Announcement

Collapse
No announcement yet.

Bedini Solid State Oscillators

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Originally posted by theremart View Post
    80V spikes at 1 1/2 milla seconds ( the setting of one on the scope ) I am still learning how to use the scope correctly.

    It seems from looking at the r-charge site they do about 16 cycles to get the energy up to full amount for load. Perhaps that is what I am missing... but to compare a test that I had done before with the battery it seems it is getting worse for wear, not better. What I am missing from the book is the input voltage and the time range to get the desired result of charging two batteries at once that will handle a load.
    1.5ms should be ok , its 0.665khz. Maybe your coil is too big and didnt get the time to build a strong field ? (just a idea). Try to set the frequency under 400hz if you want to test my idea, the result should be better at lower frequency.


    Best Regards,
    Eric

    Comment


    • RE: Coil.

      Originally posted by EgmQC View Post
      1.5ms should be ok , its 0.665khz. Maybe your coil is too big and didnt get the time to build a strong field ? (just a idea). Try to set the frequency under 400hz if you want to test my idea, the result should be better at lower frequency.


      Best Regards,
      Eric
      You may have a point there, my coil is 20 gauge wire, and it is a full spool 3 twisted pairs.

      Think I will order some guage recommended by the book, but I don't know how much to order for 350 turns? How many feet is that?
      See my experiments here...
      http://www.youtube.com/marthale7

      You do not have to prove something for it to be true. However, you do have to prove something for others to believe it true.

      Comment


      • Originally posted by theremart View Post
        You may have a point there, my coil is 20 gauge wire, and it is a full spool 3 twisted pairs.

        Think I will order some guage recommended by the book, but I don't know how much to order for 350 turns? How many feet is that?
        Hi Theremart,

        look at this site, it give the lbs per feets for different gauge.
        Magnet Wire

        Best Regards,
        Eric

        Edit: Its about 190 feet if i remember for 350 turn.
        Last edited by EgmQC; 09-15-2008, 05:11 PM.

        Comment


        • Update on Solid State Bedini

          Well,

          I replaced both the opto, and the 555 timer, and I learned a couple of tricks.

          Put a nite light to the capacitor, this helps to diminish the 100V + charge that is stored there. I don't like discharging that the hard way ! This also allows you to see visually the amount of electricity the circuit is outputing.


          I swapped the coil for the 450 turn one, and after getting this, it is now staying at 25-27 V in the cap over the charge battery. It seems to be doing MUCH better. I believe I had miss wired my 555 timer before because I had the pin numbering wrong. ( So much fun remembering the order of the pins when you turn it upside down ) I ended up making a diagrahm of both the pins up right and upside down which help me sort out the pin much easier.

          Charging up another battery now, look forward to see if the load tests does any better.

          Mart
          See my experiments here...
          http://www.youtube.com/marthale7

          You do not have to prove something for it to be true. However, you do have to prove something for others to believe it true.

          Comment


          • Originally posted by theremart View Post
            Well,

            I replaced both the opto, and the 555 timer, and I learned a couple of tricks.

            Put a nite light to the capacitor, this helps to diminish the 100V + charge that is stored there. I don't like discharging that the hard way ! This also allows you to see visually the amount of electricity the circuit is outputing.


            I swapped the coil for the 450 turn one, and after getting this, it is now staying at 25-27 V in the cap over the charge battery. It seems to be doing MUCH better. I believe I had miss wired my 555 timer before because I had the pin numbering wrong. ( So much fun remembering the order of the pins when you turn it upside down ) I ended up making a diagrahm of both the pins up right and upside down which help me sort out the pin much easier.

            Charging up another battery now, look forward to see if the load tests does any better.

            Mart
            Hi Mart,

            Whats the volt rating of your cap ? im scared a bit to try the 555 setup, i have some 60v 30000uf but i dont know what can happen if hooked to the SS SSG with more than 200V spike.

            Best Regards,
            Eric

            Comment


            • RE: Voltage

              Originally posted by EgmQC View Post
              Hi Mart,

              Whats the volt rating of your cap ? im scared a bit to try the 555 setup, i have some 60v 30000uf but i dont know what can happen if hooked to the SS SSG with more than 200V spike.

              Best Regards,
              Eric
              500V 330 Uf, the one specified in the book.

              I believe I now have the exact Bedini setup, may need tuned now.
              Last edited by theremart; 09-27-2008, 07:35 PM.
              See my experiments here...
              http://www.youtube.com/marthale7

              You do not have to prove something for it to be true. However, you do have to prove something for others to believe it true.

              Comment


              • Originally posted by EgmQC View Post
                Hi Mart,

                Whats the volt rating of your cap ? im scared a bit to try the 555 setup, i have some 60v 30000uf but i dont know what can happen if hooked to the SS SSG with more than 200V spike.

                Best Regards,
                Eric
                as long as you start with rather fast cap dumping (around every second) a 30,000uf 60v cap shouldn't be in any danger from a standard sized SSG.

                but as a precaution just in case the cap pulser isn't working properly you can put a neon across the terminals and it should prevent the cap getting dangerously over 60v. I have had 40,000uf caps rated at 60v "accidentally" charge over a hundred and they stayed in one peice. Though I can't gaurentee that every capacitor can withstand being charged so high over their rated voltage.

                To begin with, try putting a bulb in series with the charging battery just to be sure it is pulsing and carefully watch the voltage! With 30,00uf you should have plenty of time to react if it is obvious that the pulser is not operating.
                "Theory guides. Experiment decides."

                “I do not think there is any thrill that can go through the human heart like that felt by the inventor as he sees some creation of the brain unfolding to success... Such emotions make a man forget food, sleep, friends, love, everything.”
                Nikola Tesla

                Comment


                • Originally posted by Sephiroth View Post
                  as long as you start with rather fast cap dumping (around every second) a 30,000uf 60v cap shouldn't be in any danger from a standard sized SSG.

                  but as a precaution just in case the cap pulser isn't working properly you can put a neon across the terminals and it should prevent the cap getting dangerously over 60v. I have had 40,000uf caps rated at 60v "accidentally" charge over a hundred and they stayed in one peice. Though I can't gaurentee that every capacitor can withstand being charged so high over their rated voltage.

                  To begin with, try putting a bulb in series with the charging battery just to be sure it is pulsing and carefully watch the voltage! With 30,00uf you should have plenty of time to react if it is obvious that the pulser is not operating.
                  Thank Sephiroth for your advice. I have a 6.5KV 0.25uF Laser pulse cap, should it be better or higher capacitance cap is better ?

                  Best Regards,
                  Eric

                  Comment


                  • Hi Eric,

                    Every experiment I have done with a cap pulser has shown far better results with high capacity caps pulsed at low voltage.

                    This thread goes into some interesting theory/math on cap pulsing

                    http://www.energeticforum.com/renewa...-violated.html
                    "Theory guides. Experiment decides."

                    “I do not think there is any thrill that can go through the human heart like that felt by the inventor as he sees some creation of the brain unfolding to success... Such emotions make a man forget food, sleep, friends, love, everything.”
                    Nikola Tesla

                    Comment


                    • Hi All,

                      I have a nice question, When the SSG send directly the radiant to the battery, the battery will transform it to usuable energy(by getting it from the vacuum) . With a capacitor setup, the radiant spike is sent to the cap and then the battery.

                      My question is, What is inside the capacitor ?

                      if we see for exemple 16 volt on a 30000uf cap before it dump it to the battery, that mean there 3.84 joules sent to the battery.

                      There's radiant in the cap or its transformed already in usuable energy by the capacitor? if he is already transfomed that mean we only have to feed a cap at 16v and dump at X Frequency to get the same effect?

                      Best Regards,
                      Eric

                      Comment


                      • Ok test results again very poor

                        Results of load test attached

                        Green -> results of charging battery with neo for 6 hours. 3.2 amp hours

                        Red -> Results of first SS test .5 amp hour

                        Black -> Charged battery up to 15.34V with Solid state Bedini as per book as stated. then discharged. only 1 amp hour


                        Last edited by theremart; 09-29-2008, 02:20 PM.
                        See my experiments here...
                        http://www.youtube.com/marthale7

                        You do not have to prove something for it to be true. However, you do have to prove something for others to believe it true.

                        Comment


                        • Hi Mart,

                          Those results don't look optimistic.

                          How long did you leave the battery to rest before doing the load tests?

                          How high were you charging the cap above the charging voltage?
                          "Theory guides. Experiment decides."

                          “I do not think there is any thrill that can go through the human heart like that felt by the inventor as he sees some creation of the brain unfolding to success... Such emotions make a man forget food, sleep, friends, love, everything.”
                          Nikola Tesla

                          Comment


                          • Re: results

                            Originally posted by Sephiroth View Post
                            Hi Mart,

                            Those results don't look optimistic.

                            How long did you leave the battery to rest before doing the load tests?

                            How high were you charging the cap above the charging voltage?
                            I left the battery on for over 12 hours on the newly configured solid state charger. Input of 12V at .8 amp. for charge.

                            Then it rested for about 6 hours. Since I wanted to do a test in the morning I then again put it on the SS charge at 8V at .5 amp for 12 hours so it was at 15.34 in the morning I ran the load test.

                            The charge in the cap is 25V. Not optimal for fastest charge, but should be enough to give me punch out of the battery I would think.


                            I am now charging the battery again with my ssg with neo's to get another idea of where the battery is.
                            See my experiments here...
                            http://www.youtube.com/marthale7

                            You do not have to prove something for it to be true. However, you do have to prove something for others to believe it true.

                            Comment


                            • Do you have any larger caps you can substitute your 330uf for?
                              "Theory guides. Experiment decides."

                              “I do not think there is any thrill that can go through the human heart like that felt by the inventor as he sees some creation of the brain unfolding to success... Such emotions make a man forget food, sleep, friends, love, everything.”
                              Nikola Tesla

                              Comment


                              • RE: cap

                                Originally posted by Sephiroth View Post
                                Do you have any larger caps you can substitute your 330uf for?
                                I don't, but I will be VERY VERY ticked if the cap specified by the book is the wrong one! I was told not to modify any of the circuits of the book. that they work as is!
                                See my experiments here...
                                http://www.youtube.com/marthale7

                                You do not have to prove something for it to be true. However, you do have to prove something for others to believe it true.

                                Comment

                                Working...
                                X