Stanley meyer the true

[sebosfato]

The injectors in direct injection configuration is needed to make safe operation and to lower what stan calls the speed of the gas explosion and works like this:

In the intake phase the motor let the air get inside of the motor than the motor start the compressional stage the air get up to 600 degree and when the piston start to going down again the hydrogen and oxygen is injected causing a controlled explosion. You wont need any spark. What Stanley call the laser distributor is in fact a common distributor witch is just used to turn on and of the solenoid in sync with motor turning, that control the hydrogen injection and at the same time it make the signal for the duty cycle witch control the power output.

The non combustion gases serves not only to lower the gas explosion speed but to act as a flash back arrestor in conjunction with the quenching circuit. This is the only way to inject hydrogen and oxygen together. Note Pure hydrogen wont explode until it has at least 4% of oxygen. The mixture also causes the temperature of the flame to be lower and the minimum temperature for to it self explode to be higher.

[sebosfato]

my gift for you guys however help if you can donating or requesting me to construct a pll circuit for you...

[sebosfato]

YouTube - 24102009001

[chasson321]

Image Change

last edit....

[sebosfato]

you r right chasson

Anyway when he talk about image charge he is very very generalist and almost everyone says oh image charge here and there... I just made his comment to make you notice that maybe you should go over image charges and study real electric fields ( mister van de graff) like i indicated to all of you one million times.

Inside a sphere there wont be a charge nothing imaginary just like it happens

so every time you put a charge inside the sphere or cylinder you will charge it because will always be there a differential of potential. (obviously until you have corona discharges)

This might be the only thing h20 talks about but he is not clear maybe because he don't want to be clear or probably is not clear even to him self, however i sincerely hope him or you or another one to finish the project.

I'm almost done. And the fact that i see you all are too far from me makes me sad about the misinformation.

Good luck for you all

[Aaron]

video

YouTube - 24102009001

Are you able to repost this vid?

[sebosfato]

Are you able to repost this vid?

Yes aron this video i show the resonant circuit that turns on and of and you see it goes directly in resonance.


YouTube - sebosfato's Channel

[tpuman]

Hi sebas,

I read your thread and found intersting. I have questions regarding a TPU from Steven Marks video since 2006. Do you have any clues or circuit that i could buy or donate to you? You seems to have answers and a knowledgeable guy.
I think maybe 2 or 3 people has something but keep it secret. Example:

Re: IST! NEO ZAP! TECK Breakthrough ....
« Reply #246 on: May 08, 2010, 08:15:35 PM »

im sorry this is best understood useing a MOT ...

ie it is a inductive inballance wich fills the caps SOOOOO HIGH SOOOOO FAST FOR SOOOOOOO LITTLE ....

GET A MOT ...

TO FURTHER UNDERSTAND !

ist!

How do you think about that: Inductive imbalance............


the TPU stuff is all about bad science or something worth to find ????

[SuperCaviTationIstic]

Regarding MicrowaveOvenTransformers and electrolysis.....

I was thinking, why not make the core of a coil also it's capacitor. It seems like this is what a MOT does, but only on one pole. Why not have a nice bifilar coil just like TESLA's patent for an electromagent on one side of a stainless steel plate, with the end of the wire connected electrically to the plate. Do 2 of these, one connected to positive and 1 to negative.... (I'm also thinking the bucking fields MEYER indicated in some of his patents for the VIC could be built right in, just wind the 2 coils in opposite directions!)

[sebosfato]

hi guys

I have tryed mots for a while and they can put lot of power out when using low frequency 220 v on the primary... But i have not seeing any ou with it...

About the TPU i believe that somehow it has to do with steorn solid state device principle but i'm not sure. (electro magnetic interaction they talk about)

I think that is possible that they use a coil that saturate the core and other that they input the current without bemf than they turn of the first saturating pulse... thus having the inductance of the 2 coil greater than was during the saturating pulse. Creating an inductance gain or something like that... again not yet too sure on it and how much useable could it be...

I'm still working on a new prototype but is very very expensive. So i'm trying to put the money together with some friends because we were not to much lucky to find investors with good intentions. However I can tell you, everything i posted here was related to resonance and with this info you can actually understand what resonance really is. This were my propose.

I'm getting into a point were i'm seeing that only way to produce too much h2 from water is very expensive. The diodes needed cost me for the next prototype more than 6000 euros. This is only for the diodes! (other materials will cost 3 times this) Than we have the cost for the soldering ...
The resonant capacitor will cost me only for the materials polipropilene and copper bars and thin copper paper will cost me about 600

This will handle 10000 amps at about 5kv 20khz

I'm finding that the production might be dependent on simply voltage (current and capacitance dependent) and frequency and the energy consume is dependent on the current.

Need to go sleep now, tomorrow i write more and will have more time to look after this inductive imbalance you say as to be able to tell what i think about . ok

Regards

[tpuman]

Thank you sebos for you opinion about it,

I did some very basic electrolysis in the past but i lost interest on it (especially if you live in winter season like in Canada!) until i saw the video of TPU and everything related to earth magnetic.

How is it impossible to not tap this natural flux like the flow of a river? like Steven asked himself?

The inductive imbalance might explain or the inrush current are very strange behaviors that need to further investigate. I could explain on the inrush current but if it still relate to earth magnetic than we might have something here. If not the quest is in vain and go directly to bad science.


I will post an interesting links about my guess on the TPU stuff. I follow and think very few of them found it but still unable to really explain the operation nor make it seft-running. The last point is very important and also the over heat issues by Steven Marks. I found the Meyer circuit as simple resonant circuit(even as the Joule thieft as is simplest form) related to TPU search, they are related somehow and depend on the application you do with it.

The Meyer circuit and JT are a DC pulsed circuitry,therefore an oscillation circuit. The questions about overcome of loss to make it over unity.

I always want to find and make things simple as possible by any means.

thanks for replies

[sebosfato]

I tryed to look for the inductive imbalance but only found that it is a problem that happens on three phase electric motors or something like shorted turn on transformers.. witch lead to destruction of the device or lower inductance and deficient efficiency ...

I would like to correct my words

I wanted to say
Production (h2) would depend on frequency because as frequency is higher the current will be higher too, and the interactions rate will be higher. Voltage is the rate of current per capacitance unit ... but having an external resonant capacitor that have a 5kv limit, limits you to need to higher the frequency if you want higher current. However due to inductive reactance and limitations of diode prices the ideal would be not so high frequency as to allow a smaller voltage as it results in resonant circuit from current*reactance and as such the higher capacitance possible...
However this is the only info i can tell because of problems we have here. anyway for me is important to make this min info available...

Switch of the covalent bound is the real secret. It has to do with force equation due to density of charge and things i mentioned on my posts. Please don't ask. If you are interested is easy to find all my posts...

There is a quite interesting theory, being discussed about bitoroid patent... i believe that is one way to understand over unity... at least i guess i understood.. .

I would like to construct a device to check if that really work too ( bi toroid ) but have no money to do so too. =( however one day things will change.. hopefully

Regards
Fabio

[SuperCaviTationIstic]

watch out for the bi toroid bucking coil, it is a wormhole generator! make sure you understand all things associated with this technology before you use it...

Magnetic vortex wormhole generator - Google Patent Search

[sebosfato]

MaN John Quincy St.Clair is completely mad scientist.

I have a very old friend and partner that i'm working with, witch is a mathematician and physicist that talk about things like the one seeing in John Quincy St.Clair patents.

Wow, everyday for me is more clear that we will get there. Unfortunately i have no money, otherwise this kind of tech would be already done and working.

He told me that we will construct it but that for my own safety he will build the black magic box alone. I just need to find money...


Thanks you made my day much better even if i could not sleep all night, reading all the patents.

[SuperCaviTationIstic]

I knew these patents were legit the second I saw them.....I guess I have a real reason to build a Rodin Coil now..... Marko's design is way better for the toroidal windings