Peter Daysh Davey Water Heater Query

[cornfused]

stainless shim stock.

Boguslaw,
Try a place locally that sells industrial bearings for stuff like conveyors. Those places will sell shim stock used for aligning shafts to motors, etc. You can buy all sorts of thicknesses and materials. Hope this helps.
Jason

[RAMSET]

Pearls To The Grateful!!

Duncan
Wonderful analogy,and explanations ! Having spent some time at 27mghz {CB}
I agree... and thank you so much for taking the time to explain your thoughts.

Plus you showcased some of our friends work!! Mr. "T" {AKA the Boss [That was his "NOW" clock and goethe repost]

To cool for words ....................
Thanks
Chet

[Duncan]

http://www.mds975.co.uk/Images/radios/atu09.jpg

https://lh6.googleusercontent.com/-txu9gaP5CFE/TnDgk6V6E9I/AAAAAAAAACw/AiynqelMLRs/s500/Mr%252520floyyd.png

New Free Energy by George Mitchell - YouTube

ThaneCHeins's Channel - YouTube

ThaneCHeins's Channel - YouTube

F.M.CHALKALIS ENERGY MULTIPLIER - YouTubehttp://www.rocketradio.co.uk/ekmps/s...mhz-1010-p.jpg

spurious emissions Light tubes lite up under powerlines without plugs? EMF Cra - YouTube

[Slovenia]

Threaded Rod Ring Holder (Updated Mfg Method)

Well, there is a more exact way to cut the slot in the threaded rod than using a hacksaw. Everyone has a hacksaw, but keeping the cut straight with a hacksaw is very hard. I have a $75 industrial hacksaw and I cut my slot a little off too. Anyway, there is a much easier way to do it and it's cheaper than using an industrial hacksaw. You need a dremel tool and a 1.25" cutoff fiber wheel. You can get inexpensive Chinese dremel type tools for less than $20 and the cutoff wheels are cheap too. You can get these cheaper copies of dremel tools at Harbor Freight and they do just as good a job as the real Dremel tool. The main difference is that the real Dremel fits your hand perfectly and is much more comfortable to use. See Mfg. Method below:

Vice up you threaded rod with the part of the threaded rod to be cut sticking out from the vice approximately one inch. You'll be using the vice as a hand rest as well as for securing the threaded rod. You'll need to use both hands to stabilize and keep the tool head running straight as you guide it slowly into the end of the threaded rod. Start off at a lower speed setting to make your initial mark in the threaded rod. Once you have begun your slot on slow speed and everything is lined up nicely, you can speed up your tool. You'll be cutting on both sides of the threaded rod for ease and to make your slot look very sharp and true.

Anyway, this works very well and a Chinese copy of the Dremel is much cheaper than a good industrial hacksaw. Let me know if this works for you.

This instruction is provided for the regular guy who has no formal training in the shop.

I am self taught myself.

[Duncan]

[Slovenia]

Arizona Iced Tea Can ($.99 @ Walmart)

I picked up one of the domestic 23 oz Arizona Iced Tea cans today at Walmart. It is 72.9mm wide and Mr. "C" called for 65mm width, but I think it will work. I'll be giving it a shot by this weekend for you.

[Duncan]

I picked up one of the domestic 23 oz Arizona Iced Tea cans today at Walmart. It is 72.9mm wide and Mr. "C" called for 65mm width, but I think it will work. I'll be giving it a shot by this weekend for you.

I wait with baited breath, the passion barely constrained within my bosom!

[eternalightwithin]

Damn, I'd picked up two cans the night before last, and haven't had a chance to measure them yet. Was hoping for the motherload.
Oh well, the tea was tasty.

David P.

I picked up one of the domestic 23 oz Arizona Iced Tea cans today at Walmart. It is 72.9mm wide and Mr. "C" called for 65mm width, but I think it will work. I'll be giving it a shot by this weekend for you.

[boguslaw]

Still many questions remain unanswered and I also propose to test device with inverter but where is hot and neutral connection in inverter output ?

[MonsieurM]

Have you guys thought about just keeping the same ratio....height/width , thickness/to height etc....and you have fixed ratio from which you can work with no matter what the size of the can....if harmony there is, it will exist also when you do ratios....


by the way 72 hz if you read the previous post on harmonic math is 14.4/2

7 1/4" == 75hz.
7" === 74hz.
6 7/8"== 72hz.
6 3/4"== 71hz.
6 9/16"==72hz.
6 1/2" ==72hz.
6 3/8" ==73hz.
6 1/4" ==75hz.
6 1/8" ==75hz.
6" == 75hz.

COHERENCE AT ANY LEVEL IS COHERENCE AT ALL LEVELS.
An orderly arrangement between wave lengths establishes a connection between frequencies and fields. But for this connection to last, it must resonate to all frequencies and fields. This can only be accomplished through the resonate structure of golden mean pathways. a harmonic cascade effect

[daemonbart]

Sweden

Only a little water apart

Daemonbart,

Are you in Europe ? I'm from Poland.

[FOI]

Some information on inductive heating using circuits

High Frequency Induction Heating

This link describes circuits used to induce inductive heating. Might be some information which could be usefull.

[Duncan]

QUOTE=boguslaw;164954]Still many questions remain unanswered and I also propose to test device with inverter but where is hot and neutral connection in inverter output ?[/QUOTE]

[daemonbart]

Many good inputs!

Having hard to keep up with reading all the good inputs from you guys while working and testing more setups of the device

Slovenia will recieve e-mail later tonight with information about some nice progress from todays work with the device

He will post this info here!

There are so many things to talk about and it takes a little time for me to write in english.

One observation i have made is that in "resonance mode" there are four symetrical spirals in the water, i think the spiral is called "the golden spiral" I think it is a good sign

More will come..

Kind rgds D

[MonsieurM]

Having hard to keep up with reading all the good inputs from you guys while working and testing more setups of the device

Slovenia will recieve e-mail later tonight with information about some nice progress from todays work with the device

He will post this info here!

There are so many things to talk about and it takes a little time for me to write in english.

One observation i have made is that in "resonance mode" there are four symetrical spirals in the water, i think the spiral is called "the golden spiral" I think it is a good sign

More will come..

Kind rgds D

I'm all ears and eyes