Bedini Ferris Wheel Regauging Motor

[John_K]

Hi everybody,
What is prove useful the Bendini machine ? Only, is it charger machine or what ?
can someone explain to me ?

You should probably read the thread from the start to find out.


John K.

[antony27]

Hi,
I read this thread but i dont understand that "why not john bendini is the richest man of the world" ?

[Redisnoc]

"why not john bendini is the richest man of the world" ?

"why not john bendini is the richest man of the world" ?

He should be, just from "surround sound" that was stolen from him.
He might be, from the patents that seem to be close to taking off.
Remember, there is no profit in "free", so TPTB (the powers that be) are not happy to think their products could become (nuclear poison, black poison/coal and oil) worthless.
They would not be happy campers...
short answer
Dave Luke

[stonewater]

ha ha ha....No worries on the wire... Just get us all some free power.....!
Speaking of which, Have you been thinking about how to capture those scalers off the 3GT?


Les

I saw a true "pancake coil" once set at right angles to an SG..... its a scalar wave antenna. Rick F had one wound, saw it at the sandpointe conference. I think it is the only coil that can capture them.

[BrentA929]

Barrium Ferrite Magnets

@All,

Just wanted to give everyone an update on the magnets I found...

It boils down to a quantity thing for it to make any since. If we can get (10) people that are interested then I can get the magnets for around $38/each. That would be the pie shaped (dimensions to be confirmed) barium ferrite magnets shipped to the DFW area. From there it would all depend on who was interested. The largest cost is in the tooling for the shape. We could greatly reduce that if anyone knows where we can get them cut. I have asked a few people and they won't do it here in the States because barium is considered toxic (hazardous material).

Let me know your thoughts!


Thanks, Brent

P.S. I am excited about the conference and hope it clears up some of the questions that we all have...see y'all there!

[Rl2003]

[QUOTE=BrentA929;147310]@All,

Just wanted to give everyone an update on the magnets I found...

It boils down to a quantity thing for it to make any since. If we can get (10) people that are interested then I can get the magnets for around $38/each. That would be the pie shaped (dimensions to be confirmed) barium ferrite magnets shipped to the DFW area. From there it would all depend on who was interested. The largest cost is in the tooling for the shape. We could greatly reduce that if anyone knows where we can get them cut. I have asked a few people and they won't do it here in the States because barium is considered toxic (hazardous material).

Let me know your thoughts!

Hey Brent,

Put me on your list.
I will be unable to attend this conf. and can only imagine that this one will be even more exciting than the Nov. conf.
It's a time conflict with other obligations that came first.
Please keep us updated to anything new, you may pick-up, for things concerning this project.
I am sure John has a few things that will
be of great interest to those of us who jumped into this endevor.

Thanks, Mark P.

[Rl2003]

The quiet before the storm?

This thread has been very quiet. Every one must be packing
for the Conf. I have been trying a few different variations of
circuits to back charge the Primary batteries while they are not
loaded. I was able to see an slight increase in voltage when I manually
switched and dumped a cap back to the prim. batteries, but when I
set up a switch for once per rotation. No luck. I believe I need to wait longer
to dump the cap at a higher voltage and get it as close to the off time
of the master coil as possible. (any ideas) I tried the Mosfet circuit some one posted
awhile back, but haven't been able to see any positive results from that yet.
I feel that I am close, even without the fly wheel effect you will have with
a heavy wheel, and still hopefull something will work here.
Mark

[albertMunich]

I wish all of you who will attend a great time at the conference. I am across the planet but look forward to hear and see what went on there. Lets see what they have up their sleeves this time. Perhaps they will disclose their theory behind the operation of the ferris wheel.

Good luck to all of you

Albert

[John_K]

Bfw

I wish all of you who will attend a great time at the conference. I am across the planet but look forward to hear and see what went on there. Lets see what they have up their sleeves this time. Perhaps they will disclose their theory behind the operation of the ferris wheel.

Good luck to all of you

Albert

Hi Albert,

Yes, John B showed the cicuits for the Ferris Wheel and people could come up and photograph them and the scope shots. Some people here were very close to what John B had used.

People were not allowed to video the session under instructions from John B (the rest of the conference could be filmed though), so you'll have to wait for DVD#28 if you weren't there.


John K.

[Les_K]

Conference

That was quite a conference, it was great to meet so many people
And chat about what we learned. It was very impressive to see ricks
machines running. The pictures just don't do them justice, smooth .... Wow!
John_k I sure would like to have talked more, and yes I got my answers so
My wife says were not in trouble.....

I still don't know how to tune my machine as I don't know how john
Went about it but to see the physical evidence of order vs disorder or
entropy compared to negentropy by the main coil being cold and
the other hot was to say the least impressive.

Les

[Web000x]

I still don't know how to tune my machine as I don't know how john
Went about it but to see the physical evidence of order vs disorder or
entropy compared to negentropy by the main coil being cold and
the other hot was to say the least impressive.

Les

I would have felt that there was some significance to the temperature difference if the coils had been the same impedance, but they were clearly far out of range of each other to show that this was anything different.

Of course the small coil was warm, it didn't have an iron core and it was 1/4 the size of the main coil. Lower inductance and lower resistance is going to cause more heating.

I know that you and I spoke about this Les, but I am just posting it to bring attention to this to everyone else that may not have thought about this.

I am not claiming that John Bedini is wrong, but I would have liked to see some sort of control in that experiment.

Dave

[John_Bedini]

I would have felt that there was some significance to the temperature difference if the coils had been the same impedance, but they were clearly far out of range of each other to show that this was anything different.

Of course the small coil was warm, it didn't have an iron core and it was 1/4 the size of the main coil. Lower inductance and lower resistance is going to cause more heating.

I know that you and I spoke about this Les, but I am just posting it to bring attention to this to everyone else that may not have thought about this.

I am not claiming that John Bedini is wrong, but I would have liked to see some sort of control in that experiment.

Dave

Web000x,

This is John K. I'm sitting at John B's computer in his shop because I can't login on my computer. I'm here working on something in his shop.

You must have been the one that was sleeping in the second row!

John B explained very clearly that the second coil was to tune the machine. He even held the microphone out to the crowd and asked if anyone had any questions.

I measured the coils on Eric's machine. The big main coil was 2.0 ohms, 3 windings of different wire gauge in parallel. The tuning coil (the air coil) measured 2.0 ohms, single winding. Both coils in parallel meaured 1.0 ohms.

Both coils are EXACTLY the same in impedance and inductance!! How can one coil be cold and the other warm in when they are both the same?

It was a way to show how to tune the machine, to get the energy out.

John B's wagon wheel machine was exactly the same with the tuning coil.

John B explained this to everybody and told you how to get the energy out of the machine. If you missed it, you must have been sleeping. Lucky for you you can see it again when the DVD comes out.



John K.

[Web000x]

Web000x,

This is John K. I'm sitting at John B's computer in his shop because I can't login on my computer. I'm here working on something in his shop.

You must have been the one that was sleeping in the second row!

John B explained very clearly that the second coil was to tune the machine. He even held the microphone out to the crowd and asked if anyone had any questions.

I measured the coils on Eric's machine. The big main coil was 2.0 ohms, 3 windings of different wire gauge in parallel. The tuning coil (the air coil) measured 2.0 ohms, single winding. Both coils in parallel meaured 1.0 ohms.

Both coils are EXACTLY the same in impedance and inductance!! How can one coil be cold and the other warm in when they are both the same?

It was a way to show how to tune the machine, to get the energy out.

John B's wagon wheel machine was exactly the same with the tuning coil.

John B explained this to everybody and told you how to get the energy out of the machine. If you missed it, you must have been sleeping. Lucky for you you can see it again when the DVD comes out.



John K.

I was not sleeping. I heard John say that was how he tuned the machine, but I never heard John mention the exact impedance of those coils.

Just curious, what were the inductances of each coil?

Thanks,

Dave

[BrentA929]

Conference

Hey guys,

It was great to meet everyone and be able to put a face with all the screen names...

I really enjoyed the conference and wanted to thank John B and others that made this all possible. The conference was a definite reminder of how little I know about this technology, but am eager to get back to work on our six foot wheel!

Since we are talking about the tuning coil I will ask a question...which coil is considered the tuning coil in the three coil setup? Is it in the main coil? Is it one or both of the slave coils?

Excited that the thread is back up and running!


Thanks, Brent

[John_Bedini]

Bedini GT3

Dave,
It was not only explained to you the number of turns was written on the coil and the impedance too.
I also said to everybody if you can not make the circuits I would supply them if the response was good. The two machines were tuned different because of the build, the difference between the two machines. I have never seen any of your builds. Do you plan on building something or is john just spinning his wheels here?.

I think it was understood how I run my lectures I do not leave anything out. You were also allowed to view the machine running take still pictures and ask any questions.

The only answer I received about the free part of the energy came from Peter L after waiting 45 seconds for the group to answer. Everybody was told where it was and how you get it along with the recovery process. You were also shown how to make a semiconductor battery and a oscillator to use as power or recovery to charge batteries, that was free for the taking, Chuck H, was also running a 30 pound window motor off those cells. To bad that nobody reported what was explained to them, but it was more technical the you have reported early on. and yes it also covered sales, it's the only way I know how to eat.
John B