One magnet no bearing Bedini motor

[Lidmotor]

Everybody---WELCOME to the party

I can get the same effect with the sg and clf back the the power battery with one wire charging a cap in parral to the battery, again i cant see if the draw is lower But i have no HV around the setup.
I have two videos uploading of the earth battery charging a cap with single wire, this is free energy that needs a switch to get the true potenial out of it.

Hi Bodkins and Gadget----Welcome to Jonny's party! He has a good one going on here. With all these brillant minds at work here we will have the Earth's energy problems solved in just a few days.

@ Bill---I am with you about where the free energy comes from----I don't care. I'll take it from the earth, the sun, the wind, or EMF out of the air. If it makes our life easier then who cares.

@Xenomorph & Comwarrior---- The circuit that I am now using loops the BEMF. Right or wrong it seems to work just like you guys found out. It makes for a very low amp draw. The one wire charging is something that I worked with on the Dr. Stiffler's SEC project. It is the AV plug idea. Slayer007 and I played around with it

@Retrod---Dave I really like the idea of using a signal generator to run this. It would really add alot more control. The question is: How is that degaussing coil wound?

[Xenomorph]

@All:

According to this: http://www.staffordnet.net/degausscoil.htm

and a couple of other DIY forums, degaussing coils are made of
AWG 22-24 wire wound 400-500 turns.
I guess Retrod1 would have to damage his coil to be able to have a look and verify the gauge.
Its obiously the big flux area that generates the high voltage rather than the high turn count in much smaller coils.
The window motor coil is actually doing the same thing.

[Bodkins]

we have crack it!
YouTube - earth battery singlewire1

uploading next video and going to bed!! in the next video i say 8 volt but its 0.8 volts. but thats not the point, the fact if fills with no input,it opens the door for all the great work here to be build together all over the world, with mother earth at the root

[JohnnBlade]

Substitute for pyrolytic graphite

Hi All,

Does anone maybe know a substitute for pyrolytic graphite
with that we could make our sphere/magnet levitate.

today i have been testin magnets spinning ontop of my levitron donut magnet, but not enough to make it levitate, or atleast the RPM are no enough.

@JohnnDavro, LidMotor, XenoMorph, Retrod, You, is it possible for you to test your rotor magnet with a small thick piece of copper, or aluminimum foile on it, and then place/drop a tiny sphere, or magnet on top of it, cause it looks like you got lots of RPM's
to see if it could levitate or maybe see what FX it has on the magnet.

and something i dont understand, why doesnt my sphere turn and stick to the center of the levitron donut magnet
while i gues south is center, and north out or other way arround, normally the sphere should turn arround and stick to the right pole, but it does not, and starts to levitate
but you would need a wall to keep the sphere from moving, i used a small container
and since the sphere is round it should turn and stick to the right pole right, with enough space for the sphere to turn in the container

hope this is a bit clear

Greets JB

[JohnnBlade]

levitation rotor

Hi All, (again)


i saw this vid on Youtube, by YouTube - cyberelectronics's Channel

YouTube - Homemade Electronic Levitron

whereby the magnet levitates using an electro magnet.

this is the same im trying to do,but then Bedini style

Greets JB

[JohnnBlade]

Could this be something for the rotor - Helmholtz Coil

Helmholtz-Spule – Wikipedia

its to make a levitron top spin, with a coil
YouTube - endless Levitron

Greets JB

ps: Michael Jackson just died FYI, while posting this, watch CNN

[retrod]

Hi All,

Does anone maybe know a substitute for pyrolytic graphite
with that we could make our sphere/magnet levitate.

today i have been testin magnets spinning ontop of my levitron donut magnet, but not enough to make it levitate, or atleast the RPM are no enough.

@JohnnDavro, LidMotor, XenoMorph, Retrod, You, is it possible for you to test your rotor magnet with a small thick piece of copper, or aluminimum foile on it, and then place/drop a tiny sphere, or magnet on top of it, cause it looks like you got lots of RPM's
to see if it could levitate or maybe see what FX it has on the magnet.

and something i dont understand, why doesnt my sphere turn and stick to the center of the levitron donut magnet
while i gues south is center, and north out or other way arround, normally the sphere should turn arround and stick to the right pole, but it does not, and starts to levitate
but you would need a wall to keep the sphere from moving, i used a small container
and since the sphere is round it should turn and stick to the right pole right, with enough space for the sphere to turn in the container

hope this is a bit clear

Greets JB

Hi Jb,
I haven't been able to spin any magnet on top of aluminum, far too much drag. Pyrolytic graphite is the best material to try. Bismuth, will not work as well but certainly worth a try.

Good luck,
Dave

[fusionchip]

My OU Davro Bedini !!!!!!!!!!!

YouTube - jonnydavroreplication
all . i know you all will not believe this but i have got that unit to selfcharge and run feeding back the secondary to the primary and the primary is climbing .I kid you not . This is the third self running bedini it looks like . Ok i ditched th e2.6 volts this morning and hooked up the 6 volt sla battery as the primary and 2.6 volt as the secondary . the 6 volt was a bad battery and read 5.99 volts . I decided to try My feedback method that works on My other 48 volt fan bedini . the only modification i did was remove the secondary batter install an sk3606 in series with one secondary wire the one that comes from the positive off the secondary cap and anode of the diode and fed it thru the sk3606 to positive where the run connection is . now the primary battery is reading 6.52 and climbing as it is running the egg. WOW . i'lll let you know more later after 9 est as i have to take my daughter to bible school .I had to do a wuick test before i go . i stopped the magnet and the volts are reading 5.38 just as soon as i start the magnet it jumps to over 6.65 and then settled to 6.52 -6.53 Amazing stuff.


Yep its Defiantly Charging the primary . this is my Third one . Feedback to source from the secondary with aslight modification of MINe .@a video showing this replication with the addition and showing you what i mean . Its not a trick and i'm not showing you anything tricky as i never do . It does what it does all day today .It now up a few more volts .
This was a dead Sla three days ago .this is the one iwas using as a secondary and trying to recondition as it would not charge up over 3 volts with a NOrmal Charger . After 3 days this battery settled this morning (6am) at 5.99 steady so ooo. after all day long selfcharging it got HIGHER AND HIGHER and still ran . I'll give it a few more days before i pop the cork . I want to capture the relay coil power and charge another battery OR run a JT Led circuit.
been a busy day . i made the video at 7 pm and got back from Bible school at 10 . the battery is up to 6.56 at 10:05 WOW. Normally the battery would rise gradually in volts when you disconnect a circuit but this half dead /restored one Drops .and then fires back up .Remember I am using caps on the secondary thus they are changing the BEMF Volts to Current so there is a Push Now and not real Static Volts any longer . what you think Guys . I'm dead tired and copied most of my words from the OU forum . I am very tired but again excited that the sk3606 has done it again.
Edit *** this Morning the volts are 6.65 Im going to doa cap test starting around 10 est Friday 26 2009.
Gadget
aka fusionchip

[Bodkins]

YouTube - earth battery singlewire2 sorry for the posting this in two places but i think its important to understand, once i have got this running with the sg i will build the davro master piece of power

[jonnydavro]

@Fusionchip.WOW Al.This is exactly why i was so pleased that you never gave up on the build and i was hoping you would try your mods.I have just looked at your vid and it is looking good and the way the battery climbs up when you connect the feedback is quite remarkable.To go from 5.99v to 6.52v shows you have something here so feel free to post your circuit as i think there will be a few who wish to replicate,including myself.
Please include all details and tips you feel are needed for a successful rep.
Thanks for sharing your success with us Al and let us know how your further tests go.Regards jonny

@Bodkins.Hi..Pirate has run a OMNBB on his earth battery but i think he was getting 2v out of his but he has a very large chunk of magnesium buried and some nice carbon rods so this may explain the voltage difference.If you could connect a few EB's this may get your voltage up,but Bill said this was hard to do but you may have more luck.Thanks for posting and we look forward to seeing you run a motor of it.Nice one.Regards jonny

[retrod]

@All:

According to this: http://www.staffordnet.net/degausscoil.htm

and a couple of other DIY forums, degaussing coils are made of
AWG 22-24 wire wound 400-500 turns.
I guess Retrod1 would have to damage his coil to be able to have a look and verify the gauge.
Its obiously the big flux area that generates the high voltage rather than the high turn count in much smaller coils.
The window motor coil is actually doing the same thing.

@Xenomorph,
I ordered a coil that looks the same (externally) as my old one. When it gets here I can compare them. Because the resistance of the old coil is so high (300 ohms) I suspect smaller wire then AWG 22-24, or a resistor in series internally.
More coil info: YouTube - Sphere Magnet Spinning with Degaussing coil & function generator. Part (2)

Dave

[fusionchip]

Gadget mod to Jonnydavro Feedback to source /simple

here is a rough schematic . Maybe jesus can clean it up . Its My selfcharger /runner Modification of the Jonnydavro circuit . for test only but mine appears to be WORKING !!!!!!Im a little delayed with caps making some measurments and junk . I noticed that ther is an ac component and it reads 13 volts on the ac scale so its still pulsed dc hitting the battery . I accdently shorted the battery and it dropped to 5 . 8 volts but recovered slightly . as soon as i gave it a spin its back up to 6 . 65 .. more test . i have to disconnect those ultracaps from my Earthbattery setup and have to make measurements and stuff on them first . doing research for Advanced Research systems in the Black mountains for Greg On Earth Batteries .
Gadget

[Bodkins]

hi Jonny its not about the volts from the ground its about the singlewire negative charging a cap to ground, connect the diodes to your onemagnet source battery negative and because your are switching the power on and off it will suck up energy from the ground and charge the cap.
here Im only talking about the negative ground more to come
good luck all, great work
looking good Fusionchip

[Xenomorph]

@Bodkins:

Do you mean like that? Without actually connecting the earth wire?

[Bodkins]

@Xenomorph Yes now connect the ground to the negative of the cap.it will fill up
if you have a second ground of metal zinc/galivized steel or like Bill magnesium.(i have copper carbon=postive, and steel galivized with lime=negative)
the potencial difference of the limestone dust and carcoal carbon is key like Bill carbon to magnesium same thing,the difference is all we need!to get energy.

now Xenomorph you will see the cap rise but thats only one ground the other can go on the postive of the power battery with diode, so your discharging to ground passing the cap and suctiing energy into the cap AND pulling energy in to the postive of the battery too. try it with a cap on the front end?
goodluck


ps what i did with clf is put the cap postive to the postive of the power battery with a diode, will do a video if i get time