Separator cell from HHO-research.com.au build by thedude

[thedude]

he dude

thanks for reacting

I just wanted to proof that you can make hydrogen without any substance in it

no KOH or whatever else

and throughout history it seems that back in the midieval times

they did it with hy voltage sinds there was nothing else

so I wanted to check the efficientie from it and find out

that this way is also not the right way

hy voltage is good butt you need to get it from systems like

a pwm like stanley meyer did

on a other note:

question

if I am making hho and i separate them or make them separate at ones

and there is only tap water in it

there is gonne be chlorine in it

on witch side the O or the H2 side is gonna come chlorine dioxide

Hi hydrogenpower.be. You can fracture H2 and O2 from straight deionized water (0 mineral elements) yes. The problem is the conductivity of the water is very low so you will either need to use chokes and VIC process that Stan Meyer created or you can do what i am doing, displace the current over as much surface exposure to your cell plates as possible.

About a week ago i flushed my cells and ran straight deionized water with out any electrolyte whatsoever. I was only able to transfer 1-2 amps at 28 volts, but i was actually able to make a small pure hydrogen torch flame, while venting the O2, on that current. This would in theory actually work just fine if you had 20 cells to distribute 10-20 amps.

You will have some trace elements of chlorine or chloride gas in with your O2 or H2 if it is in your source water or electrolyte of course. Off the cathode or anode is a good question, but there shouldn't be that much, in my opinion. Soon i will be able to switch my slow investment, into this technology, toward gas instrumentation and analysis and i will know more.

Thanks for dropping in and participating.

[thedude]

Regards, became'm new member of this forum, from self-interest to make hydrogen - oxygen generator separately, but I have been putting some devices and I was somewhat apparent success ...

Now as I read your comments and discussion of Sebu thrill of waking up, I want him to do as soon as possible!

I calculated everything and put it in the folder with drawings generator diktung seals, active Hastelloy electrodes,

Reading passports nothing difficult or complicated to make it, only one incomplete information about the search cone separator, which comes between the active plate, I found a site if you are thinking of this type of nylon that could be used as an excellent membrane separator _


100% silkscreen nylon - Google претрага



Here is the link and see!

Which can be attached to find and buy ... Here I'll show you my work on h2 Dry Cell System




I think this is a good choice nylon screen to take the membrane, but we still need a qualified person to confirm, because I was taking stiff fabrics that are not so well demonstrated, loss-making, increase the apparent resistance and thereby reduce The efficiency of the generator, here are some pictures to look at my generator that does not function normally because it has not yet been made but lives on paper

I couldn't find a lot of specific info on your link but for the mil thickness. There are going to be different micron spec for the mesh its self i would imagine. However, i don't have that info either. Best i can do is show you another image of what we are using. Reg might be able to elaborate a bit more than I of course.

[thedude]

Hi dude, HHo group, in facebook, HHO Philippines, Come, join us will we succulent files............https://www.facebook.com/groups/360232803470/

Hi Henry! Nice to see you here. I'll be trying to stay updated here a bit better in the future. However i definitely will come check out your group. Thanks man.

I am planning to make water boiling and honestly I already have a plan about this matter but my concern is my mind always seeking this question, what are the best material you are going to use so that you can successfully made this kind of water boiling? can you give me some idea or any tips about my concern.

Hi Aric. I'm guessing that your using a language translator and we are getting some confused questioning here. Please be more specific about what you mean by "water boiling"? Do you intend to use hydrogen or HHO to boil water for a steam generator? Or do you actually mean (by "boiling") electrolysis of water into H2 and O2?

Thanks and nice to see you here guys!

[cowboyrx]

Found it!

He has a few videos posted related to this design. Starts out with a smaller version 5x5 and moves up to the 8x8.

GSC = Gas Splitter Cell

8X8 GSC 8-13-2010 005.3gp

YouTube - 8X8 GSC 8-13-2010 005.3gp

8X8 GSC Construction Method
Videos Series
Part 1

He is also in the process of building a spectrophotometer to analyze the qualities in the separated gases.

He speaks/shows of it in the 4:50 mark on the below video:

8X8 GSC 1st Run 9-18-2010.3gp
YouTube - 8X8 GSC 1st Run 9-18-2010.3gp


Ash has a course up at Panacea that is copyrighted to Bill Williams:

http://www.panaceauniversity.org/5X5...upport_Doc.pdf

IndianaBoys

I have some extra plates, gaskets and membranes for this design (all parts ready to assemble!). Please PM me if interested