy to replicate this fantastic experiment

              good luck at all

              laurent

              cold electricity testing replication 1 - YouTube
              Hi Laurent

              Nice video, can you confirm which circuit diagram you were using to drive the CFLs?

              Regards

              John

              Comment


              • A lot to learn!

                Hey UFO,

                I've enjoyed your asymmetric electrodynamic machine thread so much I thought I would join on this thread too. It's very interesting!! Your willingness to disclose your knowledge so freely is really great!! Thanks!

                I've been teaching myself electronics this past year so this will be great test. Hopefully I won't bother you too much with stupid questions.

                I'm only on page 14 of reading this thread so I've got a lot to learn before building a circuit.

                Cheers,
                Vince

                Comment


                • Hi John

                  here is the 555 circuit i have found on the net.

                  The output (3) of the timer goes through a 470 ohm resistor to the gate of a IRFP460 mosfet.

                  I have connected a 47 kohm between gate and source to better manage the fet shuting as per UFO shematic
                  than i connected a diode (1n 5408 ) between source and drain.
                  Ouups i just see that the 36 volt battery polarity is inverted in my shematic in the video

                  Finally the timer stage is independantly powered by a 9 volt battery.

                  Than you can test a lot of different coils at different dutycycle and frequency

                  as you can tune P1 P2 and C1

                  Hope this helps

                  Laurent
                  Attached Files
                  Last edited by woopy; 08-20-2012, 11:30 AM. Reason: Shematic check modif

                  Comment


                  • Hello Larry I remembered couple months back listening to People's Pharmacy Radio Prog about Dr. William Coley who was an American bone surgeon and cancer researcher, pioneer of cancer immuno-therapy. I felt I had to tell you. Dr Coley developed a treatment based on provoking an immune response to bacteria by inducing controlled fever under medical supervision. From the program interview, it appears this method is very successful in dealing with even very aggressive cancers which chemo+radiation is unable to deal with. Only recently in America this method has been allowed as alternative treatment on compassionate grounds by normal channels. In Europe it available. Here is the link for further info:

                    751 Coley's Toxin, Cancer and Immunology Archive - The People's Pharmacy®

                    You can also listen to the prog. There are audio podcasts. I personally think cancers are caused by bacteria etc rather than the medical science of the main stream unable to really cure it. I hope you and rest of the thread will forgive me for taking time but I had strong feeling this one method must brought be brought to the attention all. Best Regards

                    Comment


                    • Turion's posts gone

                      Maybe it is me ... Either that or my computer is playing games ... maybe my age is catching up..

                      Anyone else not able to see all Turion's posts in this thread

                      AV

                      Comment


                      • Originally posted by ampsvolts View Post
                        Maybe it is me ... Either that or my computer is playing games ... maybe my age is catching up..

                        Anyone else not able to see all Turion's posts in this thread

                        AV
                        Hi

                        Are you on the correct thread? - I confused this one with the electrodynamic machine tread the other day - maybe age as well!

                        Regards


                        John

                        Comment


                        • Hello Dear Patrick!

                          Originally posted by Patrick Kelly View Post
                          Hi Ian,

                          Thank you for your video, it cleared something which bothered me a lot. My setup is running on 24V with just one IRF740 FET and four parallel strands of 22 swg enamelled copper wire wound side by side, over a double layer of 20 swg wire on a 2.5 inch long 2 inch diameter spool. Increasing the Duty Cycle does what your system does and at quite low settings the light output gets to a scary level, giving marked after-images if you look at it.

                          What bothered me was that increasing the Duty Cycle increases the power output, while my understanding of the theory was that as the cold electricity component is supposed to be fed in the OFF periods, so raising the Duty Cycle should lower the output power and not increase it, but I see that you are getting the same effect as me.

                          My inner coil half-wave rectified into a capacitor is giving me 116V which I have not yet load tested. Have you tested an inner coil? It would be nice to get this setup self-powered which I believe should be possible.

                          Patrick
                          Hello Dear Patrick!

                          First I wanted to thank you for the great work you have done (in general) for all the Free Energy Inventors out there!!,
                          Second to thank you on the excellent work you have done on my Research and Development.

                          Now, the playing with the Duty Cycle should also be worked out simultaneously with the Frequency, as also should be ideal to be able to raise just the peak voltage output as we lower the duty, however in order to do that the Low Voltage signal, should be isolated from the Fet's Chanel Voltage...

                          There is exactly a range at very low frequency oscillations where you should get the lamp to go into a very bright white pulsating light, spectrum of purple, green...and white...after that by increasing the frequency and duty starts a process where the light starts going down to normal flickering till you get the high output at increased duty, light goes very bright again...but NOT the same spectrum as before though, as some "yellowish light" shows up...Right there it is NOT a pure Cold Electricity, but a "Mix" of both currents...I have recommended to use second diodes (after ultra-fast ones going to output) based on the small glass 1N4148, to do a better filtering, however, the disadvantage is your DVM's will go "blind" at output...

                          I still have to come back here and "finish up" this Chapter Disclosure...where I will bring the different Secondaries set up, as also another simple connection to "Enhance" this effect...but I have been very busy with my other Machines thread, however have to do here before I proceed there...

                          Thanks for posting here my friend, it is an honor to have you around Us!

                          Warm regards


                          Ufopolitics
                          Last edited by Ufopolitics; 08-21-2012, 04:44 PM.
                          Principles for the Development of a Complete Mind: Study the science of art. Study the art of science. Develop your senses- especially learn how to see. Realize that everything connects to everything else.― Leonardo da Vinci

                          Comment


                          • Cold Electricity

                            Originally posted by Ufopolitics View Post
                            Hello Dear Patrick!

                            First I wanted to thank you for the great work you have done (in general) for all the Free Energy Inventors out there!!,
                            Second to thank you on the excellent work you have done on my Research and Development.

                            Now, the playing with the Duty Cycle should also be worked out simultaneously with the Frequency, as also should be ideal to be able to raise just the peak voltage output as we lower the duty, however in order to do that the Low Voltage signal, should be isolated from the Fet's Chanel Voltage...

                            There is exactly a range at very low frequency oscillations where you should get the lamp to go into a very bright white pulsating light, spectrum of purple, green...and white...after that by increasing the frequency and duty starts a process where the light starts going down to normal flickering till you get the high output at increased duty, light goes very bright again...but NOT the same spectrum as before though, as some "yellowish light" shows up...Right there it is NOT a pure Cold Electricity, but a "Mix" of both currents...I have recommended to use second diodes (after ultra-fast ones going to output) based on the small glass 1N4148, to do a better filtering, however, the disadvantage is your DVM's will go "blind" at output...

                            I still have to come back here and "finish up" this Chapter Disclosure...where I will bring the different Secondaries set up, as also another simple connection to "Enhance" this effect...but I have been very busy with my other Machines thread, however have to do here before I proceed there...

                            Thanks for posting here my friend, it is an honor to have you around Us!

                            Warm regards


                            Ufopolitics

                            Hi 'UFOpolitics',

                            Thank you for your kind words and a very big thank you for sharing your knowledge freely with everyone. I am using 1N4148 diodes following the fast and powerful FR607 diodes, but I think I am getting it wrong as the tube doesn't really flash but strikes with a soft yellow glow. CFLs are not common around this neck of the woods, so the tube is a type which has three long U-shaped sections. Another thing is that frequency does not seem to have the slightest effect on the operation other than the light gets choked off eventually if the frequency is raised too much (not obvious at all why that should be). I have been driving the FET with a commercial signal generator on a separate power supply, but I will build a 555 version and do much more testing when I get the opportunity, but like you, I am buried under a sizeable load of other urgent work

                            Congratulations too on the amount of member participation which you have generated on your Asymmetric Motors forum - very impressive,


                            Patrick

                            Comment


                            • Priest Has Motor Run By 'Ion Energy'

                              Hi Ufopolitics, I have followed your excellent work for a while now

                              It's kind of cool how many of the threads seem to be crossing over lately.


                              I may be off the mark here but here is a research link Bruce sent out tonight and I just couldn't help but wonder what your opinion is of the patent. I'm not sure how relevant it is to your work, but if you or anyone else hasn't seen it before, you may find it interesting.



                              Priest Has Motor Run By 'Ion Energy'

                              Antonio d'Angelo -- Inter-Atomic Ion Motor -- NY Times article & US Patent # 2021177

                              http://www.rexresearch.com/angelo/us2021177.pdf



                              Also I wonder if Tesla's motor ties in too?

                              Brooklyn Eagle
                              July 10, 1932
                              Nikola Tesla States:
                              “I have harnessed the cosmic rays and caused them to operate a motive device. … I have advanced a theory of the cosmic rays and at every step of my investigations I have found it completely justified. The attractive feature of the cosmic rays is their constancy. They shower down on us throughout the whole 24 hours, and if a power plant is developed to use their power it will not require devices for storing energy as would be necessary with devices using wind, tide or sunlight. All of my investigations seem to point to the conclusion that they are small particles, each carrying so small a charge that we are justified in calling them neutrons. They move with great velocity, exceeding that of light. More than 25 years ago I began my efforts to harness the cosmic rays and I can now state that I have succeeded in operating a motive device by means of them. I will tell you in the most general way, the cosmic ray ionizes the air, setting free many charged ions and electrons. These charges are captured in a condenser [capacitor] which is made to discharge through the circuit of the motor. I have hopes of building my motor on a large scale, but circumstances have not been favorable to carrying out my plan.

                              Comment


                              • Thanks Soundiceuk!

                                Originally posted by soundiceuk View Post
                                Hi Ufopolitics, I have followed your excellent work for a while now

                                It's kind of cool how many of the threads seem to be crossing over lately.


                                I may be off the mark here but here is a research link Bruce sent out tonight and I just couldn't help but wonder what your opinion is of the patent. I'm not sure how relevant it is to your work, but if you or anyone else hasn't seen it before, you may find it interesting.



                                Priest Has Motor Run By 'Ion Energy'

                                Antonio d'Angelo -- Inter-Atomic Ion Motor -- NY Times article & US Patent # 2021177

                                http://www.rexresearch.com/angelo/us2021177.pdf



                                Also I wonder if Tesla's motor ties in too?

                                Brooklyn Eagle
                                July 10, 1932
                                Nikola Tesla States:
                                “I have harnessed the cosmic rays and caused them to operate a motive device. … I have advanced a theory of the cosmic rays and at every step of my investigations I have found it completely justified. The attractive feature of the cosmic rays is their constancy. They shower down on us throughout the whole 24 hours, and if a power plant is developed to use their power it will not require devices for storing energy as would be necessary with devices using wind, tide or sunlight. All of my investigations seem to point to the conclusion that they are small particles, each carrying so small a charge that we are justified in calling them neutrons. They move with great velocity, exceeding that of light. More than 25 years ago I began my efforts to harness the cosmic rays and I can now state that I have succeeded in operating a motive device by means of them. I will tell you in the most general way, the cosmic ray ionizes the air, setting free many charged ions and electrons. These charges are captured in a condenser [capacitor] which is made to discharge through the circuit of the motor. I have hopes of building my motor on a large scale, but circumstances have not been favorable to carrying out my plan.

                                Hello Soundiceuk!

                                And thanks!

                                That Patent sure looks very interesting...D'Angelo shows very clear wiring and windings there, nice graphics for the "Age" of that Patent!...excellent Artist!...Italian of course...LOL

                                Machines have dual commutator assemblies at different configurations (similar to mines)...However, if you "follow" the wires they leave upper commutator and then "return"to Upper Commutators next element (Lap Symmetrical Wind)...as so it happens the same way at lower commutators...it is a very similar design to the very Old Dynamo-Motor Machines...
                                Unfortunately...they are still ruled by the Symmetry...

                                But can not deny the great Magnetic Patterns that would be created by those very different concepts in windings and overlapping between upper-lower crossed coils.

                                Thanks for sharing it here!


                                Regards


                                Ufopolitics
                                Last edited by Ufopolitics; 08-23-2012, 12:18 AM.
                                Principles for the Development of a Complete Mind: Study the science of art. Study the art of science. Develop your senses- especially learn how to see. Realize that everything connects to everything else.― Leonardo da Vinci

                                Comment

                                Working...
                                X