Here's looking at Euclid (Bogart)

[Duncan]

1 watt challenge.wmv - YouTube

any way I digress I didn't like intimidation when it happened . My car vandalised was enough to seriously balls my life up despite all my bravado . Now this power in / power out stuff . Is these same guys .. Its their mantra if I get a bit prickly and paranoid now and again Its because I've had dealings.
Here is how it really is .. one of the few things that Albert said that was true before he became a major part of the disinformation conspiracy himself is this maxim known by every ten year old
Chas Campbell Free Energy Generator - YouTube

I tried to ignore that question not because I don't know and cant relate it, but because at that time I considered doing so was a serious risk to my well being . Going into the technicalities of this machine and its ilk exposes every nuance of what tptb are putting their efforts into hiding.
To put it bluntly I chickened out, (And I might again) still things have changed a little bit in my favour first is the fact that there is something of a revolution going on (although you may not be aware of it) In many impoverished countries the very poor have managed to master the application of this technology, They perhaps don't fully understand it but that's irrelevant for these people a power source is life and death and hundreds of these machines are being produced in one form or another. This basically means as far as the energy strangle hold and tptb are concerned .. THE JIGS UP . Here's many examples of builds going on right now .. which of course is
only a fraction of a percent of the activity

Directory:Motor-Generator Self-Looped with Usable Energy Left Over - PESWikithe stupidest circuit - YouTube
These next to video's are quite important and I'd like you to consider what both of these machines have in common .. there is actually one common factor to all these machines and its very important that you see what it is. Let me tell you right now .. both of these machines are absolutely legit and I'm happy to put my house on that !

Chas Chambell Free Energy Generator Replica - Generating 2340 Watts using 750W - YouTube

FREE ENERGY Motor Flywheel energy for freedom - YouTubeFREE ENERGY MY ASS!!! - YouTube

Don't let this be you!

Me Hotel California by Camper Van Dan - YouTube

Homeless with 2 ton of junk !

Chris Devine aka .. camper van Dan (I have emailed it doesn't work. I would have even considered going to Ireland for a couple of days to help this guy make his machine work)
[email protected]Chas Campbell - Gravity Wheel - YouTube

[Cornboy 555]

The response is deafening Duncan, the power amplification, and smoothing out, in a flywheel must never be underestimated.

I havn't yet heard an explanatation of what gravity is!!, guess we will have to lump it in with Magnetism.

So much we havn't been taught, funny that!!.

Warm Regards Cornboy.

[Duncan]

The response is deafening Duncan, the power amplification, and smoothing out, in a flywheel must never be underestimated.

I havn't yet heard an explanatation of what gravity is!!, guess we will have to lump it in with Magnetism.

So much we havn't been taught, funny that!!.

Warm Regards Cornboy.

Cornboy this is not essentually a mechanical device at all. It is a High frequency RF device more suited to radio engineers to understand than mechanics It is being driven by magnetic current

[Cornboy 555]

Thanks Duncan, how do you define magnetic current?

[Duncan]

Thanks Duncan, how do you define magnetic current?

Part 3 of 6: Eric Dollard Tesla Longitudinal Wave Energy SBARC Ham Radio with Chris Carson - YouTube PS you'll get on quicker spotting what is similar with those two machines and Chas Campbells too if you wish

[wantomake]

Ready to start

Ok.
I watched all the vids on YouTube, went to the Nest website to look for the plans. But they wanted a donation. If so many others around the world have built this , then can we find the plans too?

Or can this be replicated from the vids? Not wanting to get you or anyone targeted by tptb, cause it's not that big a secret if so many are building it.

An ac motor, large flywheel, generator, pulleys, belts. What did I leave out.

Just as my name states,
wantomake

[Cornboy 555]

Hey Duncan, i am trying to understand the direction from you.

Are you saying that the flywheel etc are not necessary?, that you can directly couple the motor and alternator, and the magnetic current exchange, is what produces the effect?

Regards Cornboy.

[boguslaw]

I plan it simple. I have old 650VA gasoline generator , old style with a big alternator coupled to the engine shaft. I dissassembled what I could and because I was unable to remove crankshaft completely I just cut then piston. Now it's time to lag a little , I have to make or get a part to connect shaft to the DC motor....

[Duncan]

cornboy and boguslaw I have actually explained this system A to Z on another forum but some didn't grasp what I was saying I was trying a different approach here .. however if you go here

The Jigs Up !

you may pick up what's happening and why

[Matthew Jones]

So looking at the video of the fellow running gens in parallel, he was trying too keep them out of phase. Dollard was talking about the "Burn Through" at resonance.

So what your saying is the motor and the gen need to be In phase with each other at an accelerated RPM. IE the first article on driving an induction motor as a gen.

Either way if you could just lay it out simple step by step the flow of power, that will give starting point anyway.

I got some leads on a few things I can get cheap so I am going to give it try. Might take some time to build.

Cheers
Matt

[Duncan]

So looking at the video of the fellow running gens in parallel, he was trying too keep them out of phase. Dollard was talking about the "Burn Through" at resonance.

So what your saying is the motor and the gen need to be In phase with each other at an accelerated RPM. IE the first article on driving an induction motor as a gen.

Either way if you could just lay it out simple step by step the flow of power, that will give starting point anyway.

I got some leads on a few things I can get cheap so I am going to give it try. Might take some time to build.

Cheers
Matt

its series resonance your aiming to achieve and hold Matt just the same as the 3BGS and that big flywheel is there to keep you pretty much on it with different loads. The extra power is from the same source as well the electrostatic wave and magnetic current . Two induction machines joined together will synchronise obviously the voltages must be the same and normally the currents are .. pretty much, .. however you want to force a state of resonance where the voltage and current are out of phase by 90deg you can do that by overloading the small motor to just the right extent. That makes the machines respond to the linear electrostatic wave and magnetic current just as the 3BGS did.
(When you could get it into resonance). .. I haven't attempted a build of this thing but they are popping up like mushrooms. and that's how I see the dots joining. I have been thinking of ways to try make a small .. dirt cheap demonstration one but I'm bit tied up with a Steve Mark attempt right now if that works as I think it will I wont be bothering with any rotating things .. I all ready got machine gunned with flying magnets by the Hatem machine when I lost control of it.

[cornfused]

woo hoo!!

Thanks Duncan!
What a great Christmas gift you have shared! I'm not saying I understand it all, but now we all have a direction to go! Hopefully a few of these mushrooms can now pop up around my neck of the woods! Thanks again, and wishing you and your family a Merry Christmas and A happy Prosperous New Year!
When time allows ill be digging through my "collectables" and see what I can find!

Merry Christmas everyone.
Jason

[mikehull]

Thanks Duncan,

I am one of the "lurkers" who have been following your revalations with great interest. Whilst family commitments restrict ability and time available for experimentation that does not prevent a wish to understand the process and hopefully partake in building in the not too distant future.

I, for one, appreciate your time and energy in this thread and will try my best to understand and keep up. I hope I am not the only one on this forum who only has a basic education and does not understand electronics fully yet.

On behalf of the silent majority, please, please continue to enlighten us.

http://www.energeticforum.com/images/smilies/thanks.gif

All the best for the New Year to all Members

Mike