I purchased the Bedini 8 to 52V 6 Inch Brushless
Motor Fan Full Kit at rpmgt.org
I really want to make this work.
I have no business trying to make it work because
I know NOTHING about anything.
In the video FanSSGconstruction.wmv
I'm not trying to rewind the coils; I was just looking for more info.
I see @1:30 mins, only 2 wires cut between the coils
and the circuit board, the other video states "2 wires" also.
The fan in my kit has 4 wires between:
2 single wires and 2 twisted together to the circuit board
from the coils.
Is this going to make a difference?
Is this fan able to be used, as it is, for a Bedini?
I'm a software programmer and I know it is very
hard to give idiot-proof instructions for idiots like me.
I don't want to make waves or complain.
I'd like to point out why I'm confused about a few things
and ask some questions.
Remember I can't read / understand a circuit layout or
BrushlessEnergizer1.jpg (attachment)
Points that caused Mr. Know-Nothing (me) confusion with the video
Brushles_Motor_Fan_Bedini_Energiser_Overview_And_A ssembly.wm
v
p1) stated: The statement is made there is a single wire is making up
the coils. (I don't know were in the video that was said)
This started my confusion.
A single wire means to me, I'd expect to find a single start/end pair of
wires leaving all 4 coils.
I find 4 wires soldered to the fan's circuit board.
I must conclude then:
Is there 2 single wires making up 2 coils each
to have 4 wires total exiting the coils and soldered to the
fan's circuit board?
I guessing it was meant that the coils were not double wire wound
when it was said a "single wire" was used?
P2) @16:52 "and then you'll find two other wires soldered to
the circuit."
This jives with P1, but I have 4 wires and 3 solder joints.
2 single wires and 2 twisted together, making 3 solder joints on the
fan's circuit board.
p3) @18:12 "so what you'll have is 8 wires coming off this circuit."
That statement makes me think I'll have 8 wires exiting
the fan housing.
? looking at BrushlessEnergizer1.jpg I think I only see
5 wires exiting the fan housing.
Is 5 wires exiting the fan housing correct?
With what I am seeing (wires) and what I understand at this point,
I make 4 wire cuts (top side) at each coil and cut the 4 wires off the
fan's circuit board. That would give 4 start/end pairs for each coil.
That gives 8 totals wires, is this what I need to do and is correct?
Looking at the circuit layout in BrushlessEnergizer1.jpg (BEpic)
I see only 5 wires exiting the fan housing, is this correct?
8 wires, 4 start/end pairs for each coil.
I count a total of 7 new wires added inside the fan housing,
2 connecting opposite side coils and 5 leaving the fan
Is this correct?
I have 2 MJL21194, an internet search tells me the
TIPO of MJL21194 is NPN and the P/OUT
1-2-3 is BCE. Now I know the MJL21194 is the NPN
on the diagram (BEpic).
Question: BCE (pins) are left to right with the
label MJL21194 upwards and readable, Correct?
I have 1 2N6509G, an internet search indicates, to me,
2N6509G is the item marked SCR (K,A,G) in circuit?
I've attached Questions.jpg that have a few questions
about BrushlessEnergizer1.jpg.
Many thanks ..
If I get this to work, I could document in greater detail
how someone like myself could build these.
Randy
Motor Fan Full Kit at rpmgt.org
I really want to make this work.
I have no business trying to make it work because
I know NOTHING about anything.
In the video FanSSGconstruction.wmv
I'm not trying to rewind the coils; I was just looking for more info.
I see @1:30 mins, only 2 wires cut between the coils
and the circuit board, the other video states "2 wires" also.
The fan in my kit has 4 wires between:
2 single wires and 2 twisted together to the circuit board
from the coils.
Is this going to make a difference?
Is this fan able to be used, as it is, for a Bedini?
I'm a software programmer and I know it is very
hard to give idiot-proof instructions for idiots like me.
I don't want to make waves or complain.
I'd like to point out why I'm confused about a few things
and ask some questions.
Remember I can't read / understand a circuit layout or
BrushlessEnergizer1.jpg (attachment)
Points that caused Mr. Know-Nothing (me) confusion with the video
Brushles_Motor_Fan_Bedini_Energiser_Overview_And_A ssembly.wm
v
p1) stated: The statement is made there is a single wire is making up
the coils. (I don't know were in the video that was said)
This started my confusion.
A single wire means to me, I'd expect to find a single start/end pair of
wires leaving all 4 coils.
I find 4 wires soldered to the fan's circuit board.
I must conclude then:
Is there 2 single wires making up 2 coils each
to have 4 wires total exiting the coils and soldered to the
fan's circuit board?
I guessing it was meant that the coils were not double wire wound
when it was said a "single wire" was used?
P2) @16:52 "and then you'll find two other wires soldered to
the circuit."
This jives with P1, but I have 4 wires and 3 solder joints.
2 single wires and 2 twisted together, making 3 solder joints on the
fan's circuit board.
p3) @18:12 "so what you'll have is 8 wires coming off this circuit."
That statement makes me think I'll have 8 wires exiting
the fan housing.
? looking at BrushlessEnergizer1.jpg I think I only see
5 wires exiting the fan housing.
Is 5 wires exiting the fan housing correct?
With what I am seeing (wires) and what I understand at this point,
I make 4 wire cuts (top side) at each coil and cut the 4 wires off the
fan's circuit board. That would give 4 start/end pairs for each coil.
That gives 8 totals wires, is this what I need to do and is correct?
Looking at the circuit layout in BrushlessEnergizer1.jpg (BEpic)
I see only 5 wires exiting the fan housing, is this correct?
8 wires, 4 start/end pairs for each coil.
I count a total of 7 new wires added inside the fan housing,
2 connecting opposite side coils and 5 leaving the fan
Is this correct?
I have 2 MJL21194, an internet search tells me the
TIPO of MJL21194 is NPN and the P/OUT
1-2-3 is BCE. Now I know the MJL21194 is the NPN
on the diagram (BEpic).
Question: BCE (pins) are left to right with the
label MJL21194 upwards and readable, Correct?
I have 1 2N6509G, an internet search indicates, to me,
2N6509G is the item marked SCR (K,A,G) in circuit?
I've attached Questions.jpg that have a few questions
about BrushlessEnergizer1.jpg.
Many thanks ..
If I get this to work, I could document in greater detail
how someone like myself could build these.
Randy
Comment